TLV2344IN - Quad 8V 790kHz Op Amp | Texas Instruments
料号: TLV2344IN ✓ 量产中TLV2344IN 概述
An operational amplifier is an analog signal-conditioning IC that uses high-gain differential feedback to amplify a small voltage difference. The quad-amplifier configuration places four independent amplifiers in one package, reducing component count when a board needs multiple precision analog channels. In the product hierarchy, the TLV2344IN belongs to the operational-amplifier family within amplifier ICs and analog signal-chain devices.
Key characteristics include a quad amplifier arrangement, an 8 V maximum supply, 790 kHz gain-bandwidth product, CMOS construction, and a 14-pin PDIP package with 7.62 mm lead pitch. Rail-to-rail input capability supports signal operation near the supply rails, while the approximately 1.4 mA-per-channel supply demand is useful in portable and low-power instrumentation. The 14-pin package also provides through-hole mounting and socket compatibility where prototype serviceability is important.
The TLV2344IN uses complementary CMOS input stages, matching the LinCMOS low-voltage operational-amplifier family described by Texas Instruments. Low input bias current and low noise-current behavior make the device relevant to high-impedance sensor interfaces. Designers should still evaluate input common-mode range, output swing, slew rate, offset voltage, and stability for the particular feedback network because those operating limits depend on the selected gain and load.
Typical applications include portable instrumentation, low-frequency sensor conditioning, audio preamplification, active filtering, and general analog signal processing. Four integrated channels can support multiple sensor inputs or staged amplifier functions while sharing one supply package. The device is particularly useful where a through-hole package, low-voltage operation, and rail-to-rail input capability are more important than maximum operating bandwidth.
For reliable layouts, connect bypass capacitors close to the supply pins and route sensitive inputs away from switching nodes and high-current return paths. Check resistor values, output loading, and feedback topology against the manufacturer's recommended operating conditions. This page consolidates the device specifications, sourcing information, replacement assessment, and practical design guidance needed to evaluate the TLV2344IN for a new analog circuit.
直接替换替代料: TLV2344IN ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TLV2344IN (相同外形与封装尺寸) ——差异在于 Gain-Bandwidth Product, Package.
MCP6004-I/P
✅ 直接替换联系询价
查看数据手册 →TLV2344IN 最大额定值与电气特性
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Channels | 4 channels |
| Technology | LinCMOS |
| Maximum Supply Voltage | 8 V |
| Gain-Bandwidth Product | 790 kHz |
| Supply Current per Channel | Approximately 1.4 mA |
| Input Common-Mode Capability | Rail-to-rail input |
| 封装 | 14-pin PDIP |
| Package Lead Pitch | 7.62 mm |
| 安装类型 | Through-hole |
| RoHS 状态 | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
TLV2344IN 引脚配置
| 引脚 1 | OUT1 — Output of amplifier 1 |
| 引脚 2 | IN1- — Inverting input of amplifier 1 |
| 引脚 3 | IN1+ — Non-inverting input of amplifier 1 |
| 引脚 4 | V+ — Positive supply connection |
| 引脚 5 | IN2+ — Non-inverting input of amplifier 2 |
| 引脚 6 | IN2- — Inverting input of amplifier 2 |
| 引脚 7 | OUT2 — Output of amplifier 2 |
| 引脚 8 | OUT3 — Output of amplifier 3 |
| 引脚 9 | IN3- — Inverting input of amplifier 3 |
| 引脚 10 | IN3+ — Non-inverting input of amplifier 3 |
| 引脚 11 | V- — Negative supply connection |
| 引脚 12 | IN4+ — Non-inverting input of amplifier 4 |
| 引脚 13 | IN4- — Inverting input of amplifier 4 |
| 引脚 14 | OUT4 — Output of amplifier 4 |
典型应用
TLV2344IN 适用于 6 应用s: Portable Sensor Signal Conditioning, Audio Preamplification, Active Filtering, Industrial Instrumentation, Battery-Powered Equipment, Data-Acquisition Front End.
Portable Sensor Signal Conditioning
The TLV2344IN suits portable sensor interfaces because it combines four CMOS amplifier channels, rail-to-rail input operation, and approximately 1.4 mA of supply current per channel. Place each amplifier around a sensor stage to provide gain, buffering, or level shifting without adding four separate packages. Its 790 kHz gain-bandwidth product accommodates low- and moderate-bandwidth sensors, while the 14-pin PDIP format simplifies through-hole prototyping and socket-based service. Confirm the sensor output range and required common-mode behavior before selecting the feedback network.
推荐
Audio Preamplification
The TLV2344IN can provide low-voltage audio preamplification in portable and compact analog systems. Its rail-to-rail input characteristic allows the amplifier to operate near the supply limits, while the quad configuration supports multiple audio channels or auxiliary signal paths. The 790 kHz gain-bandwidth product is suitable for audio-band amplification rather than high-frequency video work. Check output swing, load impedance, slew rate, and noise against the selected gain so the four-channel IC does not introduce clipping or instability.
推荐
Active Filtering
The four independent channels in the TLV2344IN are useful for active filters in instrumentation and control products. Each amplifier can implement a low-pass, high-pass, or other feedback network, reducing component count while keeping the circuit organized around one 14-pin PDIP package. The 790 kHz gain-bandwidth product gives designers useful bandwidth for low-frequency filtering, and rail-to-rail input operation supports signals near the supply rails. Simulate the closed-loop response because noise gain, phase margin, and loaded output behavior determine filter stability.
推荐
Industrial Instrumentation
The TLV2344IN fits industrial instrumentation modules that require several low-voltage analog channels on a through-hole board. Four amplifiers can condition pressure, position, temperature, or current-sensor outputs while sharing a common supply package. The approximately 1.4 mA-per-channel supply demand helps limit power use in distributed systems, and the 790 kHz gain-bandwidth product covers many slowly varying process signals. Validate input protection, grounding, common-mode range, and calibration stability for each industrial measurement channel.
推荐
Battery-Powered Equipment
The TLV2344IN is useful in battery-powered test equipment where four low-power analog channels are needed in a through-hole package. Rail-to-rail input operation supports a large portion of the available supply range, while the approximately 1.4 mA-per-channel current provides a useful starting point for power-budget analysis. The device's 790 kHz gain-bandwidth product fits measurement and control loops operating below its upper bandwidth limit. Calculate total load current, regulator dropout, and shutdown requirements because the amplifier current is only one part of the complete battery system.
推荐
Data-Acquisition Front End
The TLV2344IN can condition multiple inputs before conversion in a compact data-acquisition system. Its four-channel organization supports repeated amplifier topologies, such as non-inverting gain stages, buffers, or active filters, while the 14-pin PDIP package is convenient for through-hole prototype boards. The 790 kHz gain-bandwidth product is suitable for sensors and instrumentation signals operating well below the device bandwidth. Check the converter input range and acquisition time, then account for amplifier settling and output drive to avoid losing measurement accuracy.
推荐
推荐产品汇总
工程参考数据: TLV2344IN ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MCP6004 |
|---|---|---|
| Package | 14-pin PDIP | 14-pin PDIP |
| Brand | Texas Instruments | Microchip Technology |
| Number of Channels | 4 channels | 4 channels |
| Amplifier Architecture | General-purpose CMOS operational amplifier | General-purpose CMOS operational amplifier |
| Supply Current per Channel | Approximately 1.4 mA | Approximately 1.4 mA |
| Input Common-Mode Capability | Rail-to-rail input | Rail-to-rail input |
| Mounting Type | Through-hole | Through-hole |
关键差异点
- Manufacturer-specified 790 kHz gain-bandwidth performance (对比 MCP6004)
- Documented low-power operation (对比 MCP6004)
- Four-channel rail-to-rail-input integration (对比 MCP6004)
设计说明
Place the positive- and negative-supply bypass capacitors immediately adjacent to pins 4 and 11, with short, low-inductance traces between the capacitor, package lead, and ground reference. Keep each amplifier's feedback resistors close to its assigned input and output pins to reduce parasitic pickup. Maintain a common return path for the four channels and avoid routing sensitive inputs beneath digital clock lines or switching-regulator nodes.
Do not assume rail-to-rail input operation guarantees an equally rail-to-rail output swing. Check the output-voltage limits under the intended load, especially when driving a back-to-back ADC input, reference circuit, or long PCB trace. Also verify that the selected closed-loop gain remains stable with the output capacitance and resistive load presented by the design.
Estimated: using four channels at approximately 1.4 mA per channel gives an amplifier supply-current estimate of 5.6 mA at the specified operating point. The estimate excludes bias current, output-load current, regulator quiescent current, and external components. Add those loads when sizing the supply and include startup current margin when choosing the regulator and protection scheme.
合规信息
The verified product information does not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is treated as not applicable because the product is not identified as an automotive-qualified device.