Texas Instruments

TLV2460IP - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments

料号: TLV2460IP ✓ 量产中
6 V Vdss 14 nA Id 8-pin PDIP Package
最小起订量: 1 |

TLV2460IP 概述

Texas Instruments TLV2460IP is a single-amplifier, rail-to-rail input/output operational amplifier with a 6 V supply rating, 6.4 MHz gain-bandwidth product, and shutdown capability, housed in an 8-pin PDIP package. The device combines a 1.6 V/us slew rate with input bias current of 14 nA and an input offset voltage of 500 uV, making it suitable for portable, low-voltage signal-conditioning systems.

An operational amplifier is a voltage-controlled differential amplifier used to amplify errors and control feedback loops. The TLV2460 belongs to the rail-to-rail input/output amplifier category, with input common-mode range extending beyond the supply rails and output swing approaching both rails. This places it within the amplifier IC hierarchy of signal-chain and analog-conditioning components used in portable instrumentation, sensor interfaces, audio paths, and low-voltage industrial systems.

The 6.4 MHz gain-bandwidth product supports higher closed-loop bandwidth than slower general-purpose amplifiers, while the 1.6 V/us slew rate improves response to fast voltage changes. Rail-to-rail input behavior increases usable signal range in low-voltage systems, and rail-to-rail output swing provides additional headroom. A shutdown function can reduce operating demand when the circuit is not active, although the exact shutdown timing and current values should be confirmed in the manufacturer datasheet.

The TLV2460IP uses a conventional single-supply operational-amplifier architecture intended for low-voltage operation. Its 500 uV offset specification is relevant to precision DC conditioning, while the 14 nA bias current limits input-amplifier loading on high-impedance sources. Designers must still account for input bias-current error, offset drift, output-current limits, noise, and stability when applying it around sensors, filters, or feedback networks.

Typical uses include portable battery-powered measurement systems, low-voltage sensor interfaces, audio signal conditioning, general-purpose analog filters, and industrial control modules. In each case, the 6 V maximum supply and rail-to-rail behavior are useful for compact systems where the signal can approach the available supply range. The PDIP package also favors through-hole assembly, prototyping, and designs that require a socketable amplifier.

For stable operation, place input and feedback components close to the amplifier, decouple the supply pins, and verify output settling before clocked or measurement systems begin acquisition. Use shutdown only after checking timing relationships elsewhere in the circuit, because shutting down the amplifier during a conversion can invalidate the measurement.

This page combines the manufacturer's device description with practical application guidance, drop-in family options, comparison parameters, and design guidance. It emphasizes verified package compatibility and practical trade-offs rather than treating differently packaged amplifier variants as direct replacements.

直接替换替代料: TLV2460IP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: TLV2460IP (相同外形与封装尺寸).

Texas Instruments
对比 TLV2460IP →

TLV2460AIP

✅ 直接替换 ⚠️ 规格未核验
📦 PDIP-8 (P)
Automotive-qualified family variant; nominal 6 V supply and 6.4 MHz bandwidth remain identical, with qualification and environmental limits differing.

📋 参考替代料(不在目录中)

TLV2460CP

✅ 直接替换 ⚠️ 规格未核验
Texas Instruments
📦 PDIP-8 (P)
Single operational amplifier · CMOS · 6 V · 6.4 MHz · Rail-to-rail input · Rail-to-rail output · Yes · Low-power operational amplifier

联系询价

查看数据手册 →

TLV2460AIPG4

✅ 直接替换 ⚠️ 规格未核验
📦 PDIP-8 (P)
Automotive-qualified green-rohs ordering variant; electrical headline ratings remain 6 V and 6.4 MHz with 0% nominal difference.

📋 参考替代料(不在目录中)

TLV2460CPE4

✅ 直接替换 ⚠️ 规格未核验
📦 PDIP-8 (P)
Commercial family variant with an E4 ordering suffix; nominal 6 V supply and 6.4 MHz bandwidth match, with no quantified headline difference.

📋 参考替代料(不在目录中)

TLV2460IPE4

✅ 直接替换 ⚠️ 规格未核验
📦 PDIP-8 (P)
Same TLV2460IP family device with an E4 ordering suffix; nominal 6 V supply and 6.4 MHz bandwidth are unchanged, with 0% headline difference.

📋 参考替代料(不在目录中)

TLV2460IP 最大额定值与电气特性

Number of Channels 1 channel
Amplifier Type Single operational amplifier
Maximum Supply Voltage 6 V
Gain-Bandwidth Product 6.4 MHz
Slew Rate 1.6 V/us
Input Bias Current 14 nA
Input Offset Voltage 500 uV
Rail-to-Rail Input Rail-to-rail
Rail-to-Rail Output Rail-to-rail
Shutdown Function Yes
封装 8-pin PDIP
Package Pitch 7.62 mm
安装类型 Through-hole
Product Category Standard general-purpose amplifier

TLV2460IP 引脚配置

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
引脚 1 NC — Not connected
引脚 2 IN- — Inverting input
引脚 3 IN+ — Non-inverting input
引脚 4 V- — Negative supply or ground connection
引脚 5 SHDN — Shutdown control input
引脚 6 OUT — Amplifier output
引脚 7 V+ — Positive supply input
引脚 8 NC — Not connected

典型应用

TLV2460IP 适用于 6 应用s: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Low-Noise Audio Preamplifier, Industrial Control Amplifier, Active Analog Filter, Data Acquisition Front End.

📱

Portable Sensor Signal Conditioning

The TLV2460IP fits portable sensor interfaces because its 14 nA input bias current minimizes loading on high-impedance sources, while the 6.4 MHz gain-bandwidth product provides useful bandwidth for filtering and gain stages. Its rail-to-rail input behavior allows the sensed voltage to use more of a low-voltage supply range than a conventional fixed-range amplifier. Place the device close to the sensor and condition the output with the compensation network required for the selected closed-loop gain. The 1.6 V/us slew rate helps preserve large-signal fidelity, although the 500 uV input offset must be included in the error budget for precision measurements.

🔋

Battery-Powered Instrumentation

TLV2460IP is appropriate for battery-powered instrumentation that must preserve signal headroom at low supply voltages. The rail-to-rail input and output characteristics reduce the usable signal restriction imposed by the supply rails, and the 6.4 MHz bandwidth supports faster acquisition and control loops than typical micropower amplifiers. Its shutdown capability can help a portable instrument disable the amplifier during inactive intervals when the system architecture permits. Because the exact supply and shutdown current values are not listed in the product record, evaluate total energy use from the manufacturer datasheet before sizing the battery and power-management circuitry.

🎧

Low-Noise Audio Preamplifier

The TLV2460IP can serve as a general-purpose audio preamplifier in portable and low-voltage analog systems. Its 6.4 MHz gain-bandwidth product and 1.6 V/us slew rate provide ample closed-loop bandwidth for audio-band signals and prevent slew-rate limiting in moderately demanding stages. Rail-to-rail output swing can improve headroom when the amplifier operates from a compact supply. Audio performance still depends on the configured gain, source impedance, feedback network, and load, so evaluate noise and distortion from the manufacturer datasheet and verify the output stage against the intended speaker or line input.

🏭

Industrial Control Amplifier

TLV2460IP supports low-voltage industrial control and measurement modules that require a conventional single amplifier with flexible gain-setting networks. Its 6.4 MHz bandwidth is suitable for servo-error, transducer, and feedback paths, while rail-to-rail operation helps accommodate sensor signals that approach the supply limits. The PDIP package supports through-hole assembly and socketed maintenance designs common in industrial equipment. Designers should provide local supply decoupling, keep feedback traces short, and confirm stable operation for every intended closed-loop gain and capacitive-load condition before releasing the controller to production.

🔧

Active Analog Filter

The TLV2460IP is useful in active filter designs where a 6 V supply and approximately 6.4 MHz gain-bandwidth product are sufficient for the signal bandwidth. Its rail-to-rail input and output behavior expands the usable operating region in low-voltage filters, and the 1.6 V/us slew rate helps maintain low distortion for larger transient outputs. Select resistor and capacitor values around the desired poles and Q, then verify stability and tolerance because real component variation shifts filter response. Place the feedback components adjacent to the amplifier to reduce parasitic feedback and sensitivity to board contamination.

🖥️

Data Acquisition Front End

TLV2460IP can form the buffer or gain stage immediately preceding an ADC in a low-voltage data-acquisition design. The 6.4 MHz bandwidth is more than adequate for many moderate-rate sensing systems, while rail-to-rail input operation helps preserve small signals within the available input range. The 14 nA bias current is useful when the source impedance is high, and the 500 uV offset specification must be included in the measurement uncertainty. Use an antialias filter, local decoupling, and an output settling check so that the amplifier does not introduce acquisition errors during the converter's sample window.

What is the operating voltage of TLV2460IP?
The TLV2460IP supports a maximum supply voltage of 6 V. According to the Texas Instruments TLV2460 product description, the device is a single, 6 V, 6.4 MHz rail-to-rail input/output operational amplifier with shutdown. This rating makes it appropriate for portable and industrial systems operating from low-voltage rails. The exact recommended operating range, input common-mode limits, and output swing should be taken from the manufacturer datasheet when designing signal headroom around the 6 V ceiling.
What are the key specifications of TLV2460IP that engineers should know?
The TLV2460IP combines a 6 V supply rating, 6.4 MHz gain-bandwidth product, 1.6 V/us slew rate, 14 nA input bias current, and 500 uV input offset voltage in an 8-pin PDIP package. Texas Instruments identifies it as a single amplifier with rail-to-rail input and output capability plus shutdown. These figures position it between low-speed micropower amplifiers and much faster high-voltage devices, making it a practical choice for portable instrumentation, sensor conditioning, and general-purpose analog signal chains.
Where can I download the TLV2460IP datasheet PDF?
The official TLV2460IP datasheet can be accessed through the Texas Instruments TLV2460 product page or the TLV2460IP part-details page. The manufacturer product page identifies the device as a 6 V, 6.4 MHz, rail-to-rail operational amplifier with shutdown, while the part-details entry identifies the 8-pin PDIP package. Use the manufacturer copy for final pinout, recommended operating conditions, electrical characteristics, and application guidance.
Where can I find the TLV2460IP pinout?
The TLV2460IP pinout is located in the pin-configuration section of the Texas Instruments TLV2460 family datasheet. The TLV2460IP ordering information identifies an 8-pin PDIP package, allowing the correct package drawing and pin-description table to be selected before assigning PCB tracks. The shutdown-capable single-amplifier configuration includes supply, input, output, shutdown, and no-connect positions; verify every signal against the datasheet table.
Is TLV2460IP suitable for low-voltage sensor interfaces?
The TLV2460IP is suitable for low-voltage sensor interfaces because it combines rail-to-rail input and output behavior with a 14 nA input bias current and 6.4 MHz bandwidth. The low bias current reduces loading on high-impedance sensors, while the rail-to-rail input range can improve signal utilization in compact systems. Its 500 uV offset rating should be checked against the required sensor accuracy, and supply bypass capacitors should be placed close to the device.
What can replace TLV2460IP on the same 8-pin PDIP footprint?
The strongest same-footprint replacements are the TLV2460 family variants that retain an 8-pin PDIP package, including TLV2460AIP, TLV2460CP, TLV2460AIPG4, TLV2460CPE4, and TLV2460IPE4. Their qualification and ordering suffixes differ, so the replacement must be selected according to temperature, qualification, and procurement requirements rather than package alone. Confirm the complete electrical ratings and shutdown polarity in the manufacturer datasheet before approving a substitution.
TLV2460IP vs TLV2460AIP: which is better for automotive use?
TLV2460AIP is the more appropriate choice when the design requires the automotive-qualified version of the same TLV2460 family in an 8-pin PDIP package. The target TLV2460IP is described by Texas Instruments as a standard general-purpose amplifier, while the A designation distinguishes the automotive variant. Both retain the 6 V, 6.4 MHz, rail-to-rail architecture in the stated family context, but qualification, temperature range, and ordering details must be checked against the specific manufacturer datasheet.
TLV2460IP vs TLV2460CP: what should I check before replacing it?
The TLV2460CP can be considered only after confirming that its complete electrical characteristics, qualification range, and shutdown behavior satisfy the target circuit. Both parts belong to the TLV2460 family and use the 8-pin PDIP format, which supports a direct footprint comparison. Review the manufacturer datasheets for supply current, offset, noise, input range, output swing, and temperature limits because a matching package alone does not guarantee equivalent production qualification.
When should I choose TLV2460IP over TLV2460AIP?
Choose TLV2460IP when a standard-grade, general-purpose 8-pin PDIP amplifier is sufficient and automotive qualification is not required. Its 6.4 MHz bandwidth, 1.6 V/us slew rate, and rail-to-rail behavior are suitable for portable measurement, sensor conditioning, audio, and low-voltage industrial modules. Choose TLV2460AIP instead when the system requires the automotive-qualified family variant and its specified environmental limits are supported by the completed design.
Is TLV2460IP the same as TLV2460CP?
The TLV2460IP and TLV2460CP share the same 8-pin PDIP format and the TLV2460 family identification, but they are not automatically identical for every production requirement. The ordering suffixes distinguish qualification, temperature, or grade attributes that must be reviewed in the datasheets. For an existing PCB, the footprint is compatible; for an approved replacement, verify the electrical limits, environmental ratings, shutdown behavior, and any qualification documents.
What is the best cross-brand equivalent for TLV2460IP?
No cross-brand 8-pin PDIP equivalent can be identified reliably from the available component records. The verified records identify the target's package and family alternatives but do not establish a competitor part with a documented pin-for-pin function and matching shutdown polarity. Use the Texas Instruments family options for a controlled footprint-compatible review, or request engineering support for a cross-brand qualification using the required supply voltage, bandwidth, offset, input bias, slew rate, and shutdown requirements.
Where to buy TLV2460IP online?
Use the Request a Quote form on this page to request TLV2460IP availability, current commercial terms, and lead time. The form allows buyers to specify the exact 8-pin PDIP ordering code and required quantity without relying on stale catalog information. For design continuity, include the target MPN TLV2460IP and any acceptable qualification or lifecycle constraints in the request.
What is the lead time for TLV2460IP?
The current lead time for TLV2460IP should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package allocation, and supply status, so a general statement would not be reliable for production planning. Include the required quantity, delivery location, target date, and whether an alternate 8-pin PDIP family variant is acceptable in the quotation request.
Is TLV2460IP in stock?
Current TLV2460IP stock should be confirmed through the Request a Quote form on this page. The manufacturer product page confirms the device and package, but stock is time-dependent and should not be inferred from a search-result listing. A quotation request can provide the current allocation, order quantity, and delivery estimate for the exact TLV2460IP ordering code.
How much does TLV2460IP cost?
The current commercial price for TLV2460IP should be obtained through the Request a Quote form on this page. Pricing depends on quantity, package form, market conditions, and any required production qualification, so a static figure would age quickly. Specify the order quantity and required delivery details to receive a current quotation for the exact MPN.
Does TLV2460IP include a shutdown function?
Yes, the TLV2460IP includes a shutdown function. Texas Instruments describes the TLV2460 as a single, 6 V, 6.4 MHz, rail-to-rail input/output operational amplifier with shutdown. The shutdown pin must still be managed according to the manufacturer datasheet, including its polarity, timing, and behavior during transitions, before it is used for power sequencing or duty-cycle control.

工程参考数据: TLV2460IP ——对比、设计指导和合规信息。

选型指南

Choose TLV2460IP for a standard-grade, low-voltage, single-amplifier design that needs rail-to-rail input and output operation, a 6.4 MHz gain-bandwidth product, and shutdown in an 8-pin PDIP package. It is well suited to portable sensor conditioning, low-voltage instrumentation, audio preamplification, active filtering, and ADC input stages. Select TLV2460AIP or TLV2460AIPG4 when the project requires the corresponding automotive-qualified family variant. Consider TLV2460CP or TLV2460CPE4 when the commercial ordering grade better matches procurement or qualification requirements. TLV2460IPE4 is the closest same-footprint family option for designs that do not need the automotive designation. For every alternative, confirm shutdown polarity, electrical limits, temperature range, qualification status, and stability in the manufacturer datasheet. A matching PDIP footprint removes the need for a PCB change, but it does not remove the need for application-level verification.

与替代料对比

参数 本产品 TLV2460AIP TLV2460CP TLV2460AIPG4 TLV2460CPE4 TLV2460IPE4
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package PDIP-8 (P) PDIP-8 (P) PDIP-8 (P) PDIP-8 (P) PDIP-8 (P) PDIP-8 (P)
Number of Channels 1 1 1 1 1 1

关键差异点

  • Combines 6.4 MHz bandwidth with shutdown in an 8-pin PDIP amplifier (对比 TLV2460AIP)
  • Uses a 14 nA input bias current for higher-impedance signal conditioning (对比 TLV2460CP)
  • Standard general-purpose 8-pin PDIP configuration supports prototype and through-hole assembly (对比 TLV2460AIPG4)

设计说明

Place the input, feedback, and compensation components close to the TLV2460IP pins, particularly the inverting input because parasitic capacitance can alter the closed-loop response. Route the ground return directly to the supply-decoupling ground point and maintain a compact path from the supply pin to its bypass capacitor. The 8-pin PDIP package provides generous lead spacing, but lead inductance still becomes relevant when the input network includes high-gain or high-speed feedback paths.

Use a local bypass capacitor at the positive supply connection and connect the negative supply pin to the circuit ground. Confirm bypass capacitance, ESR, and placement against the manufacturer stability guidance. Because the TLV2460IP supports a maximum 6 V supply, leave transient margin for supply tolerance and ringing; do not operate from a rail that can exceed the manufacturer limit. The shutdown control must remain in a defined state during startup and normal operation.

Do not treat the rail-to-rail input and output descriptions as unlimited signal range. The usable range depends on supply voltage, common-mode limits, output load, output-current capability, and the selected operating point. For precision sensor interfaces, include the 500 uV input offset and 14 nA input bias current in the error calculation, and verify settling time before using the amplifier immediately ahead of an ADC conversion.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The available product records identify the TLV2460IP as a Texas Instruments 8-pin PDIP operational amplifier but do not state the required compliance or automotive qualification values. Use the G4 ordering option only after confirming its associated compliance documentation.

相关搜索

TLV2460IP datasheet TLV2460IP pinout TLV2460IP datasheet pdf TLV2460IP specifications TLV2460IP equivalent TLV2460IP replacement TLV2460IP cross reference TLV2460IP vs TLV2460AIP TLV2460IP PDIP footprint TLV2460IP application circuit Texas Instruments TLV2460IP TLV2460IP price TLV2460IP stock 6V 6.4MHz operational amplifier TLV2460IP sensor interface

相关元器件 & 术语

Texas Instruments TLV2460IP TLV2460AIP TLV2460CP TLV2460AIPG4 TLV2460CPE4 TLV2460IPE4 operational amplifier rail-to-rail input/output amplifier single amplifier low-voltage analog IC signal-conditioning IC PDIP-8 through-hole package 6 V power supply 6.4 MHz gain-bandwidth product 1.6 V/us slew rate 14 nA input bias current 500 uV input offset voltage shutdown function rail-to-rail input rail-to-rail output portable instrumentation sensor signal conditioning active analog filter
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情