TLV2460IP - 6V, 6.4MHz RRIO Op Amp with Shutdown | Texas Instruments
MPN: TLV2460IP ✓ פעילTLV2460IP סקירה
An operational amplifier is a voltage-controlled differential amplifier used to amplify errors and control feedback loops. The TLV2460 belongs to the rail-to-rail input/output amplifier category, with input common-mode range extending beyond the supply rails and output swing approaching both rails. This places it within the amplifier IC hierarchy of signal-chain and analog-conditioning components used in portable instrumentation, sensor interfaces, audio paths, and low-voltage industrial systems.
The 6.4 MHz gain-bandwidth product supports higher closed-loop bandwidth than slower general-purpose amplifiers, while the 1.6 V/us slew rate improves response to fast voltage changes. Rail-to-rail input behavior increases usable signal range in low-voltage systems, and rail-to-rail output swing provides additional headroom. A shutdown function can reduce operating demand when the circuit is not active, although the exact shutdown timing and current values should be confirmed in the manufacturer datasheet.
The TLV2460IP uses a conventional single-supply operational-amplifier architecture intended for low-voltage operation. Its 500 uV offset specification is relevant to precision DC conditioning, while the 14 nA bias current limits input-amplifier loading on high-impedance sources. Designers must still account for input bias-current error, offset drift, output-current limits, noise, and stability when applying it around sensors, filters, or feedback networks.
Typical uses include portable battery-powered measurement systems, low-voltage sensor interfaces, audio signal conditioning, general-purpose analog filters, and industrial control modules. In each case, the 6 V maximum supply and rail-to-rail behavior are useful for compact systems where the signal can approach the available supply range. The PDIP package also favors through-hole assembly, prototyping, and designs that require a socketable amplifier.
For stable operation, place input and feedback components close to the amplifier, decouple the supply pins, and verify output settling before clocked or measurement systems begin acquisition. Use shutdown only after checking timing relationships elsewhere in the circuit, because shutting down the amplifier during a conversion can invalidate the measurement.
This page combines the manufacturer's device description with practical application guidance, drop-in family options, comparison parameters, and design guidance. It emphasizes verified package compatibility and practical trade-offs rather than treating differently packaged amplifier variants as direct replacements.
חלופות תחליף ישיר עבור TLV2460IP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TLV2460IP (אותו גורם צורה וטביעת רגל).
TLV2460AIP
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2460CP
✅ Drop-In ⚠️ מפרטים לא מאומתיםצור קשר לקבלת מחיר
הצג גיליון נתונים ←TLV2460AIPG4
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2460CPE4
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2460IPE4
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2460IP דירוגים מרביים ומאפיינים חשמליים
| Number of Channels | 1 channel |
| Amplifier Type | Single operational amplifier |
| Maximum Supply Voltage | 6 V |
| Gain-Bandwidth Product | 6.4 MHz |
| Slew Rate | 1.6 V/us |
| Input Bias Current | 14 nA |
| Input Offset Voltage | 500 uV |
| Rail-to-Rail Input | Rail-to-rail |
| Rail-to-Rail Output | Rail-to-rail |
| Shutdown Function | Yes |
| מארז | 8-pin PDIP |
| Package Pitch | 7.62 mm |
| סוג הרכבה | Through-hole |
| Product Category | Standard general-purpose amplifier |
תצורת פינים של TLV2460IP
| פין 1 | NC — Not connected |
| פין 2 | IN- — Inverting input |
| פין 3 | IN+ — Non-inverting input |
| פין 4 | V- — Negative supply or ground connection |
| פין 5 | SHDN — Shutdown control input |
| פין 6 | OUT — Amplifier output |
| פין 7 | V+ — Positive supply input |
| פין 8 | NC — Not connected |
יישומים טיפוסיים
TLV2460IP מתאים עבור 6 יישוםs: Portable Sensor Signal Conditioning, Battery-Powered Instrumentation, Low-Noise Audio Preamplifier, Industrial Control Amplifier, Active Analog Filter, Data Acquisition Front End.
Portable Sensor Signal Conditioning
The TLV2460IP fits portable sensor interfaces because its 14 nA input bias current minimizes loading on high-impedance sources, while the 6.4 MHz gain-bandwidth product provides useful bandwidth for filtering and gain stages. Its rail-to-rail input behavior allows the sensed voltage to use more of a low-voltage supply range than a conventional fixed-range amplifier. Place the device close to the sensor and condition the output with the compensation network required for the selected closed-loop gain. The 1.6 V/us slew rate helps preserve large-signal fidelity, although the 500 uV input offset must be included in the error budget for precision measurements.
מומלץ
Battery-Powered Instrumentation
TLV2460IP is appropriate for battery-powered instrumentation that must preserve signal headroom at low supply voltages. The rail-to-rail input and output characteristics reduce the usable signal restriction imposed by the supply rails, and the 6.4 MHz bandwidth supports faster acquisition and control loops than typical micropower amplifiers. Its shutdown capability can help a portable instrument disable the amplifier during inactive intervals when the system architecture permits. Because the exact supply and shutdown current values are not listed in the product record, evaluate total energy use from the manufacturer datasheet before sizing the battery and power-management circuitry.
מומלץ
Low-Noise Audio Preamplifier
The TLV2460IP can serve as a general-purpose audio preamplifier in portable and low-voltage analog systems. Its 6.4 MHz gain-bandwidth product and 1.6 V/us slew rate provide ample closed-loop bandwidth for audio-band signals and prevent slew-rate limiting in moderately demanding stages. Rail-to-rail output swing can improve headroom when the amplifier operates from a compact supply. Audio performance still depends on the configured gain, source impedance, feedback network, and load, so evaluate noise and distortion from the manufacturer datasheet and verify the output stage against the intended speaker or line input.
מומלץ
Industrial Control Amplifier
TLV2460IP supports low-voltage industrial control and measurement modules that require a conventional single amplifier with flexible gain-setting networks. Its 6.4 MHz bandwidth is suitable for servo-error, transducer, and feedback paths, while rail-to-rail operation helps accommodate sensor signals that approach the supply limits. The PDIP package supports through-hole assembly and socketed maintenance designs common in industrial equipment. Designers should provide local supply decoupling, keep feedback traces short, and confirm stable operation for every intended closed-loop gain and capacitive-load condition before releasing the controller to production.
מומלץ
Active Analog Filter
The TLV2460IP is useful in active filter designs where a 6 V supply and approximately 6.4 MHz gain-bandwidth product are sufficient for the signal bandwidth. Its rail-to-rail input and output behavior expands the usable operating region in low-voltage filters, and the 1.6 V/us slew rate helps maintain low distortion for larger transient outputs. Select resistor and capacitor values around the desired poles and Q, then verify stability and tolerance because real component variation shifts filter response. Place the feedback components adjacent to the amplifier to reduce parasitic feedback and sensitivity to board contamination.
מומלץ
Data Acquisition Front End
TLV2460IP can form the buffer or gain stage immediately preceding an ADC in a low-voltage data-acquisition design. The 6.4 MHz bandwidth is more than adequate for many moderate-rate sensing systems, while rail-to-rail input operation helps preserve small signals within the available input range. The 14 nA bias current is useful when the source impedance is high, and the 500 uV offset specification must be included in the measurement uncertainty. Use an antialias filter, local decoupling, and an output settling check so that the amplifier does not introduce acquisition errors during the converter's sample window.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TLV2460IP — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLV2460AIP | TLV2460CP | TLV2460AIPG4 | TLV2460CPE4 | TLV2460IPE4 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | PDIP-8 (P) | PDIP-8 (P) | PDIP-8 (P) | PDIP-8 (P) | PDIP-8 (P) | PDIP-8 (P) |
| Number of Channels | 1 | 1 | 1 | 1 | 1 | 1 |
מבדילים עיקריים
- Combines 6.4 MHz bandwidth with shutdown in an 8-pin PDIP amplifier (לעומתTLV2460AIP)
- Uses a 14 nA input bias current for higher-impedance signal conditioning (לעומתTLV2460CP)
- Standard general-purpose 8-pin PDIP configuration supports prototype and through-hole assembly (לעומתTLV2460AIPG4)
הערות תכנון
Place the input, feedback, and compensation components close to the TLV2460IP pins, particularly the inverting input because parasitic capacitance can alter the closed-loop response. Route the ground return directly to the supply-decoupling ground point and maintain a compact path from the supply pin to its bypass capacitor. The 8-pin PDIP package provides generous lead spacing, but lead inductance still becomes relevant when the input network includes high-gain or high-speed feedback paths.
Use a local bypass capacitor at the positive supply connection and connect the negative supply pin to the circuit ground. Confirm bypass capacitance, ESR, and placement against the manufacturer stability guidance. Because the TLV2460IP supports a maximum 6 V supply, leave transient margin for supply tolerance and ringing; do not operate from a rail that can exceed the manufacturer limit. The shutdown control must remain in a defined state during startup and normal operation.
Do not treat the rail-to-rail input and output descriptions as unlimited signal range. The usable range depends on supply voltage, common-mode limits, output load, output-current capability, and the selected operating point. For precision sensor interfaces, include the 500 uV input offset and 14 nA input bias current in the error calculation, and verify settling time before using the amplifier immediately ahead of an ADC conversion.
מידע על תאימות
The available product records identify the TLV2460IP as a Texas Instruments 8-pin PDIP operational amplifier but do not state the required compliance or automotive qualification values. Use the G4 ordering option only after confirming its associated compliance documentation.