TPA3220DDW - 60W Stereo Class-D Amplifier | Texas Instruments
料号: TPA3220DDW ✓ 量产中TPA3220DDW 概述
A Class-D amplifier is a switching audio-output stage whose efficiency is substantially higher than that of a conventional linear amplifier at comparable output power. Its hierarchy extends from audio amplifiers to power-management semiconductors. The TPA3220 family combines analog input conditioning, a feedback-controlled Class-D output stage, thermal protection, and efficient power conversion in one device, reducing the number of external components required for a compact audio output channel.
Key features include greater than 90% efficiency, idle power below 0.25 W, standby power below 0.1 W, and a closed-loop feedback bandwidth extending to 100 kHz. Its optimized gate-drive design and 70 mΩ MOSFET output devices support efficient full-power operation. Four input-gain settings allow the same amplifier to accommodate different source levels without redesigning the analog front end.
The TPA3220 supports both analog-differential (AD) modulation and low-idle-current HEAD modulation. AD operation provides conventional differential behavior, while HEAD modulation targets lower idle consumption when the amplifier is not delivering substantial audio power. The 100 kHz feedback bandwidth helps reduce distortion within the audio band, while the analog input interface supports both single-ended and differential signal sources.
Typical applications include stereo speaker systems, mono subwoofer amplifiers, powered multimedia speakers, soundbars, home-audio receivers, television audio platforms, and compact consumer-audio products. The 7 V to 32 V supply range accommodates automotive and portable-system rails after the appropriate input filtering, protection, and power-conversion stages have been designed.
For implementation, place the exposed-pad thermal interface and input/output capacitors according to the manufacturer layout guidance. Confirm the speaker load, thermal performance, analog gain, and filter selection before production. The manufacturer datasheet should be used to verify pin assignments, absolute maximum ratings, and exposed-pad land geometry.
直接替换替代料: TPA3220DDW ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TPA3220DDWR
✅ 直接替换📋 参考替代料(不在目录中)
TPA3220DDW 最大额定值与电气特性
| Stereo Output Power | 60 W |
| Mono Peak Output Power | 110 W |
| Supply Voltage Range | 7 V to 32 V |
| Amplifier Type | Class-D |
| Audio Input Type | Analog input |
| Maximum Analog Input | 2 V RMS |
| Selectable Gain Settings | 18 dB, 24 dB, 30 dB, and 34 dB |
| Feedback Bandwidth | Up to 100 kHz |
| Peak Efficiency | >90% |
| Idle Power | <0.25 W |
| Standby Power | <0.1 W |
| Output MOSFET Resistance | 70 mΩ |
| Channel Configuration | 1-channel mono or 2-channel stereo |
| Modulation Modes | Analog differential (AD) or low-idle-current HEAD |
| 封装 | 44-pin HTSSOP (DDW) with exposed pad |
| Package Width | 6.20 mm |
TPA3220DDW 6.20 mm 引脚配置指南
TPA3220DDW(6.20 mm 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TPA3220DDW.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TPA3220DDW 适用于 6 应用s: Stereo Powered Speaker, Compact Subwoofer Amplifier, Home Theater Soundbar, Powered Monitor Speaker, Automotive Audio Amplifier, Portable Speaker System.
Stereo Powered Speaker
The TPA3220DDW fits a stereo powered-speaker design requiring up to 60 W per channel from a 7 V to 32 V supply. Its four analog gain settings accommodate source levels from 18 dB through 34 dB, allowing input scaling without changing the amplifier architecture. The 100 kHz feedback bandwidth supports low audio-band distortion, while greater than 90% efficiency reduces heat in continuously active speakers. Place the output filters, input network, and exposed-pad ground connection according to the manufacturer reference layout.
Compact Subwoofer Amplifier
For a compact subwoofer, TPA3220DDW can operate in its 110 W peak mono configuration while using the same analog-input Class-D architecture as a stereo design. The 70 mΩ MOSFET output stage and greater than 90% efficiency are valuable when amplifier heat must be limited in a sealed or space-constrained enclosure. Designers should use the manufacturer output-filter and thermal guidance and verify continuous power against the selected speaker impedance and supply rail.
Home Theater Soundbar
The TPA3220DDW is suitable for soundbar amplification where low idle power, compact packaging, and stereo output capability are important. Its standby power below 0.1 W and selectable AD or HEAD modulation allow the system designer to balance playback efficiency against low-power behavior. The 44-pin HTSSOP with exposed pad supports dense layouts, but thermal analysis remains necessary because continuous audio output can raise junction temperature despite the amplifier's high conversion efficiency.
Powered Monitor Speaker
A powered studio or desktop monitor can use the TPA3220DDW for efficient analog-input amplification with up to 60 W stereo output. The 18 dB, 24 dB, 30 dB, and 34 dB gain choices simplify adaptation to line-level source voltages, while the differential-input option helps reject noise when the source and amplifier share a ground reference. Use short, shielded analog routes and the manufacturer input-filter values to preserve audio-band signal integrity.
Automotive Audio Amplifier
The TPA3220DDW's 7 V to 32 V supply range and efficient Class-D output stage can fit automotive audio power stages where available supply voltage is constrained. Its 110 W peak mono capability is useful for a subwoofer channel, and the 60 W stereo rating supports two front-channel outputs. Automotive qualification status, transient protection, and operating-temperature limits must be confirmed from the manufacturer documentation before using the device in a vehicle application.
Portable Speaker System
The TPA3220DDW suits portable or battery-assisted speakers because greater than 90% efficiency improves the usable output obtained from a limited power budget. The low-idle-current HEAD mode and standby power below 0.1 W are useful when the amplifier is enabled intermittently, while the seven-volt minimum operating voltage supports suitably designed low-voltage rails. Protection, reverse-polarity control, battery transients, and acoustic output limits must be handled outside the amplifier.
工程参考数据: TPA3220DDW ——对比、设计指导和合规信息。
选型指南
设计说明
The DDW package uses its exposed pad as the primary thermal path. Connect the pad to the PCB ground plane with multiple thermal vias and preserve the manufacturer land-pattern dimensions. Continuous output power and ambient temperature determine the required copper area; even a greater-than-90%-efficient amplifier converts a portion of its input power into heat. Check the exposed-pad temperature during maximum-output operation rather than relying only on amplifier efficiency.
Use the manufacturer layout as the basis for the input filter, output filter, power connections, and exposed-pad land. Keep the analog input route away from the Class-D switching nodes and the high-current output paths. Place input and output capacitors at the pins identified by the application diagram, and provide a continuous, low-impedance ground reference between the exposed pad, input return, and output-filter return.
Do not substitute a generic 44-pin HTSSOP footprint without checking the DDW exposed-pad dimensions and paste pattern. Also confirm the selected AD or HEAD modulation mode, analog gain, mono bridge configuration, and speaker load against the manufacturer data. The four gain settings are mutually exclusive operating choices, and their availability through configuration pins must be verified for the intended board revision.
合规信息
The available product information does not state RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status. Confirm these requirements with the manufacturer before qualification.