TS393IPT - Dual Micropower Open-Drain Comparator | ST
料号: TS393IPT ✓ 量产中TS393IPT 概述
A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its output state when the relationship between those voltages changes. The TS393 belongs to the comparator hierarchy within interface and signal-conditioning ICs. Its dual-channel architecture provides two comparators in one package, reducing component count while maintaining low power consumption for battery-powered, industrial, and instrumentation systems.
Key features include a 2.7 V minimum operating voltage, a 16 V maximum operating voltage, typical consumption of 9 μA per comparator, and a 2.5 μs response time. The open-drain outputs can pull a logic rail low while permitting the output node to remain in a high-impedance state. This output structure is useful when interfacing with systems that require wired open-collector behavior, external pull-up resistors, or shared bus signaling.
The TS393 uses CMOS circuitry and is intended for general-purpose comparison rather than high-speed signal-chain timing. Compared with bipolar dual comparators, the TS393 is positioned as a lower-power alternative, with the manufacturer describing typical consumption as approximately 20 times lower than the bipolar LM393. Its two channels share the same device supply but otherwise perform independent input comparisons.
Typical applications include battery-powered sensing, industrial threshold detection, sensor-interface conditioning, window comparison in control systems, and low-power monitoring modules. The 8-pin TSSOP package supports compact PCB layouts, while the open-drain outputs permit flexible interfacing to MCU input pins, optocouplers, relays, and other pull-up-based logic devices when their electrical limits are compatible with the application.
Designers should account for common-mode input limits, output pull-up requirements, propagation-delay behavior, and input signals that remain within the comparator's operating range. Because the outputs are open drain, every output node requires an appropriate pull-up arrangement for normal digital operation. Keep sensitive input traces short, provide a stable local supply connection, and avoid excessive capacitive loading where faster transitions are needed.
This page combines the manufacturer device information, commercial sourcing guidance, same-footprint alternative analysis, and practical interface-design guidance to help engineers evaluate the TS393IPT beyond a basic distributor parameter listing.
直接替换替代料: TS393IPT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TSX393IPT
✅ 直接替换📋 参考替代料(不在目录中)
TS393IPT 最大额定值与电气特性
| Product Type | Dual voltage comparator |
| Comparator Channel Count | 2 channels |
| Technology | CMOS |
| Supply Voltage Range | 2.7 V to 16 V |
| Typical Supply Current | 9 μA per comparator |
| Response Time | 2.5 μs |
| 输出类型 | Open-drain |
| Output Compatibility | CMOS open-drain |
| 封装 | 8-pin TSSOP |
| 安装类型 | Surface mount |
TS393IPT 8-pin tssop 引脚配置指南
TS393IPT(8-pin tssop 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS393IPT.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS393IPT 适用于 6 应用s: Battery-Powered Sensor Threshold Detection, Industrial Monitoring and Control, Low-Power Environmental Monitoring, Portable Equipment Window Comparator, Open-Drain Interface and Signal Conditioning, Automated Equipment Limit Detection.
Battery-Powered Sensor Threshold Detection
The TS393IPT fits battery-powered sensing because each comparator channel typically operates with 9 μA of supply current, while the 2.7 V to 16 V range supports low-voltage and higher regulated industrial rails. The two channels can independently compare sensor outputs with adjustable reference voltages to detect upper and lower operating thresholds. Place the device near the sensor interface to minimize noise-sensitive input routing, and account for pull-up current when the open-drain output is low. Because no input common-mode limits are stated in the product information, verify that sensor and reference voltages remain within the manufacturer limits before finalizing the circuit.
Industrial Monitoring and Control
TS393IPT is useful in industrial monitoring systems that compare a measured voltage against a process threshold and generate a logic event for a controller. Its dual-channel architecture supports two independent decisions within one 8-pin TSSOP package, helping conserve board area. The open-drain output can signal a pull-up-based input, optocoupler, or relay-driver stage when voltage, current, and isolation requirements are compatible. The 16 V maximum supply supports a broad range of regulated equipment rails, while the 2.5 μs response time suits threshold events rather than high-speed pulse qualification. Apply grounding and filtering practices appropriate to factory environments.
Low-Power Environmental Monitoring
The TS393IPT can compare signals from light, temperature, and other analog sensors in compact environmental monitors. Its typical 9 μA-per-comparator consumption reduces the portion of system standby demand associated with threshold detection, and the 2.7 V minimum operating voltage accommodates common battery-derived rails. Two channels allow the design to define an upper and lower alarm window around a sensor signal. The comparator does not replace the sensor's analog signal conditioning, so gain, filtering, and reference accuracy must be established upstream. Pull-up values should balance low standby current against the input transition rate required by the monitoring MCU.
Portable Equipment Window Comparator
A portable instrument can use the TS393IPT's two channels as a window comparator, with one channel detecting the lower threshold and the other detecting the upper threshold. The 8-pin TSSOP package supports compact layouts in handheld and wearable-adjacent equipment, while the 9 μA typical channel current is appropriate for battery-operated operation. Both outputs are open drain, allowing separate pull-ups or a shared arrangement where the system logic supports it. Designers should define threshold hysteresis with external resistor networks, verify input behavior near the common-mode range, and ensure pull-up loading does not create an unacceptable drain on the battery rail.
Open-Drain Interface and Signal Conditioning
TS393IPT fits signal-conditioning paths that need a wired open-drain event rather than a push-pull CMOS output. A comparator channel can translate an analog decision into a wired logic signal for a pull-up-equipped MCU, bus, or optoelectronic interface. The open-drain architecture gives the output a high-impedance released state, which can support shared signaling when the system design guarantees that only one device asserts the bus at a time. The 2.5 μs response time and 2.7 V minimum supply suit general-purpose conditioning rather than high-speed timing tasks. Confirm sink-current margin, pull-up voltage, capacitance, and fault-state behavior across the complete interface network.
Automated Equipment Limit Detection
The TS393IPT can support automatic limit detection in automated test or process equipment by comparing two system voltages against references. Its dual-channel arrangement reduces the number of comparator packages needed when two independent limits must be evaluated. The open-drain outputs can trigger downstream machine-control logic through compatible pull-up interfaces, while the 2.5 μs response time provides fast enough settling for many general-purpose measurements. For dependable production behavior, keep reference generation and input routing quiet, provide local supply bypassing close to the device, and validate behavior at every expected process boundary. Common-mode and offset limits should be taken directly from the manufacturer electrical tables.
工程参考数据: TS393IPT ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TSX393IPT |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 8-TSSOP | 8-TSSOP - same |
| Product Type | Dual voltage comparator | Dual comparator |
| Comparator Count | 2 channels | 2 channels |
| Technology | CMOS | CMOS |
| Output Type | Open-drain | Open-drain |
关键差异点
- Two comparator channels in one compact package (对比 TSX393IPT)
- Low typical channel consumption (对比 TSX393IPT)
- Wide low-voltage supply range (对比 TSX393IPT)
设计说明
Include both comparator channels and the continuous current drawn by each output pull-up in the power budget. The TS393 typically consumes 9 μA per comparator, but a pull-up continuously connected to the supply can dominate standby consumption whenever the open-drain output is asserted low. Select the pull-up from the required sink current and switching speed, then verify the worst-case supply drain during a low output state.
Route each comparator input and reference directly to the associated device pins, and keep these paths away from switching nodes and the open-drain output return current. Place any input or reference filtering components close to the pins they serve. The 8-pin TSSOP footprint is compact, so small placement errors can couple noisy signals into the high-impedance comparison inputs and create false threshold transitions.
Do not treat an open-drain output as a actively driven logic-high output. The released state requires a correctly chosen pull-up, and the pull-up voltage must remain compatible with the device's output ratings. Also verify that both input signals remain inside the allowed common-mode range. Supply-voltage compatibility alone does not guarantee correct comparison behavior near the device's lower operating limit.
Check the rising-edge rate formed by the output pull-up and total node capacitance before using a TS393 output to clock another circuit. The comparator's 2.5 μs response specification describes transition behavior, but it does not eliminate the additional rise time imposed by a high resistance and a capacitive load. Lower pull-up resistance improves edge speed at the cost of higher current and should be selected for the receiving circuit's actual requirements.
合规信息
Compliance status must be confirmed against the current manufacturer product documentation and the declaration associated with the ordered MPN.