STMicroelectronics

TS393IPT - Dual Micropower Open-Drain Comparator | ST

MPN: TS393IPT ✓ Active
2.7 V to 16 V Vdss 9 μA per comparator Id 8-pin TSSOP Package
MOQ: 1 |

TS393IPT Overview

The STMicroelectronics TS393IPT is a micropower CMOS dual voltage comparator with two independent comparison channels, a typical supply current of 9 μA per comparator, a 2.5 μs response time, and an operating voltage range of 2.7 V to 16 V. The device is supplied in an 8-pin TSSOP package and uses open-drain outputs. It is designed for low-power signal conditioning where two threshold decisions are required in a compact surface-mount footprint.

A voltage comparator is an analog integrated circuit that compares an input voltage with a reference voltage and changes its output state when the relationship between those voltages changes. The TS393 belongs to the comparator hierarchy within interface and signal-conditioning ICs. Its dual-channel architecture provides two comparators in one package, reducing component count while maintaining low power consumption for battery-powered, industrial, and instrumentation systems.

Key features include a 2.7 V minimum operating voltage, a 16 V maximum operating voltage, typical consumption of 9 μA per comparator, and a 2.5 μs response time. The open-drain outputs can pull a logic rail low while permitting the output node to remain in a high-impedance state. This output structure is useful when interfacing with systems that require wired open-collector behavior, external pull-up resistors, or shared bus signaling.

The TS393 uses CMOS circuitry and is intended for general-purpose comparison rather than high-speed signal-chain timing. Compared with bipolar dual comparators, the TS393 is positioned as a lower-power alternative, with the manufacturer describing typical consumption as approximately 20 times lower than the bipolar LM393. Its two channels share the same device supply but otherwise perform independent input comparisons.

Typical applications include battery-powered sensing, industrial threshold detection, sensor-interface conditioning, window comparison in control systems, and low-power monitoring modules. The 8-pin TSSOP package supports compact PCB layouts, while the open-drain outputs permit flexible interfacing to MCU input pins, optocouplers, relays, and other pull-up-based logic devices when their electrical limits are compatible with the application.

Designers should account for common-mode input limits, output pull-up requirements, propagation-delay behavior, and input signals that remain within the comparator's operating range. Because the outputs are open drain, every output node requires an appropriate pull-up arrangement for normal digital operation. Keep sensitive input traces short, provide a stable local supply connection, and avoid excessive capacitive loading where faster transitions are needed.

This page combines the manufacturer device information, commercial sourcing guidance, same-footprint alternative analysis, and practical interface-design guidance to help engineers evaluate the TS393IPT beyond a basic distributor parameter listing.

Drop-in alternatives for TS393IPT — same package, pin-to-pin compatible. Different-package parts requiring PCB rework are excluded.

TSX393IPT

✅ Drop-In
📦 8-TSSOP
Same dual CMOS open-drain comparator architecture and 8-TSSOP footprint; detailed electrical differences require manufacturer-table verification.

📋 Reference alternative (not in catalog)

TS393IPT Maximum Ratings & Electrical Characteristics

Product Type Dual voltage comparator
Comparator Channel Count 2 channels
Technology CMOS
Supply Voltage Range 2.7 V to 16 V
Typical Supply Current 9 μA per comparator
Response Time 2.5 μs
Output Type Open-drain
Output Compatibility CMOS open-drain
Package 8-pin TSSOP
Mounting Type Surface mount

TS393IPT 8-pin tssop Pin Configuration Guide

Pin configuration for TS393IPT (8-pin tssop package). This analog component features input, output, and power supply pins. Refer to the manufacturer datasheet for offset null, compensation, and enable pin configurations. Ideal for signal conditioning and amplifier circuits.

8-pin tssop package pinout diagram for TS393IPT

No detailed pinout data available for TS393IPT.

Refer to the datasheet for full pin configuration.

Typical Applications

TS393IPT is suitable for 6 applications: Battery-Powered Sensor Threshold Detection, Industrial Monitoring and Control, Low-Power Environmental Monitoring, Portable Equipment Window Comparator, Open-Drain Interface and Signal Conditioning, Automated Equipment Limit Detection.

🔋

Battery-Powered Sensor Threshold Detection

The TS393IPT fits battery-powered sensing because each comparator channel typically operates with 9 μA of supply current, while the 2.7 V to 16 V range supports low-voltage and higher regulated industrial rails. The two channels can independently compare sensor outputs with adjustable reference voltages to detect upper and lower operating thresholds. Place the device near the sensor interface to minimize noise-sensitive input routing, and account for pull-up current when the open-drain output is low. Because no input common-mode limits are stated in the product information, verify that sensor and reference voltages remain within the manufacturer limits before finalizing the circuit.

🏭

Industrial Monitoring and Control

TS393IPT is useful in industrial monitoring systems that compare a measured voltage against a process threshold and generate a logic event for a controller. Its dual-channel architecture supports two independent decisions within one 8-pin TSSOP package, helping conserve board area. The open-drain output can signal a pull-up-based input, optocoupler, or relay-driver stage when voltage, current, and isolation requirements are compatible. The 16 V maximum supply supports a broad range of regulated equipment rails, while the 2.5 μs response time suits threshold events rather than high-speed pulse qualification. Apply grounding and filtering practices appropriate to factory environments.

🧩

Low-Power Environmental Monitoring

The TS393IPT can compare signals from light, temperature, and other analog sensors in compact environmental monitors. Its typical 9 μA-per-comparator consumption reduces the portion of system standby demand associated with threshold detection, and the 2.7 V minimum operating voltage accommodates common battery-derived rails. Two channels allow the design to define an upper and lower alarm window around a sensor signal. The comparator does not replace the sensor's analog signal conditioning, so gain, filtering, and reference accuracy must be established upstream. Pull-up values should balance low standby current against the input transition rate required by the monitoring MCU.

📱

Portable Equipment Window Comparator

A portable instrument can use the TS393IPT's two channels as a window comparator, with one channel detecting the lower threshold and the other detecting the upper threshold. The 8-pin TSSOP package supports compact layouts in handheld and wearable-adjacent equipment, while the 9 μA typical channel current is appropriate for battery-operated operation. Both outputs are open drain, allowing separate pull-ups or a shared arrangement where the system logic supports it. Designers should define threshold hysteresis with external resistor networks, verify input behavior near the common-mode range, and ensure pull-up loading does not create an unacceptable drain on the battery rail.

🔧

Open-Drain Interface and Signal Conditioning

TS393IPT fits signal-conditioning paths that need a wired open-drain event rather than a push-pull CMOS output. A comparator channel can translate an analog decision into a wired logic signal for a pull-up-equipped MCU, bus, or optoelectronic interface. The open-drain architecture gives the output a high-impedance released state, which can support shared signaling when the system design guarantees that only one device asserts the bus at a time. The 2.5 μs response time and 2.7 V minimum supply suit general-purpose conditioning rather than high-speed timing tasks. Confirm sink-current margin, pull-up voltage, capacitance, and fault-state behavior across the complete interface network.

🏭

Automated Equipment Limit Detection

The TS393IPT can support automatic limit detection in automated test or process equipment by comparing two system voltages against references. Its dual-channel arrangement reduces the number of comparator packages needed when two independent limits must be evaluated. The open-drain outputs can trigger downstream machine-control logic through compatible pull-up interfaces, while the 2.5 μs response time provides fast enough settling for many general-purpose measurements. For dependable production behavior, keep reference generation and input routing quiet, provide local supply bypassing close to the device, and validate behavior at every expected process boundary. Common-mode and offset limits should be taken directly from the manufacturer electrical tables.

What is the TS393IPT and what does it do?
The TS393IPT is a dual micropower CMOS voltage comparator with two independent channels, 9 μA typical supply current per comparator, and open-drain outputs. According to the STMicroelectronics TS393 product page, it is designed for general-purpose low-power comparison and is packaged in an 8-pin TSSOP. Each channel compares a signal voltage against a reference and changes state when the input relationship crosses the threshold.
What is the operating voltage range of TS393IPT?
The TS393IPT operates from 2.7 V to 16 V. This range allows it to be used in low-voltage battery-powered systems as well as industrial and instrumentation circuits operating above the traditional 5 V logic level. The 16 V maximum supply also provides headroom for systems with regulated intermediate rails, although each comparator input must remain within its specified common-mode limits.
How much current does TS393IPT consume?
The TS393IPT typically consumes 9 μA per comparator, or approximately 18 μA for both channels under the manufacturer's stated typical condition. The STMicroelectronics TS393 product page describes this as about 20 times lower consumption than the bipolar LM393. Actual current depends on supply voltage, output state, input levels, and switching activity, so both channels should be evaluated in the final power budget.
What are the key specifications of TS393IPT that engineers should know?
The TS393IPT combines two CMOS comparator channels, a 2.7 V to 16 V supply range, 9 μA typical current per comparator, a 2.5 μs response time, and open-drain outputs in an 8-pin TSSOP. According to the STMicroelectronics TS393 product page, its low typical consumption makes it suitable for micropower sensing and monitoring. The open-drain architecture is the defining interface feature and requires suitable pull-up arrangements.
Why does TS393IPT use open-drain outputs?
The TS393IPT uses open-drain outputs so the output transistor can pull the node low but leaves it electrically released when inactive. This supports wired logic, bus-style signaling, level translation, and direct interfaces with pull-up-equipped devices. A suitable pull-up resistor is required for normal high-level operation, and its value should be selected from the output sink-current and rise-time requirements of the application.
Where can I download the TS393IPT datasheet PDF?
The official TS393 device information and datasheet are available through the STMicroelectronics product page at https://www.st.com/en/amplifiers-and-comparators/ts393.html. The page identifies TS393 as a micropower CMOS dual voltage comparator and is the preferred source for pin assignments, electrical limits, application examples, and ordering information. Use the manufacturer's document revision associated with the product page for formal design verification.
Where can I find the TS393IPT pinout?
The TS393IPT pinout is shown in the manufacturer documentation for the TS393 family and should be used when assigning the eight TSSOP leads. The TS393IPT suffix identifies the packaged 8-pin TSSOP version, while its comparator channels require separate input, reference, output, supply, and ground connections. Before laying out a PCB, verify each lead and exposed function against the current manufacturer pin-description table.
Is TS393IPT suitable for battery-powered sensor applications?
Yes, TS393IPT is suitable for many battery-powered sensor applications because it operates from 2.7 V and typically consumes 9 μA per comparator. Its dual-channel architecture can monitor two threshold conditions without requiring two separate comparator packages. The system designer should also account for pull-up resistor current, sensor current, input bias effects, and the leakage of downstream digital devices when calculating the complete standby-current budget.
When should I choose TS393IPT instead of TSX393IPT?
Choose TS393IPT for the standard TS393 dual-comparator configuration, and consider TSX393IPT when its listed electrical or qualification characteristics better match the design. Both are identified as CMOS open-drain dual comparators in 8-TSSOP packages, but a board-level replacement still requires checking every pin function, input range, timing value, and lifecycle condition. The TS393 product page remains the controlling reference for the target device.
TS393IPT vs TSX393IPT: which comparator is better for low-power sensing?
TS393IPT and TSX393IPT both appear as 8-pin TSSOP, CMOS, open-drain dual comparators, making TSX393IPT a close same-footprint alternative. TS393IPT is specifically identified as micropower, with typical consumption of 9 μA per comparator and a 2.5 μs response time. Selection should therefore emphasize the complete electrical tables and required qualification conditions, not package appearance alone, when one variant has application-specific advantages.
What is the best drop-in replacement for TS393IPT?
TSX393IPT is the closest documented drop-in candidate in the 8-TSSOP comparator category, with the same dual CMOS open-drain architecture and surface-mount footprint. The available manufacturer and distributor information does not establish a complete set of five pin-compatible alternatives, so no additional parts are presented as drop-in replacements. Confirm pin mapping, common-mode range, supply limits, output behavior, and timing before releasing any substitution for production.
Can TSX393IPT replace TS393IPT on an existing PCB?
TSX393IPT can be considered for an existing TS393IPT PCB because both are listed as 8-pin TSSOP, dual CMOS comparators with open-drain outputs. A true drop-in decision still requires an engineering comparison of pin functions, input common-mode limits, supply range, offset voltage, response time, and output sink capability. PCB fit alone does not prove electrical equivalence, particularly where input signals approach the allowed common-mode limits.
What is a suitable STMicroelectronics equivalent for TS393IPT?
TSX393IPT is the suitable STMicroelectronics same-footprint candidate identified for TS393IPT because it is also an 8-pin TSSOP, dual, CMOS, open-drain comparator. Its use as a drop-in replacement should be conditioned on verification of the detailed electrical tables. No cross-brand equivalent is asserted because the cross-reference results do not establish a pin-compatible part with verified close parametric performance.
Where can I buy TS393IPT and what is the lead time?
Use the Request a Quote form on this page to ask for TS393IPT unit availability, lot quantity, and current lead time. The component is offered in an 8-pin TSSOP package and is described by STMicroelectronics as an active micropower dual comparator. Quote requests should state the required quantity, date code policy, packaging format, and destination so the manufacturer or authorized channel can confirm the correct production commitment.
What is the price of TS393IPT and is it in stock?
Current TS393IPT price and stock status should be obtained through the Request a Quote form on this page rather than from a static price table. The Request a Quote workflow confirms the exact MPN, quantity break, package suffix, and expected delivery date. For design planning, the principal confirmed characteristics are the 2.7 V to 16 V operating range, 9 μA typical current per comparator, and 8-pin TSSOP packaging.
How should pull-up resistors be selected for TS393IPT?
Select each TS393IPT open-drain pull-up using the required logic-high voltage, the output's permitted sink current, the bus capacitance, and the desired rising-edge rate. A smaller resistance produces a faster rising edge but increases supply current continuously while the output is low; a larger resistance reduces that consumption but can slow transitions and increase susceptibility to leakage or noise. Verify both static current and timing in the final circuit.

Engineering reference data for TS393IPT — comparison, design guidance, and compliance information.

Selection Guide

Choose TS393IPT when a design needs two independent low-power threshold comparisons, open-drain signaling, and operation from 2.7 V to 16 V. Its 9 μA typical current per comparator makes it particularly appropriate for portable sensing and monitoring, while the 2.5 μs response time is appropriate for general-purpose threshold events rather than high-speed pulse qualification. Consider TSX393IPT when its full electrical and qualification data provide a closer match for the target design, particularly because it is also listed as a dual CMOS open-drain comparator in an 8-TSSOP package. Verify pin assignments, input common-mode limits, offset voltage, output sink current, and lifecycle status before substitution. Do not choose either device solely for package fit: the open-drain outputs require suitable pull-ups, and both signal inputs must remain within their permitted operating range.

Comparison with Alternatives

Parameter This Product TSX393IPT
Brand STMicroelectronics STMicroelectronics
Package 8-TSSOP 8-TSSOP - same
Product Type Dual voltage comparator Dual comparator
Comparator Count 2 channels 2 channels
Technology CMOS CMOS
Output Type Open-drain Open-drain

Key Differentiators

  • Two comparator channels in one compact package (vs TSX393IPT)
  • Low typical channel consumption (vs TSX393IPT)
  • Wide low-voltage supply range (vs TSX393IPT)

Design Notes

Include both comparator channels and the continuous current drawn by each output pull-up in the power budget. The TS393 typically consumes 9 μA per comparator, but a pull-up continuously connected to the supply can dominate standby consumption whenever the open-drain output is asserted low. Select the pull-up from the required sink current and switching speed, then verify the worst-case supply drain during a low output state.

Route each comparator input and reference directly to the associated device pins, and keep these paths away from switching nodes and the open-drain output return current. Place any input or reference filtering components close to the pins they serve. The 8-pin TSSOP footprint is compact, so small placement errors can couple noisy signals into the high-impedance comparison inputs and create false threshold transitions.

Do not treat an open-drain output as a actively driven logic-high output. The released state requires a correctly chosen pull-up, and the pull-up voltage must remain compatible with the device's output ratings. Also verify that both input signals remain inside the allowed common-mode range. Supply-voltage compatibility alone does not guarantee correct comparison behavior near the device's lower operating limit.

Check the rising-edge rate formed by the output pull-up and total node capacitance before using a TS393 output to clock another circuit. The comparator's 2.5 μs response specification describes transition behavior, but it does not eliminate the additional rise time imposed by a high resistance and a capacitive load. Lower pull-up resistance improves edge speed at the cost of higher current and should be selected for the receiving circuit's actual requirements.

Compliance Information

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Lead Free
Unknown
Halogen Free
Unknown
Conflict Minerals
Unknown

Compliance status must be confirmed against the current manufacturer product documentation and the declaration associated with the ordered MPN.

Data verified on: 2026-11-16 — data verified and curated by XAIPART's component engineering team

Related Searches

TS393IPT datasheet TS393IPT pinout TS393IPT datasheet pdf TS393IPT specifications TS393IPT equivalent TS393IPT replacement TS393IPT vs TSX393IPT TS393IPT open drain comparator TS393IPT TSSOP8 pinout TS393IPT price TS393IPT stock STMicroelectronics TS393IPT

Related Components & Terms

STMicroelectronics TS393IPT TSX393IPT TS393 dual voltage comparator comparator analog interface IC signal-conditioning IC CMOS open-drain output open-collector logic micropower 2.5 μs response time 9 μA supply current 2.7 V minimum supply 16 V maximum supply TSSOP-8 surface-mount package battery-powered sensing industrial threshold detection sensor interface wired logic semiconductor
Quick Quote RFQ
Fill in complete details — our sales team will respond within 24 hours
Part Number Manufacturer Package QTY Target Price Extended
✓
Quote submitted!

We will respond to your email within 24 hours

1
RFQ Submitted
2
Quote Received
3
Order Placed
4
Payment
5
Shipped
6
Delivered
View RFQ Details