STMicroelectronics

TS954IDT - Quad Rail-to-Rail Low-Power Op Amp | STMicroelectronics

料号: TS954IDT ✓ 量产中
2.7 V Vdss 14-pin SOIC Package
最小起订量: 1 |

TS954IDT 概述

The STMicroelectronics TS954IDT is a quad input/output rail-to-rail BiCMOS operational amplifier optimized for 3 V and 5 V operation, with a 2.7 V to 12 V supply-voltage range and four amplifiers in a 14-pin SOIC package. Its rail-to-rail input and output stages support operation close to the supply rails, making the device suitable for portable, industrial, and instrumentation systems that require low-voltage signal conditioning.

An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and amplifies the difference between them. A quad operational amplifier contains four independent amplifier channels in one package. The rail-to-rail BiCMOS category combines complementary bipolar input characteristics with CMOS output stages, while the low-power design targets portable and space-constrained applications.

The TS954IDT provides four rail-to-rail amplifier channels, low-noise input behavior, low distortion, and operation from 2.7 V to 12 V. The manufacturer describes the family as optimized and fully specified for 3 V and 5 V systems. Rail-to-rail input operation improves usable input range, while rail-to-rail output capability allows output voltage to approach the available supply voltage more closely than a conventional non-rail-to-rail output amplifier.

The TS954 family combines four general-purpose amplifiers with a 14-pin SO package. It is intended for applications where several independent analog channels are required, including sensor conditioning, buffer amplification, active filtering, low-level signal processing, and embedded control systems. The shared package consolidates four channels without requiring four separate amplifier packages, reducing board-area requirements.

Typical uses include portable measurement equipment, industrial sensor interfaces, audio and communications signal conditioning, battery-powered instruments, and general-purpose analog subsystems. The 2.7 V minimum supply supports 3 V systems, while the 12 V maximum provides flexibility for 5 V and higher-voltage designs when the applied operating point remains within the device ratings.

When designing around the TS954IDT, verify input and output common-mode limits, output-current demand, capacitive-load stability, and supply voltage for every channel. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be routed away from switching nodes and high-current return paths to preserve low-noise operation.

This product page combines the manufacturer datasheet information with practical application guidance, package details, technical comparisons, and drop-in replacement options. It is intended to help engineers select the correct amplifier, plan the PCB, and assess whether a same-package alternative can simplify an existing design without unnecessary board changes.

直接替换替代料: TS954IDT ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: TS954IDT (相同外形与封装尺寸) ——差异在于 Package, Gain-Bandwidth Product, Input Bias Current, Number of Amplifiers, Output Swing.

STMicroelectronics
Package: 14-pin Small Outline (SO-14)
Gain-Bandwidth Product: 4 MHz
Input Bias Current: 15 nA
对比 TS954IDT →
STMicroelectronics
Package: 8-pin SOIC
Gain-Bandwidth Product: 100 kHz
对比 TS954IDT →
STMicroelectronics
Package: 14-SO small-outline package
Gain-Bandwidth Product: 100 kHz
Input Bias Current: 1 pA
对比 TS954IDT →

TS924IDT

✅ 直接替换 ⚠️ 规格未核验
STMicroelectronics
📦 SOIC-14
4 · General-purpose operational amplifier · BiCMOS · Input and output · 2.7 V to 12 V · 3 V and 5 V · 4 MHz · 1.3 V/µs

联系询价

查看数据手册 →

TS934IDT

✅ 直接替换 ⚠️ 规格未核验
STMicroelectronics
📦 SOIC-14
4 circuits · General-purpose operational amplifier · Rail-to-rail · 2.7 V to 10 V · 100 kHz · 5 mA · 20 uA · 1 pA

联系询价

查看数据手册 →

TS932IDT

✅ 直接替换 ⚠️ 规格未核验
STMicroelectronics
📦 SOIC-14
2 circuits · General-purpose operational amplifier · 2.7 V · 10 V · 20 uA · 100 kHz · 2.9 Vpp at RL = 100 kΩ · CMOS

联系询价

查看数据手册 →

TS954IDT 最大额定值与电气特性

Amplifier Count 4 circuits
Product Type Input/output rail-to-rail low-power operational amplifier
Process Technology BiCMOS
Minimum Supply Voltage 2.7 V
Maximum Supply Voltage 12 V
Optimized Supply Voltage 3 V and 5 V
Input Common-Mode Range Rail-to-rail
Output Swing Rail-to-rail
工作温度范围 -40 °C to +125 °C
封装 14-pin SOIC
安装类型 Surface mount
Amplifier Classification Standard general-purpose amplifier
Distortion 0.01%
Input Type Rail-to-rail
输出类型 Rail-to-rail
Power Class Low power

TS954IDT 引脚配置

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
引脚 1 OUT1 — Operational amplifier 1 output
引脚 2 -IN1 — Operational amplifier 1 inverting input
引脚 3 +IN1 — Operational amplifier 1 non-inverting input
引脚 4 VCC — Positive supply voltage
引脚 5 +IN2 — Operational amplifier 2 non-inverting input
引脚 6 -IN2 — Operational amplifier 2 inverting input
引脚 7 OUT2 — Operational amplifier 2 output
引脚 8 OUT3 — Operational amplifier 3 output
引脚 9 -IN3 — Operational amplifier 3 inverting input
引脚 10 +IN3 — Operational amplifier 3 non-inverting input
引脚 11 VCC — Positive supply voltage
引脚 12 -IN4 — Operational amplifier 4 inverting input
引脚 13 +IN4 — Operational amplifier 4 non-inverting input
引脚 14 OUT4 — Operational amplifier 4 output

典型应用

TS954IDT 适用于 6 应用s: Portable Sensor Signal Conditioning, Industrial Sensor Interface, Low-Voltage Audio Preamplifier, Active Filtering and Buffering, Battery-Powered Measurement Instrument, Communications Signal Conditioning.

📱

Portable Sensor Signal Conditioning

The TS954IDT fits portable measurement systems that need several low-voltage analog channels without allocating space for four individual amplifier packages. Its four input/output rail-to-rail BiCMOS channels operate from 2.7 V to 12 V, allowing the same device family to serve 3 V and 5 V designs. Use the channels to amplify weak sensor outputs, buffer high-impedance sources, and provide gain before an ADC. The low-power architecture is particularly useful in battery-operated instruments, while the -40 °C to +125 °C range supports industrial ambient conditions. Validate each channel’s common-mode range and output swing against the sensor’s operating envelope.

🏭

Industrial Sensor Interface

The TS954IDT can condition several low-level industrial sensor signals in one 14-pin SOIC package. Rail-to-rail inputs help preserve signal information when the input level moves close to either supply rail, while rail-to-rail outputs improve the available output range in 3 V and 5 V systems. Common uses include transducer amplifiers, current-loop interfaces, resistance measurement, and sensor-to-ADC driver stages. Keep the amplifier close to the sensor connector to minimize noise pickup, and verify the TS954’s maximum output-current capability for the ADC input and termination network.

🎧

Low-Voltage Audio Preamplifier

The TS954IDT’s four rail-to-rail amplifier channels are suitable for small-signal audio preamplification in compact, low-voltage equipment. Each channel can provide voltage gain before a line-level stage, while the 2.7 V to 12 V supply range covers 3 V and 5 V portable audio architectures. The family datasheet identifies low distortion and low-noise behavior as important characteristics for this device class. Place the TS954 near the source connector, use short low-impedance signal paths, and confirm the selected channel’s bandwidth and output-current capability for the following audio stage.

🔧

Active Filtering and Buffering

The quad TS954IDT supports parallel active-filter and buffer stages in 3 V or 5 V analog systems. Four channels allow several stages to be implemented with one package, reducing component count and simplifying power distribution. Its rail-to-rail input and output characteristics are useful for filters whose signal occupies a large portion of the supply range, while the low-power BiCMOS design supports compact control and monitoring equipment. Determine each filter’s stability and noise performance at the actual source and load impedances, and place passive filter components close to the associated amplifier pins.

🧩

Battery-Powered Measurement Instrument

The TS954IDT is appropriate for battery-powered measurement equipment requiring four low-voltage amplifier channels in a compact footprint. Its 2.7 V minimum supply supports 3 V systems, and the manufacturer family is optimized and fully specified for 3 V and 5 V operation. The channels can condition thermocouple, resistive, current, or low-level voltage inputs before conversion. Rail-to-rail behavior helps maximize usable signal range, but low-current operation still requires attention to quiescent current, output-current demand, and the voltage headroom lost in long-divider or gain networks.

🌐

Communications Signal Conditioning

The TS954IDT can provide local amplification and buffering for communications and control signals in compact 3 V or 5 V equipment. Four channels support receiver-side filtering, threshold amplification, line-driver interfacing, and decoupling of sensitive analog stages. Rail-to-rail input behavior is useful when signals span much of the available supply range, and the low-power BiCMOS architecture can simplify portable terminal design. Check the required gain-bandwidth product, slew rate, output-current capability, and capacitive-load stability at the actual line impedance before using a channel as a cable driver.

What is the TS954IDT?
The TS954IDT is a quad input/output rail-to-rail BiCMOS operational amplifier from STMicroelectronics, supplied in a 14-pin SOIC package. According to the STMicroelectronics TS951, TS952 and TS954 family datasheet, the device is optimized and fully specified for 3 V and 5 V operation. Four independent amplifier channels make it suitable for compact analog signal-conditioning systems that need more than one low-voltage amplifier.
What is the operating voltage of TS954IDT?
The TS954IDT operates across a 2.7 V to 12 V supply-voltage range and is optimized for 3 V and 5 V systems. The STMicroelectronics TS951, TS952 and TS954 family datasheet identifies both supply rails as important design limits. Keep every channel’s input and output within its permitted common-mode and output-swing ranges, and confirm the complete application waveform before operating near a supply extreme.
Where can I download the TS954IDT datasheet PDF?
The official STMicroelectronics TS954IDT datasheet PDF is available through the manufacturer’s product-datasheet link on this page. The document covers the TS951, TS952 and TS954 family and describes their input/output rail-to-rail BiCMOS architecture, low-power operation, and 3 V and 5 V optimization. Use the manufacturer PDF for final pin assignments, electrical limits, ordering information, and application guidance.
Where is the TS954IDT pinout?
The TS954IDT pinout is shown in the package diagram on this page and documented in the manufacturer’s TS954 family datasheet. The device uses a 14-pin SOIC package containing four rail-to-rail operational-amplifier channels. Verify each amplifier’s input, output, supply, and ground connection against the datasheet pin-description table before assigning PCB tracks or assembling a replacement board.
What are the key specifications of TS954IDT that engineers should know?
The TS954IDT integrates four input/output rail-to-rail BiCMOS amplifier channels in a 14-pin SOIC package. According to the STMicroelectronics family datasheet, its 2.7 V to 12 V supply range is optimized for 3 V and 5 V operation, while the low-power design targets compact analog systems. The principal design points are rail-to-rail input and output behavior, four channels per package, and a -40 °C to +125 °C operating-temperature range.
Is TS954IDT suitable for 3 V and 5 V applications?
Yes, the TS954IDT is specifically optimized and fully specified for 3 V and 5 V operation. The STMicroelectronics TS951, TS952 and TS954 family datasheet describes a 2.7 V minimum and 12 V maximum supply-voltage range. Its rail-to-rail input and output characteristics are useful when the signal can occupy much of the available supply range, although output load and slew-rate requirements must still be checked.
Where can I buy TS954IDT online?
Use the Request a Quote form on this page to request TS954IDT availability, current lead time, and order quantities. The form is the appropriate purchasing channel for a quote-based electronic-component order and lets the request include the exact TS954IDT suffix and delivery requirements. The manufacturer’s TS954 family datasheet should be consulted for package, temperature, and ordering-code requirements before submission.
What is the price of TS954IDT?
Submit a Request a Quote on this page for the current TS954IDT price and quantity schedule. The commercial quote should identify the exact 14-pin SOIC ordering code, required quantity, and destination. Electronic-component pricing can change with quantity, availability, and market conditions, so use the quote response for purchasing rather than relying on a historical or third-party listing.
What is the lead time for TS954IDT?
Request the current TS954IDT lead time through the Request a Quote form on this page. Include your required quantity, production schedule, and shipment destination so the quotation can reflect the appropriate supply conditions. The STMicroelectronics family datasheet identifies the device as a 14-pin SOIC general-purpose quad amplifier, but it does not establish a current customer-specific delivery commitment.
Is TS954IDT in stock?
Current TS954IDT stock should be confirmed through the Request a Quote form on this page. Provide the exact MPN TS954IDT, quantity, and delivery location to obtain a current availability response. Because stock levels and lead times can change, a successful quotation or order confirmation is more reliable than a general product-page inventory statement.
What is the best drop-in replacement for TS954IDT?
The closest identified drop-in candidates are the same-package TS924IDT, TS934IDT, and TS932IDT devices. All three are STMicroelectronics low-power amplifier-family choices associated with the 14-pin SO configuration, but their channel characteristics and electrical limits must be reviewed against the TS954IDT. The manufacturer datasheets should be compared for bandwidth, slew rate, output current, noise, distortion, and stability before substitution.
Can TS924IDT replace TS954IDT?
TS924IDT is a potential same-package replacement for TS954IDT, but final qualification depends on the application. Both are STMicroelectronics 14-pin SO-family low-power operational-amplifier devices with a 2.7 V to 12 V supply range. Compare the complete manufacturer specifications for each channel, particularly input bias current, output drive, bandwidth, slew rate, noise, distortion, and capacitive-load behavior.
When should I choose TS954IDT over TS924IDT?
Choose the TS954IDT when the design specifically depends on its input/output rail-to-rail BiCMOS performance or channel characteristics, while retaining the same 14-pin SO footprint. Choose TS924IDT only after its manufacturer datasheet demonstrates that its noise, distortion, bandwidth, output drive, and stability meet the signal chain requirements. Both parts use a 2.7 V to 12 V supply range, so voltage compatibility alone does not establish functional equivalence.
TS954IDT vs TS954ID — which package should I select?
TS954IDT is the tape-and-reel ordering form identified by the “T” suffix, while TS954ID identifies the device without that packing suffix. The functional amplifier device is the same; assembly packaging differs. When replacing an existing part, verify the manufacturer ordering table, package drawing, lead finish, and reel orientation so the incoming component matches the PCB assembly process.
What can replace TS954IDT?
TS924IDT, TS934IDT, and TS932IDT are the identified same-manufacturer 14-pin SO drop-in candidates for TS954IDT. They offer useful family alternatives, but no alternative should be treated as an automatic substitute because gain bandwidth, slew rate, output current, noise, distortion, and stability can differ. Validate the replacement against the complete signal-chain requirements in the relevant manufacturer datasheets.
Is TS954IDT the same as TS954IYDT?
No, TS954IDT and TS954IYDT have different order codes and should not be treated as identical without reviewing the manufacturer ordering information. The comparison identifies a shared TS954 family and a 14-pin SO package, but the suffix can indicate different temperature grade, automotive qualification, or production configuration. Confirm the exact ordering code and qualification requirements before substituting one for the other.

工程参考数据: TS954IDT ——对比、设计指导和合规信息。

选型指南

Choose the TS954IDT when a design needs four independent, input/output rail-to-rail amplifier channels in a 14-pin SOIC and operates from 2.7 V to 12 V, particularly in 3 V or 5 V systems. Its consolidated quad-channel package is useful when board area, component count, or matched analog-channel behavior matters. Choose TS924IDT when its specific input-bias, noise, bandwidth, distortion, and output-drive characteristics better fit the signal chain, after confirming its complete manufacturer specifications. Choose TS934IDT when its channel performance offers a closer functional match while preserving the same package. Choose TS932IDT when its output drive or noise behavior is better suited to the load. None of these alternatives should be substituted solely because the package matches; verify common-mode range, output swing, gain-bandwidth product, slew rate, output current, noise, distortion, and capacitive-load stability.

与替代料对比

参数 本产品 TS924IDT TS934IDT TS932IDT
Package SOIC-14 SOIC-14 - same package SOIC-14 - same package SOIC-14 - same package
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Amplifier Count 4 circuits 4 circuits 4 circuits 4 circuits
Minimum Supply Voltage 2.7 V 2.7 V 2.7 V 2.7 V
Maximum Supply Voltage 12 V 12 V 12 V 12 V
Special Features Input/output rail-to-rail, low power Low-power operational-amplifier family Low-power operational-amplifier family Low-power operational-amplifier family

关键差异点

  • Four rail-to-rail channels in one 14-pin package (对比 TS924IDT)
  • Rail-to-rail input and output operation (对比 TS934IDT)
  • Optimized low-voltage family positioning (对比 TS932IDT)

设计说明

Place the supply bypass capacitors immediately between the TS954IDT supply pins and ground reference, and connect them to the quiet ground plane rather than routing the return through noisy analog signal paths. Use short traces and a continuous ground reference beneath the 14-pin SOIC where practical. Because the device contains four amplifiers, inspect each channel’s feedback network and output route independently so one channel’s switching or high-current load does not disturb the other three.

Do not assume that rail-to-rail input and output operation permits every signal at either supply rail. Check the manufacturer’s common-mode and output-swing limits at the selected 2.7 V to 12 V supply voltage, and include input and output headroom in amplifier calculations. Also check the capacitive load presented by the next stage; a long cable, ADC input, or isolated network can reduce stability even when the resistive load is acceptable.

For low-level sensor signals, keep input traces short and route them away from switching-regulator outputs, relay contacts, inductors, and high-current return paths. Use a continuous reference plane and place passive gain or filter components close to the associated amplifier channel. When evaluating noise or distortion, reproduce the actual source impedance, gain setting, supply arrangement, and output load because changing any of these conditions can materially alter measured performance.

Confirm that each channel’s quiescent current and load current remain within the device power limits under worst-case supply voltage and temperature. Four active channels multiply the aggregate supply demand, and output-current consumption increases with output swing and load. Estimate the total dissipation from the actual supply and output currents, then ensure the PCB copper area and surrounding thermal environment can accommodate the resulting temperature rise without affecting adjacent precision circuitry.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The manufacturer TS954 family datasheet does not establish the requested environmental, automotive, halogen-free, or conflict-minerals declarations. These fields require confirmation from the current manufacturer product page or a formal declaration.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

TS954IDT datasheet TS954IDT pinout TS954IDT datasheet pdf TS954IDT specifications TS954IDT SOIC-14 amplifier TS954IDT rail-to-rail op amp TS954IDT 2.7V 12V STMicroelectronics TS954IDT TS954IDT equivalent TS954IDT replacement TS954IDT vs TS924IDT TS954IDT application circuit TS954IDT price TS954IDT stock TS954IDT footprint

相关元器件 & 术语

STMicroelectronics TS954IDT TS924IDT TS934IDT TS932IDT TS974IDT quad operational amplifier operational amplifier amplifier IC input/output rail-to-rail amplifier BiCMOS low-power amplifier rail-to-rail input rail-to-rail output common-mode range gain bandwidth slew rate output current low noise low distortion SOIC-14 SOIC package surface-mount package sensor signal conditioning active filtering
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情