TS954IDT - Quad Rail-to-Rail Low-Power Op Amp | STMicroelectronics
MPN: TS954IDT ✓ نشطTS954IDT نظرة عامة
An operational amplifier is an analog signal-conditioning semiconductor that compares two input voltages and amplifies the difference between them. A quad operational amplifier contains four independent amplifier channels in one package. The rail-to-rail BiCMOS category combines complementary bipolar input characteristics with CMOS output stages, while the low-power design targets portable and space-constrained applications.
The TS954IDT provides four rail-to-rail amplifier channels, low-noise input behavior, low distortion, and operation from 2.7 V to 12 V. The manufacturer describes the family as optimized and fully specified for 3 V and 5 V systems. Rail-to-rail input operation improves usable input range, while rail-to-rail output capability allows output voltage to approach the available supply voltage more closely than a conventional non-rail-to-rail output amplifier.
The TS954 family combines four general-purpose amplifiers with a 14-pin SO package. It is intended for applications where several independent analog channels are required, including sensor conditioning, buffer amplification, active filtering, low-level signal processing, and embedded control systems. The shared package consolidates four channels without requiring four separate amplifier packages, reducing board-area requirements.
Typical uses include portable measurement equipment, industrial sensor interfaces, audio and communications signal conditioning, battery-powered instruments, and general-purpose analog subsystems. The 2.7 V minimum supply supports 3 V systems, while the 12 V maximum provides flexibility for 5 V and higher-voltage designs when the applied operating point remains within the device ratings.
When designing around the TS954IDT, verify input and output common-mode limits, output-current demand, capacitive-load stability, and supply voltage for every channel. Decoupling capacitors should be placed close to the supply pins, and sensitive analog traces should be routed away from switching nodes and high-current return paths to preserve low-noise operation.
This product page combines the manufacturer datasheet information with practical application guidance, package details, technical comparisons, and drop-in replacement options. It is intended to help engineers select the correct amplifier, plan the PCB, and assess whether a same-package alternative can simplify an existing design without unnecessary board changes.
بدائل مباشرة لـ TS954IDT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع TS954IDT (نفس عامل الشكل والبصمة) — يختلف في Package, Gain-Bandwidth Product, Input Bias Current, Number of Amplifiers, Output Swing.
TS924IDT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS934IDT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS932IDT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS954IDT الحدود القصوى والخصائص الكهربائية
| Amplifier Count | 4 circuits |
| Product Type | Input/output rail-to-rail low-power operational amplifier |
| Process Technology | BiCMOS |
| Minimum Supply Voltage | 2.7 V |
| Maximum Supply Voltage | 12 V |
| Optimized Supply Voltage | 3 V and 5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| نطاق درجة حرارة التشغيل | -40 °C to +125 °C |
| العلبة | 14-pin SOIC |
| نوع التركيب | Surface mount |
| Amplifier Classification | Standard general-purpose amplifier |
| Distortion | 0.01% |
| Input Type | Rail-to-rail |
| نوع الخرج | Rail-to-rail |
| Power Class | Low power |
تكوين أطراف TS954IDT
| دبوس 1 | OUT1 — Operational amplifier 1 output |
| دبوس 2 | -IN1 — Operational amplifier 1 inverting input |
| دبوس 3 | +IN1 — Operational amplifier 1 non-inverting input |
| دبوس 4 | VCC — Positive supply voltage |
| دبوس 5 | +IN2 — Operational amplifier 2 non-inverting input |
| دبوس 6 | -IN2 — Operational amplifier 2 inverting input |
| دبوس 7 | OUT2 — Operational amplifier 2 output |
| دبوس 8 | OUT3 — Operational amplifier 3 output |
| دبوس 9 | -IN3 — Operational amplifier 3 inverting input |
| دبوس 10 | +IN3 — Operational amplifier 3 non-inverting input |
| دبوس 11 | VCC — Positive supply voltage |
| دبوس 12 | -IN4 — Operational amplifier 4 inverting input |
| دبوس 13 | +IN4 — Operational amplifier 4 non-inverting input |
| دبوس 14 | OUT4 — Operational amplifier 4 output |
التطبيقات النموذجية
TS954IDT مناسب لـ 6 التطبيقs: Portable Sensor Signal Conditioning, Industrial Sensor Interface, Low-Voltage Audio Preamplifier, Active Filtering and Buffering, Battery-Powered Measurement Instrument, Communications Signal Conditioning.
Portable Sensor Signal Conditioning
The TS954IDT fits portable measurement systems that need several low-voltage analog channels without allocating space for four individual amplifier packages. Its four input/output rail-to-rail BiCMOS channels operate from 2.7 V to 12 V, allowing the same device family to serve 3 V and 5 V designs. Use the channels to amplify weak sensor outputs, buffer high-impedance sources, and provide gain before an ADC. The low-power architecture is particularly useful in battery-operated instruments, while the -40 °C to +125 °C range supports industrial ambient conditions. Validate each channel’s common-mode range and output swing against the sensor’s operating envelope.
موصى به
Industrial Sensor Interface
The TS954IDT can condition several low-level industrial sensor signals in one 14-pin SOIC package. Rail-to-rail inputs help preserve signal information when the input level moves close to either supply rail, while rail-to-rail outputs improve the available output range in 3 V and 5 V systems. Common uses include transducer amplifiers, current-loop interfaces, resistance measurement, and sensor-to-ADC driver stages. Keep the amplifier close to the sensor connector to minimize noise pickup, and verify the TS954’s maximum output-current capability for the ADC input and termination network.
موصى به
Low-Voltage Audio Preamplifier
The TS954IDT’s four rail-to-rail amplifier channels are suitable for small-signal audio preamplification in compact, low-voltage equipment. Each channel can provide voltage gain before a line-level stage, while the 2.7 V to 12 V supply range covers 3 V and 5 V portable audio architectures. The family datasheet identifies low distortion and low-noise behavior as important characteristics for this device class. Place the TS954 near the source connector, use short low-impedance signal paths, and confirm the selected channel’s bandwidth and output-current capability for the following audio stage.
موصى به
Active Filtering and Buffering
The quad TS954IDT supports parallel active-filter and buffer stages in 3 V or 5 V analog systems. Four channels allow several stages to be implemented with one package, reducing component count and simplifying power distribution. Its rail-to-rail input and output characteristics are useful for filters whose signal occupies a large portion of the supply range, while the low-power BiCMOS design supports compact control and monitoring equipment. Determine each filter’s stability and noise performance at the actual source and load impedances, and place passive filter components close to the associated amplifier pins.
موصى به
Battery-Powered Measurement Instrument
The TS954IDT is appropriate for battery-powered measurement equipment requiring four low-voltage amplifier channels in a compact footprint. Its 2.7 V minimum supply supports 3 V systems, and the manufacturer family is optimized and fully specified for 3 V and 5 V operation. The channels can condition thermocouple, resistive, current, or low-level voltage inputs before conversion. Rail-to-rail behavior helps maximize usable signal range, but low-current operation still requires attention to quiescent current, output-current demand, and the voltage headroom lost in long-divider or gain networks.
موصى به
Communications Signal Conditioning
The TS954IDT can provide local amplification and buffering for communications and control signals in compact 3 V or 5 V equipment. Four channels support receiver-side filtering, threshold amplification, line-driver interfacing, and decoupling of sensitive analog stages. Rail-to-rail input behavior is useful when signals span much of the available supply range, and the low-power BiCMOS architecture can simplify portable terminal design. Check the required gain-bandwidth product, slew rate, output-current capability, and capacitive-load stability at the actual line impedance before using a channel as a cable driver.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TS954IDT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TS924IDT | TS934IDT | TS932IDT |
|---|---|---|---|---|
| Package | SOIC-14 | SOIC-14 - same package | SOIC-14 - same package | SOIC-14 - same package |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Minimum Supply Voltage | 2.7 V | 2.7 V | 2.7 V | 2.7 V |
| Maximum Supply Voltage | 12 V | 12 V | 12 V | 12 V |
| Special Features | Input/output rail-to-rail, low power | Low-power operational-amplifier family | Low-power operational-amplifier family | Low-power operational-amplifier family |
أبرز الفروقات
- Four rail-to-rail channels in one 14-pin package (مقابلTS924IDT)
- Rail-to-rail input and output operation (مقابلTS934IDT)
- Optimized low-voltage family positioning (مقابلTS932IDT)
ملاحظات التصميم
Place the supply bypass capacitors immediately between the TS954IDT supply pins and ground reference, and connect them to the quiet ground plane rather than routing the return through noisy analog signal paths. Use short traces and a continuous ground reference beneath the 14-pin SOIC where practical. Because the device contains four amplifiers, inspect each channel’s feedback network and output route independently so one channel’s switching or high-current load does not disturb the other three.
Do not assume that rail-to-rail input and output operation permits every signal at either supply rail. Check the manufacturer’s common-mode and output-swing limits at the selected 2.7 V to 12 V supply voltage, and include input and output headroom in amplifier calculations. Also check the capacitive load presented by the next stage; a long cable, ADC input, or isolated network can reduce stability even when the resistive load is acceptable.
For low-level sensor signals, keep input traces short and route them away from switching-regulator outputs, relay contacts, inductors, and high-current return paths. Use a continuous reference plane and place passive gain or filter components close to the associated amplifier channel. When evaluating noise or distortion, reproduce the actual source impedance, gain setting, supply arrangement, and output load because changing any of these conditions can materially alter measured performance.
Confirm that each channel’s quiescent current and load current remain within the device power limits under worst-case supply voltage and temperature. Four active channels multiply the aggregate supply demand, and output-current consumption increases with output swing and load. Estimate the total dissipation from the actual supply and output currents, then ensure the PCB copper area and surrounding thermal environment can accommodate the resulting temperature rise without affecting adjacent precision circuitry.
معلومات الامتثال
The manufacturer TS954 family datasheet does not establish the requested environmental, automotive, halogen-free, or conflict-minerals declarations. These fields require confirmation from the current manufacturer product page or a formal declaration.