TUSB1106RTZR - USB 2.0 Half-Speed Transceiver | TI
料号: TUSB1106RTZR ✓ 量产中TUSB1106RTZR 概述
A USB transceiver is an interface IC that translates logic-level data between a host or hub and a USB peripheral. It belongs to the USB interface transceiver class within the broader interface IC and semiconductor hierarchy. This dual-rate capability allows one device to support both full-speed and low-speed USB links, making it useful in peripheral controllers, portable equipment, industrial interfaces, and legacy USB connectivity designs.
The TUSB1106 is compliant with the Universal Serial Bus Specification Revision 2.0. Its principal data-rate ratings are 12 Mbit/s for full-speed operation and 1.5 Mbit/s for low-speed operation. The integrated 3.3 V regulator can be bypassed, giving the system designer a choice between using VBUS-derived power and controlling the regulator enable function. The 16-WQFN package supports compact surface-mount layouts while providing an exposed pad for improved board-level thermal performance.
Operation at both USB speed rates expands compatibility with USB peripherals that use full-speed or low-speed signaling. The half-speed transceiver architecture implements one transmit path and one receive path, while the integrated regulator reduces the number of external power-management functions required around a USB peripheral. Designers must still account for USB data-line impedance, ESD protection, connector routing, and the regulator bypass configuration in the system schematic.
Typical uses include USB-to-serial bridges, embedded USB peripherals, portable data-acquisition equipment, industrial control interfaces, and USB connectivity for legacy full-speed or low-speed devices. The compact 3 x 3 mm package is particularly useful when board area is constrained but a full USB interface is required without relying on a larger host-side controller.
For PCB implementation, route D+ and D+ as a controlled-impedance differential pair, connect the data lines according to the manufacturer's reference layout, and place ESD protection close to the connector. Decouple the 3.3 V output according to the device's recommended capacitor network and verify whether the integrated regulator should be bypassed for the selected power architecture.
This product page combines the manufacturer's USB 2.0 compliance information, exact package and temperature details, commercial sourcing guidance, and an analysis of same-footprint alternatives to support faster component selection and PCB design.
直接替换替代料: TUSB1106RTZR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TUSB1106RTZR (相同外形与封装尺寸) ——差异在于 Package, Product Type.
TUSB1105RTZRG4
✅ 直接替换📋 参考替代料(不在目录中)
TUSB1105RTZR
✅ 直接替换📋 参考替代料(不在目录中)
TUSB1105RGTR
✅ 直接替换联系询价
查看数据手册 →TUSB1106RTZR 规格参数
| Product Type | Half-speed USB 2.0 transceiver |
| USB Specification Compliance | Universal Serial Bus Specification Revision 2.0 |
| Full-Speed Data Rate | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s |
| Transmit Paths | 1 |
| Receive Paths | 1 |
| Integrated Regulator | 3.3 V bypassable voltage regulator |
| Regulator Power Source | USB VBUS |
| 封装 | 16-WQFN (RTZ), 3 x 3 mm |
| 引脚数量 | 16 pins |
| Exposed Pad | Present |
| 安装类型 | Surface mount |
| 工作温度范围 | -40 °C to +85 °C |
TUSB1106RTZR 16-wqfn (rtz), 3 x 3 mm 引脚配置指南
TUSB1106RTZR(16-wqfn (rtz), 3 x 3 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TUSB1106RTZR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TUSB1106RTZR 适用于 6 应用s: USB-to-Serial Peripheral Bridge, Industrial USB Control Interface, Portable USB Data Acquisition, USB Power-Management Interface, Legacy USB Peripheral Connectivity, USB Security and Access Device.
USB-to-Serial Peripheral Bridge
The TUSB1106RTZR fits a USB-to-serial bridge because it provides dedicated transmit and receive paths at both 12 Mbit/s full-speed and 1.5 Mbit/s low-speed rates. Place the transceiver between a host USB connector and a serial controller or bridge logic, using the integrated 3.3 V regulator when the downstream circuit can operate from USB VBUS. The dual-rate support broadens device compatibility without requiring separate full-speed and low-speed interface circuits. PCB implementation should preserve controlled-impedance D+ and D- routing and place connector ESD protection close to the external pins.
推荐
Industrial USB Control Interface
The TUSB1106RTZR is appropriate for an industrial controller that must interface with USB full-speed or low-speed service equipment. Its 12 Mbit/s and 1.5 Mbit/s operating modes provide a single interface for equipment using either USB rate, while the compact 3 x 3 mm WQFN footprint conserves board area. The bypassable 3.3 V regulator can simplify USB-powered operation, although an externally supplied rail may be preferable where the industrial system already regulates power. Follow the manufacturer's reference layout to keep the data pair away from switching nodes and high-current return paths.
推荐
Portable USB Data Acquisition
The TUSB1106RTZR can connect a portable data-acquisition unit to a USB host at either full-speed 12 Mbit/s or low-speed 1.5 Mbit/s. Its one-transmit, one-receive architecture suits compact sensor and control equipment, while the small 16-WQFN package leaves more board area for analog circuitry. When operating from a battery-powered portable design, the integrated 3.3 V regulator may be bypassed if the host VBUS supply is unsuitable. Confirm the permitted power topology, output-capacitor requirements, and data-line protection strategy in the design.
推荐
USB Power-Management Interface
The TUSB1106RTZR is useful in USB peripherals that need both data communication and a 3.3 V auxiliary supply from VBUS. Its integrated regulator supports 3.3 V operation and can be bypassed when another valid source supplies the device, giving the designer flexibility in the power architecture. This is especially helpful in compact peripheral designs where adding a separate regulator would increase component count. Verify bypass-state behavior, startup sequencing, and decoupling values against the manufacturer data sheet before finalizing the circuit.
推荐
Legacy USB Peripheral Connectivity
The TUSB1106RTZR supports peripherals that communicate at either 1.5 Mbit/s low-speed or 12 Mbit/s full-speed, making it suitable for legacy and mixed-speed USB equipment. A single device can therefore address both operating modes while retaining USB 2.0 compatibility. The WQFN package is compact, but the exposed pad and high-speed data routing still require careful PCB execution. Maintain a continuous reference plane under the pair, observe the recommended trace geometry, and place ESD protection at the connector rather than beside the transceiver.
推荐
USB Security and Access Device
The TUSB1106RTZR can serve as the USB interface in a compact access-control or security peripheral that enumerates as full-speed or low-speed equipment. Supporting both 12 Mbit/s and 1.5 Mbit/s rates permits compatibility with multiple host and peripheral configurations, while the integrated 3.3 V regulator may simplify VBUS-powered operation. Keep the USB pair isolated from noisy power-conversion stages and provide protection appropriate to the exposed connector environment. Review enable timing and bus-state behavior with the system firmware during startup and suspend transitions.
推荐
推荐产品汇总
工程参考数据: TUSB1106RTZR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TUSB1105RTZRG4 | TUSB1105RTZR | TUSB1105RGTR |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 16-WQFN (3x3) | 16-WQFN (3x3) | 16-WQFN (3x3) | 16-WQFN (3x3) |
| Product Type | Half-speed USB 2.0 transceiver | Half-speed USB 2.0 transceiver | Half-speed USB 2.0 transceiver | Half-speed USB 2.0 transceiver |
| USB Specification | USB 2.0 | USB 2.0 | USB 2.0 | USB 2.0 |
| Full-Speed Data Rate | 12 Mbit/s | 12 Mbit/s | 12 Mbit/s | 12 Mbit/s |
| Low-Speed Data Rate | 1.5 Mbit/s | 1.5 Mbit/s | 1.5 Mbit/s | 1.5 Mbit/s |
| Transmit and Receive Paths | 1 transmit, 1 receive | 1 transmit, 1 receive | 1 transmit, 1 receive | 1 transmit, 1 receive |
关键差异点
- Supports both principal USB half-speed operating rates (对比 TUSB1105RTZR)
- Combines USB data transfer with an integrated bypassable 3.3 V regulator (对比 TUSB1105RTZRG4)
- Compact exposed-pad package supports dense USB peripheral layouts (对比 TUSB1105RGTR)
设计说明
Route D+ and D- as a short, continuous differential pair using the geometry specified by the Texas Instruments TUSB1106 data sheet. Keep the pair over a continuous ground plane, minimize stubs and test-point breaks, and avoid routing it parallel to switching-node or high-current power traces. Place USB ESD protection beside the external connector so surge current is diverted before reaching the TUSB1106RTZR.
Select the regulator-bypass configuration early because it determines whether the TUSB1106RTZR's integrated 3.3 V regulator participates in the VBUS power path. Follow the manufacturer capacitor recommendations at the regulator output and verify startup behavior when the device transitions from bus-powered to externally powered operation. The exposed pad must be connected according to the package drawing and thermal-via guidance.
Do not treat a USB transceiver as interchangeable solely because its data rate and package dimensions match. Before substituting TUSB1105RTZRG4, TUSB1105RTZR, or TUSB1105RGTR, compare pull-up configuration, regulator-bypass logic, enable polarity, pin names, and exposed-pad requirements. Although the supported rate difference is 0 Mbit/s, a function-level difference can still prevent operation or alter bus-device detection.
合规信息
USB 2.0 compliance is confirmed by Texas Instruments. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals statuses are not established by the referenced product and distributor information.