Texas Instruments

TUSB9260PVP - USB 3.0 to SATA Bridge | TI Storage

料号: TUSB9260PVP ✗ 停产
1.1 V Vdss 64-pin HTQFP with exposed pad, 7 mm x 7 mm Package
最小起订量: 1 |

TUSB9260PVP 概述

The Texas Instruments TUSB9260PVP is a SuperSpeed USB 3.0 to Serial ATA bridge based on an ARM Cortex-M3 microcontroller. It connects a USB 3.0 host interface to a SATA storage device and supports 1.1 V, 1.8 V, and 3.3 V supply rails. The device is offered in a 64-pin HTQFP package with an exposed pad, measuring 7 mm by 7 mm.

A USB-to-SATA bridge is an interface controller that translates commands and data between a USB host and a Serial ATA drive. This USB 3.0-to-SATA bridge sits within the interface-controller and storage-connectivity hierarchy, allowing compatible storage equipment to use USB connectivity while retaining a SATA device interface. Its microcontroller-based implementation supports the command, data, and power-management functions needed for USB-attached storage.

The TUSB9260PVP provides SuperSpeed USB 3.0 operation together with USB 2.0 support, enabling it to serve as the storage interface in systems that need backward compatibility with slower USB links. The manufacturer identifies the product as a USB 3.0-to-Serial ATA bridge, while the component listing identifies the interface as an SPI serial interface with 1.1 V, 1.8 V, and 3.3 V supply options.

The TUSB9260 architecture combines an ARM Cortex-M3 microcontroller with dedicated USB-to-SATA bridge hardware and firmware support. This implementation is intended to provide the necessary protocol translation for USB-attached storage devices. Designers should allocate separate routing for high-speed USB and SATA signals, maintain continuous return-path references, and observe the exposed-pad requirements of the HTQFP package.

Typical uses include external storage enclosures, USB-to-SATA adapters, backup appliances, and industrial data-acquisition systems that require an established USB 3.0 host connection to a SATA drive. The device can also serve in equipment where a legacy SATA storage interface must remain accessible through a newer USB-facing system architecture.

Layout quality is central to reliable SuperSpeed operation. Place differential USB and SATA pairs over continuous ground planes, use short matched routing, minimize stub lengths, and provide low-impedance power distribution for 1.1 V, 1.8 V, and 3.3 V rails. Follow the manufacturer pin-description table and layout guidance when assigning tracks and connecting the exposed thermal pad.

This product page combines the exact package, supply, interface, and lifecycle characteristics with a design-focused comparison against TUSB9261PVP. It also identifies practical implementation considerations for USB 3.0-to-SATA storage products and distinguishes documented pin-compatible upgrades from alternatives requiring broader hardware validation.

直接替换替代料: TUSB9260PVP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: TUSB9260PVP (相同外形与封装尺寸) ——差异在于 Product Type.

Texas Instruments
Product Type: USB 3.0 to Serial ATA bridge
对比 TUSB9260PVP →

TUSB9261PVP

✅ 直接替换
Texas Instruments
📦 64-HTQFP (7x7)
USB 3.0 to Serial ATA bridge · Second-generation SuperSpeed USB · 5 Gbps · 1.5 Gbps or 3.0 Gbps · ARM Cortex-M3 microcontroller · USB Attached SCSI Protocol (UASP) · 3 V to 3.6 V · 64-lead HTQFP

联系询价

查看数据手册 →

TUSB9260PVP 规格参数

Product Type SuperSpeed USB 3.0 to Serial ATA bridge
Controller Core ARM Cortex-M3 microcontroller
USB Interface USB 3.0 SuperSpeed with USB 2.0 support
Storage Interface Serial ATA bridge
SPI Serial Interface Supported
Low Supply Voltage 1.1 V
Intermediate Supply Voltage 1.8 V
High Supply Voltage 3.3 V
封装 64-pin HTQFP with exposed pad, 7 mm x 7 mm
安装类型 Surface mount
Packaging Tray
Product Status Not for new designs
Primary Application Hard drive interface and USB-attached storage

TUSB9260PVP 64-pin htqfp with exposed pad, 7 mm x 7 mm 引脚配置指南

TUSB9260PVP(64-pin htqfp with exposed pad, 7 mm x 7 mm 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

TUSB9260PVP 的 64-pin htqfp with exposed pad, 7 mm x 7 mm 封装引脚图

暂无详细引脚数据: TUSB9260PVP.

请参阅 数据手册 以查看完整引脚配置。

典型应用

TUSB9260PVP 适用于 6 应用s: USB-to-SATA External Storage Enclosures, USB 3.0 Hard Drive Adapters, Portable Backup Appliances, Industrial Storage Gateways, Secure Data Acquisition Systems, Legacy SATA Equipment Refresh.

🖥️

USB-to-SATA External Storage Enclosures

The TUSB9260PVP is a USB 3.0-to-SATA bridge.

💾

USB 3.0 Hard Drive Adapters

The TUSB9260PVP translates between USB 3.0 and Serial ATA.

📱

Portable Backup Appliances

The TUSB9260PVP supports portable USB storage systems.

🏭

Industrial Storage Gateways

The TUSB9260PVP bridges industrial USB hosts and SATA storage.

🔧

Secure Data Acquisition Systems

The TUSB9260PVP links USB acquisition hosts with SATA media.

🌐

Legacy SATA Equipment Refresh

The TUSB9260PVP adds a USB-facing path for SATA equipment.

What is the TUSB9260PVP?
The TUSB9260PVP is a Texas Instruments SuperSpeed USB 3.0 to Serial ATA bridge built around an ARM Cortex-M3 microcontroller. It translates between a USB host and a SATA storage device and supports USB 2.0 as well as USB 3.0 operation. According to the Texas Instruments product page, the device is intended for USB-attached storage systems, and the component is packaged in a 64-pin HTQFP with an exposed pad.
What package does the TUSB9260PVP use?
The TUSB9260PVP uses a 64-pin HTQFP package with an exposed pad measuring 7 mm by 7 mm. The exposed pad is part of the thermal and electrical design, so its connection and land pattern must follow the manufacturer package drawing. According to the Texas Instruments product documentation, the device is supplied in a tray. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
What supply voltages does the TUSB9260PVP support?
The TUSB9260PVP supports 1.1 V, 1.8 V, and 3.3 V supply rails. These values identify the internal operating rails that the power system must support for the bridge and its associated interfaces. According to the Texas Instruments TUSB9260 documentation, the device is a USB 3.0-to-SATA bridge; the exact rail sequence, decoupling values, and tolerance limits should be taken from the manufacturer power-supply guidance.
Does the TUSB9260PVP support USB 2.0?
Yes, the TUSB9260PVP supports USB 2.0 in addition to SuperSpeed USB 3.0 operation. This dual-generation support makes the bridge suitable for storage products intended to connect through either a 5 Gb/s USB 3.0 link or a slower USB 2.0 link. According to the Texas Instruments product page, the component is a USB 3.0-to-SATA bridge, while the product listings identify USB 2.0 and USB 3.0 support.
What applications use the TUSB9260PVP?
The TUSB9260PVP fits USB-to-SATA storage adapters, external drive enclosures, backup appliances, and industrial storage gateways. Its USB-facing side allows a host computer to access a SATA device through a USB connection, while the microcontroller-based bridge handles protocol translation. According to the Texas Instruments description, the device provides the hardware and firmware foundation required for USB-attached storage, with supply rails of 1.1 V, 1.8 V, and 3.3 V.
Is the TUSB9260PVP suitable for hard-drive interfaces?
Yes, the TUSB9260PVP is specifically identified for hard-drive interface applications. It provides the bridge between a USB 3.0 or USB 2.0 host and a Serial ATA device, making it appropriate for external storage and backup systems. The device also exposes an SPI serial interface. According to the Texas Instruments product page, the TUSB9260 is a SuperSpeed USB 3.0 to Serial ATA bridge.
Where can I find the TUSB9260PVP datasheet and pinout?
The official TUSB9260 datasheet and support information are available through the Texas Instruments product page at https://www.ti.com/product/TUSB9260. The package is a 64-pin HTQFP with an exposed pad, and the pin-description table in the manufacturer datasheet is the authoritative source for signal names and pin assignments. Use that table together with the recommended layout when implementing the USB and SATA connections.
Can TUSB9261PVP replace TUSB9260PVP on the same PCB?
Yes, the Texas Instruments TUSB9260 product page identifies a pin-to-pin replacement that complies with newer USB specifications. The replacement MPN is TUSB9261PVP, which is also identified as a 64-pin HTQFP device. This means the package and pin assignment can remain unchanged, while firmware, host compatibility, and USB compliance should still be validated before production use.
What is the difference between TUSB9260PVP and TUSB9261PVP?
The principal documented difference is USB specification compliance: Texas Instruments describes the replacement as pin-to-pin compatible with the TUSB9260 and compliant with newer USB specifications. Both products use the 64-pin HTQFP format, so no package migration is required. Before substitution, confirm the target USB host, device firmware, cable requirement, and qualification status for the specific production configuration.
When should I choose TUSB9260PVP instead of TUSB9261PVP?
Choose TUSB9260PVP when maintaining an already qualified USB 3.0-to-SATA design and its associated firmware is more important than adopting newer USB specification compliance. Choose TUSB9261PVP for new or updated products when the manufacturer identifies it as the pin-to-pin, newer-specification-compliant replacement. Because TUSB9260PVP is listed as not for new designs, confirm lifecycle requirements before committing an unchanged platform.
Is the TUSB9260PVP still suitable for new designs?
The TUSB9260PVP is listed as not for new designs, so it is best suited to maintaining an existing qualified design rather than starting a new platform. The listed lifecycle status is NRND, which normally indicates that the part remains available for existing use while new production adoption is discouraged. For a new USB-to-SATA product, review TUSB9261PVP as the documented pin-to-pin replacement.
Where can I buy the TUSB9260PVP and check its lead time?
Use the Request a Quote form on this page to ask about TUSB9260PVP ordering, current stock, manufacturer lead time, and quantity requirements. The component listing identifies tray packaging, but no fixed customer lead time should be assumed. Because the device is marked not for new designs, include your target quantity, date code requirements, and whether the order is for maintenance or new production.
What is the current availability of TUSB9260PVP?
Current inventory should be confirmed through the Request a Quote form on this page rather than assumed from an indexed listing. The TUSB9260PVP is identified as not for new designs, so supply may be constrained relative to active components. Submit the required quantity and tray-packaging expectations with your request, and specify whether traceability or date-code control is necessary for the application.
How should the TUSB9260PVP PCB be laid out?
Route the USB and SATA differential pairs over uninterrupted reference planes, keep the paths short and matched, and avoid unnecessary stubs or plane changes. Provide low-impedance distribution for the 1.1 V, 1.8 V, and 3.3 V rails and connect the HTQFP exposed pad as specified by the manufacturer land pattern. According to Texas Instruments application guidance, signal integrity and power delivery are central to reliable SuperSpeed USB operation.
What are the key specifications of TUSB9260PVP that engineers should know?
The key TUSB9260PVP characteristics are its USB 3.0-to-SATA function, ARM Cortex-M3 controller core, USB 2.0 compatibility, and support for 1.1 V, 1.8 V, and 3.3 V supply rails. It is packaged in a 64-pin HTQFP with an exposed pad measuring 7 mm by 7 mm. The manufacturer also lists a 64-pin tray configuration and identifies the device as a hard-drive interface component.

工程参考数据: TUSB9260PVP ——对比、设计指导和合规信息。

选型指南

Choose TUSB9260PVP when maintaining an existing USB-to-SATA design whose firmware, enclosure, and host compatibility have already been qualified. Its USB 3.0 and USB 2.0 support, 1.1 V, 1.8 V, and 3.3 V rails, and 64-pin HTQFP footprint fit established storage-adapter platforms. The device is listed as not for new designs, so new programs should normally evaluate TUSB9261PVP. Select TUSB9261PVP when the manufacturer-documented pin-to-pin replacement and newer USB specification compliance are priorities; its same package permits PCB reuse, but firmware and host validation remain necessary. No other drop-in replacement is identified, so changing to a different bridge family should be treated as a redesign rather than a substitution.

与替代料对比

参数 本产品 TUSB9261PVP
Brand Texas Instruments Texas Instruments
Package 64-HTQFP (7x7) with exposed pad 64-HTQFP (7x7)
Product Function SuperSpeed USB 3.0 to Serial ATA bridge USB-to-SATA bridge with newer USB specification compliance
USB Version Support USB 3.0 and USB 2.0 Newer USB specification compliance
Mounting Type Surface mount Surface mount

关键差异点

  • Direct pin-to-pin upgrade path (对比 TUSB9261PVP)
  • Integrated USB 2.0 and USB 3.0 support (对比 TUSB9261PVP)
  • Microcontroller-based protocol conversion (对比 TUSB9261PVP)

设计说明

Route USB and SATA differential pairs over continuous ground references, maintain length matching where the interface specification requires it, and remove unnecessary pads, test points, and stubs. Place decoupling and interface-support components close to their associated pins. SuperSpeed links are sensitive to discontinuities and reference-plane changes, so validate the final stack-up and controlled-impedance geometry with the PCB fabricator.

Design the power tree for 1.1 V, 1.8 V, and 3.3 V rails with low-impedance planes or wide traces and local bulk and high-frequency decoupling at the bridge. Use the manufacturer power-supply sequence and voltage tolerances to determine startup order and capacitor selection. Avoid sharing narrow supply paths with unrelated noisy loads, particularly when the enclosure contains motor, fan, or display circuitry.

Connect the exposed pad through the package land pattern to a ground plane using the thermal-via arrangement specified by the manufacturer. Estimate junction temperature from ambient temperature, package dissipation, and the board-dependent thermal resistance rather than assuming an unlimited heat path. Check the exposed-pad soldering process and coplanarity because voiding beneath the pad can increase junction temperature and reduce long-term reliability.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated in the cited product records. Confirm the applicable declarations with Texas Instruments for the ordered device and package.

数据核验日期: 2026-11-10 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

TUSB9260PVP TUSB9260PVP datasheet TUSB9260PVP datasheet pdf TUSB9260PVP pinout TUSB9260PVP schematic TUSB9260PVP equivalent TUSB9260PVP replacement TUSB9260PVP cross reference TUSB9260PVP vs TUSB9261PVP TUSB9260PVP footprint Texas Instruments TUSB9260PVP TUSB9260 64 HTQFP pinout TUSB9260 USB to SATA application circuit TUSB9260PVP price TUSB9260PVP stock

相关元器件 & 术语

Texas Instruments TUSB9260PVP TUSB9260 TUSB9261PVP USB 3.0 SuperSpeed USB USB 2.0 Serial ATA SATA bridge USB-to-SATA bridge ARM Cortex-M3 interface controller storage interface SPI serial interface 64-pin HTQFP HTQFP package family QFP family surface-mount package exposed pad 1.1 V 1.8 V 3.3 V hard-drive interface external storage enclosure USB-attached storage
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情