WM1800CGEFL/V - 32-QFN Audio Codec IC, Sigma-Delta | Cirrus Logic
料号: WM1800CGEFL/V ✗ 停产WM1800CGEFL/V 概述
An audio codec is a mixed-signal integrated circuit that translates between digital audio data streams and analog audio voltages. It sits inside the wider semiconductor hierarchy as a mixed-signal IC, more specifically a codec, and it usually pairs one or more analog-to-digital converters with one or more digital-to-analog converters plus the digital interface logic needed to move audio frames to and from a host processor. Because the codec performs both conversion directions on the same die, it saves board area and simplifies the analog signal chain around it.
Key characteristics of the WM1800CGEFL/V include its 32-pin QFN-32 footprint, the compact 5 x 5 x 0.9 mm body, and the sigma-delta conversion topology identified in the component listings. The part is offered in a tested condition for industrial and repair-grade sourcing, and the /V ordering suffix corresponds to tube packaging while the /RV suffix denotes the tape-and-reel presentation of the same device. RoHS status is listed inconsistently across supply-chain listings, with some entries marked compliant and others marked not compliant, so the declaration should be confirmed against the specific lot paperwork before use in a certified build.
Technically the device integrates its converters, reference and interface circuitry into a single no-lead QFN. QFN construction means there are no protruding gull-wing leads, so the part cannot be hand-soldered and is placed by pick-and-place with a bottom-side thermal and ground land pattern. The published listings confirm a sigma-delta converter architecture, which is the standard choice for high-resolution audio because it pushes the quantisation noise out of band where it is removed by the digital decimation filters.
Typical uses include portable and personal-audio equipment, headset and docking-station interfaces, USB audio accessories, compact consumer audio appliances and equipment-repair and legacy-platform builds where an original audio codec has to be replaced without redesigning the printed circuit board. In each case the codec sits between an analog microphone or line input and a digital audio bus, or between a digital stream and an analog headphone or line output.
The main design consideration is that this is a mature catalog part from the Wolfson Microelectronics range, so engineers should confirm the exact pin assignment, supply rails, converter resolution and clocking requirements from the manufacturer datasheet before committing to a design, and should verify that the surrounding decoupling and grounding topology matches the reference circuit for the specific variant. Because the package is QFN-32 with a bottom thermal land, board-level copper must be adequate for the dissipation of the codec in a densely packed portable product.
This page combines distributor catalogue data, ordering-code analysis, drop-in ordering options and practical integration notes for the WM1800CGEFL/V in a single place, giving engineers sourcing and design information beyond the short catalogue entry.
直接替换替代料: WM1800CGEFL/V ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
WM1800CGEFL/RV
✅ 直接替换📋 参考替代料(不在目录中)
WM1800CGEFL
✅ 直接替换📋 参考替代料(不在目录中)
WM1800GEFL
✅ 直接替换📋 参考替代料(不在目录中)
WM1800CGEFL/V 最大额定值与电气特性
| Device Type | Audio codec (mixed-signal IC) |
| Manufacturer | Wolfson Microelectronics (Cirrus Logic) |
| 分类 | Analog & Mixed Signal / CODECs |
| 封装 | QFN-32, 5 x 5 x 0.9 mm |
| 引脚数量 | 32 pins |
| 安装类型 | Surface mount (no-lead QFN) |
| Converter Architecture | Sigma-delta |
| Condition | Tested |
| Packing Option (/V suffix) | Tube |
| 生命周期状态 | Legacy catalog part, currently offered through tested/surplus distribution channels |
WM1800CGEFL/V qfn-32, 5 x 5 x 0.9 mm 引脚配置指南
WM1800CGEFL/V(qfn-32, 5 x 5 x 0.9 mm 封装)的引脚配置。 该数字 IC 包含 GPIO、通信接口(UART、SPI、I2C)和电源引脚。请参阅制造商数据手册以了解复用引脚功能和配置选项。对嵌入式系统设计和 PCB 布局至关重要。
暂无详细引脚数据: WM1800CGEFL/V.
请参阅 数据手册 以查看完整引脚配置。
典型应用
WM1800CGEFL/V 适用于 6 应用s: Portable USB Audio Dongles, Headset and Earbud Interface Boards, Docking Stations and Speakerphone Cradles, Legacy Equipment Repair and Replacement, Digital-to-Analog Line Output Modules, IoT Voice Front-Ends.
Portable USB Audio Dongles
The WM1800CGEFL/V fits compact USB audio dongles where a single 32-pin QFN package has to provide both analog capture and analog playback around a USB audio controller. Integrating the conversion stages in one 5 x 5 x 0.9 mm no-lead body keeps the analog footprint small and the bill of materials short, which matters when the dongle housing is only a few millimetres above the PCB. The sigma-delta architecture listed for this family suits the high-resolution playback paths typical of these adapters. During layout, reserve the bottom land as the ground and thermal connection of the QFN and keep the microphone and output coupling paths away from the digital interface nets. Because this is a legacy catalog device, verify the exact clocking scheme, supply rails and audio interface format from the manufacturer datasheet for the ordering code before the first board revision.
推荐
Headset and Earbud Interface Boards
In headset, gaming headset and earbud accessory designs, the WM1800CGEFL/V provides the bridge between a digital audio link and the analog microphone plus headphone drive path. Its 32-pin QFN package allows the codec, amplifier and connector to be placed on the same side of a slim flex board, and the single-device codec arrangement reduces the number of high-speed analog routing transitions compared with discrete converters. The published sigma-delta conversion topology is appropriate for the wide dynamic range expected of voice-chat and music playback in these products. Keep the analog ground and digital return paths separated according to the datasheet reference layout, and confirm the required analog and digital supply rails before assigning the power tree, since the part is a mature catalog device whose full electrical detail must be read from the manufacturer datasheet.
推荐
Docking Stations and Speakerphone Cradles
Docking stations, speakerphone cradles and desktop audio accessories use the WM1800CGEFL/V to convert between the digital stream arriving from a host device and the analog line or speaker path of the accessory. The 32-pin QFN body leaves board area in a crowded dock enclosure for the power management and connectivity sections, and the single-package codec approach shortens the analog path between the connector and the amplifier, reducing susceptibility to EMI pickup. The legacy nature of this device makes it a natural fit for products that must extend the life of an existing platform rather than for a newly launched mass-market accessory. Confirm the supported audio interface, master clock requirements and any digital de-emphasis or filter configuration from the manufacturer datasheet, and validate the ripple seen by the codec when the same rail also feeds switching regulators in the dock.
推荐
Legacy Equipment Repair and Replacement
The WM1800CGEFL/V is used in repair and replacement builds of professional and consumer audio equipment originally designed around the Wolfson Microelectronics WM1800 codec. Because the /V code is supplied in a tested condition and the identical part is available in tube and tape-and-reel formats, a failed board can be restored without any redesign of the original layout. The 32-pin QFN land pattern is unchanged across the ordering codes, so the rework operation is a straightforward removal of the old device and reflow of the replacement. Before ordering, match the ordering code on the failed board against the package and revision marking so the replacement is the correct variant, and cross-check the pin assignment against the manufacturer datasheet during rework to confirm continuity on the analog and digital rails.
推荐
Digital-to-Analog Line Output Modules
In line-output modules for amplifiers, mixers and instrument equipment, the WM1800CGEFL/V provides a compact digital-to-analog path from a digital audio bus to a balanced or unbalanced analog line output. The 32-pin QFN footprint makes the codec practical where the converter must sit close to the output connector to keep the high-impedance analog leg short and shielded. The listed sigma-delta conversion architecture suits the resolution and dynamic range expected of studio-class line stages, while the compact body leaves routing space for the output protection and coupling network. Ground the exposed bottom land to the analog ground plane region and follow the datasheet reference layout for decoupling, and confirm the digital supply level and audio data format so the source controller can be configured correctly for the codec interface.
推荐
IoT Voice Front-Ends
Voice front-ends for IoT speaker nodes and smart-home audio devices can use the WM1800CGEFL/V to handle the analog microphone capture and the playback stream in a single package. Consolidating the converters into one 32-pin QFN device reduces the number of external components and PCB area, which is valuable in a sealed enclosure with limited ventilation and minimal passive volume. The digital interface characteristics and converter resolution must be read from the manufacturer datasheet for the specific ordering code to confirm the sampling rate and framing are supported by the host processor, since the published catalogue data identifies only a standard data interface. Plan the analog microphone biasing and the digital microphone path carefully, keep the codec supply on a filtered rail, and verify the operating temperature range against the enclosure conditions before committing to a production build.
推荐
推荐产品汇总
工程参考数据: WM1800CGEFL/V ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | WM1800CGEFL/RV | WM1800CGEFL | WM1800GEFL |
|---|---|---|---|---|
| Package | QFN-32, 5 x 5 x 0.9 mm | QFN-32, 5 x 5 x 0.9 mm - same | QFN-32, 5 x 5 x 0.9 mm - same | QFN-32, 5 x 5 x 0.9 mm - same |
| Brand | Cirrus Logic (Wolfson Microelectronics) | Cirrus Logic (Wolfson Microelectronics) | Cirrus Logic (Wolfson Microelectronics) | Cirrus Logic (Wolfson Microelectronics) |
| Device Category | Audio codec, Analog & Mixed Signal | Audio codec, Analog & Mixed Signal | Audio codec, Analog & Mixed Signal | Audio codec, Analog & Mixed Signal |
| Pin Count | 32 pins | 32 pins | 32 pins | 32 pins |
| Converter Architecture | Sigma-delta | Sigma-delta | Sigma-delta | Sigma-delta |
| Packing Format | Tube (/V suffix) | Tape and reel (/RV suffix) | Base catalog code, packing per manufacturer ordering table | Family code, packing per manufacturer ordering table |
| Condition | Tested | Tested / legacy distribution | Tested / legacy distribution | Catalog availability via distribution |
关键差异点
- Drop-in identical land pattern across all three ordering codes (对比 WM1800CGEFL/RV)
- Single-package analog capture and playback consolidation (对比 WM1800CGEFL)
- Legacy availability with a tested option for repair builds (对比 WM1800GEFL)
设计说明
The WM1800CGEFL/V is a leadless 32-pin QFN, so the layout must be taken directly from the datasheet land pattern rather than scaled from a generic footprint. Define a solder mask opening that matches the exposed bottom land, keep the land free of copper-defined solder mask dams that could trap solder, and route the exposed land to the analog ground reference used in the reference layout. Because the package is only 0.9 mm tall with no side leads, there is no visual confirmation of wicking during rework; verify each pin with a microscope after reflow.
The most common error on this device is ordering the wrong packing suffix and then discovering the mismatch at the assembly line: /V is tube-packed while /RV is tape-and-reel, and the base code has no suffix. State the required feeder format, the quantity and the acceptable condition on the purchase order so the delivered parts match the assembly plan. Also check the RoHS declaration, since catalogue listings for this legacy codec show both compliant and not-compliant markings, and request lot paperwork for certified builds.
Keep the analog microphone and line inputs away from the digital audio interface nets and from the switching nodes of any adjacent DC-DC converter. A common layout mistake on legacy audio designs is to route the codec supply from a noisy regulator without local filtering; add the datasheet-recommended bulk and high-frequency decoupling directly at the analog and digital supply pins, and give the codec an uninterrupted ground return path to the star point of the analog section.
Estimate the codec dissipation from the analog and digital currents given in the manufacturer datasheet multiplied by the corresponding supply rails, then check that the bottom land of the QFN has enough copper to keep the junction temperature within margin inside a sealed enclosure. In compact portable products the surrounding parts, rather than the codec, usually set the internal temperature, so measure the case temperature during thermal soak testing rather than assuming an ambient-based estimate. Reduce supply loss and heat by running the digital core at the lowest rail that meets the timing requirement.
合规信息
Supply-chain listings for this legacy codec show conflicting RoHS entries, one marking the Cirrus Logic line item compliant and another not compliant, so the overall RoHS status is recorded as unknown pending lot-specific documentation. The device is a mixed-signal audio IC and is not AEC-Q100 qualified.