AD526CDZ - Programmable Gain Amplifier | Analog Devices
MPN: AD526CDZ ✓ نشطAD526CDZ نظرة عامة
A software-programmable gain amplifier is a mixed-signal amplifier that uses digital control signals to select a predetermined gain. In the signal-chain hierarchy, the AD526 belongs to programmable-gain amplifiers, a specialized category of amplifier ICs used for instrumentation, industrial measurement, and data-acquisition systems. By changing gain through latched digital inputs rather than switching external resistors, it simplifies control and reduces the number of discrete components required around the amplifier.
The AD526CDZ provides five binary gain settings and uses TTL-compatible latched control inputs. Maximum gain error is 0.02% for the C grade at a gain of 1 and 0.5% at a gain of 16. Its 24 V/µs slew rate supports accurate reproduction of changing input waveforms. Two-chip cascade operation extends the binary gain range to 256, allowing a higher overall gain while retaining the digital gain-control architecture.
The AD526 integrates the amplifier and resistor network into one monolithic implementation. Because the gain network is internal, the circuit does not require external gain-setting resistors. The manufacturer identifies the C-grade part as offering a maximum gain error of 0.02% at a gain of 1, while the maximum error rises to 0.5% at a gain of 16. This increasing error with gain is important when interpreting the overall accuracy of a high-gain measurement chain.
Typical uses include programmable sensor-signal conditioning, laboratory instrumentation, industrial process measurement, and analog data-acquisition systems. The AD526 is particularly useful when a controller must adjust signal amplitude for inputs spanning several orders of magnitude. Its binary 1-to-16 gain range can be combined with an external attenuator or front-end stage when wider control is required.
Layout should preserve short analog input paths, a low-impedance reference or driver path, and clean digital control traces. Mount the device close to the source of the input signal to minimize parasitic capacitance and susceptibility to noise. Confirm the digital-control state before sampling the analog output, because the latched gain setting changes the transfer function and may create a transient during programming.
This page consolidates the AD526 family specifications, exact-package alternatives, programming considerations, and application guidance into an engineering-focused resource. It also distinguishes pin-compatible variants from functional or cross-package options, helping engineers evaluate replacements before changing a 16-CDIP circuit board.
بدائل مباشرة لـ AD526CDZ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع AD526CDZ (نفس عامل الشكل والبصمة) — يختلف في Package, Architecture, Amplifier Type, External Gain-Setting Components.
AD526CD
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←AD526ADZ
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←AD526BDZ
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←AD526JN
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←AD526CD-R2
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
AD526CDZ الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Programmable gain amplifier |
| Architecture | Single-ended monolithic SPGA |
| Number of Amplifiers | 1 circuit |
| Programmable Gain Settings | 1, 2, 4, 8, and 16 |
| Gain Error at Gain 1 | 0.02% maximum, C grade |
| Gain Error at Gain 16 | 0.5% maximum, C grade |
| Bandwidth | 4 MHz |
| Slew Rate | 24 V/µs |
| Supply Voltage Range | ±4.5 V to ±16.5 V |
| Control Input Compatibility | TTL-compatible latched inputs |
| Cascade Gain Range | Up to 256 with two chips |
| External Gain-Setting Components | None required |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| العلبة | 16-CDIP, 0.300 inch (7.62 mm) |
| نوع التركيب | Through-hole |
| Packaging | Tube |
دليل تكوين أطراف AD526CDZ 16-cdip, 0.300 inch (7.62 mm)
تكوين الأطراف لـ AD526CDZ (حزمة 16-cdip, 0.300 inch (7.62 mm)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ AD526CDZ.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
AD526CDZ مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Precision Data Acquisition, Laboratory Instrumentation, Programmable Gain Control Systems, Bridge and Transducer Measurement, Analog Signal Test and Measurement.
Industrial Sensor Signal Conditioning
The AD526CDZ fits industrial sensor-conditioning circuits whose signal level changes as process pressure, temperature, or position varies. Its digitally selected gains of 1, 2, 4, 8, and 16 let a controller adapt the analog level without changing external resistors. The 4 MHz bandwidth is substantially higher than many slow industrial measurement signals, while the 0.02% maximum gain error at gain 1 supports precise measurement at lower signal levels. Place the amplifier close to the sensor connector and provide stable reference and supply decoupling to prevent high-impedance sensor errors from being amplified along with the intended signal.
موصى به
Precision Data Acquisition
The AD526CDZ is useful in precision data-acquisition front ends where a controller must select gain before each analog-to-digital conversion. Programmable gains of 1 through 16 allow a consistent input range to be presented to an ADC, while the 24 V/µs slew rate supports waveforms beyond slow thermocouple or pressure-sensor bandwidths. The C-grade maximum gain errors of 0.02% at gain 1 and 0.5% at gain 16 must be included in the measurement budget. Latch the control word before the sampling instant and allow the output to settle, particularly when changing between widely separated gain settings.
موصى به
Laboratory Instrumentation
The AD526CDZ supports laboratory instruments that combine selectable gain with controlled signal conditioning. Its integrated amplifier and resistor network remove external gain-setting components, simplifying instrument front-end construction while retaining gains of 1, 2, 4, 8, and 16. The 4 MHz bandwidth is appropriate for general-purpose analog measurement and low-frequency waveform systems, whereas the 24 V/µs slew rate helps preserve large-signal behavior. For bench instruments, provide a clean ground reference, maintain short signal paths, and avoid routing the latched digital programming traces beneath sensitive analog inputs.
موصى به
Programmable Gain Control Systems
The AD526CDZ fits closed-loop or digitally supervised control systems that must reconfigure amplifier gain during operation. Latched TTL-compatible control inputs allow gain changes without mechanical resistor switching, reducing component count and enabling repeatable software-defined ranges. The device supports gains of 1, 2, 4, 8, and 16 and can be cascaded in a two-chip arrangement to reach a binary gain as high as 256. When cascading, account for the accuracy of both stages and ensure the second amplifier has adequate signal amplitude and bandwidth for the selected overall gain.
موصى به
Bridge and Transducer Measurement
The AD526CDZ can condition low-level bridge or transducer outputs when a fixed set of calibrated gain steps is preferable to manually selected resistors. Its monolithic gain network and digitally latched control simplify repeatable range changes in multi-range measurement equipment. The C-grade gain error is lowest at unity and increases toward 0.5% maximum at gain 16, so calibration and system-error calculations should reflect the operating range. Keep bridge excitation wiring and sensitive amplifier inputs away from digital control traces, and use a low-noise supply arrangement to avoid correlated noise appearing as measurement gain error.
موصى به
Analog Signal Test and Measurement
The AD526CDZ is suitable for analog test and measurement equipment requiring selectable amplification without external gain resistors. Gains of 1, 2, 4, 8, and 16 cover useful attenuation of large inputs and amplification of small ones, while the 4 MHz bandwidth provides headroom beyond many precision measurement systems. The 24 V/µs slew rate improves large-signal response when the selected gain multiplies the input amplitude. Validate the input range, output swing, and settling time at each programmed gain, and establish whether the 16-CDIP package's thermal performance is adequate for the required ambient temperature and enclosure conditions.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ AD526CDZ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | AD526CD | AD526ADZ | AD526BDZ | AD526JN | AD526CD-R2 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP, package and terminals reported as consistent | 16-CDIP, 0.300 inch (7.62 mm) | 16-CDIP, 0.300 inch (7.62 mm) | 16-CDIP, 0.300 inch (7.62 mm) | 16-CDIP, 0.300 inch (7.62 mm) |
| Amplifier Type | Single-ended programmable gain amplifier | Programmable/variable amplifier | Programmable gain amplifier | Programmable gain amplifier | Programmable gain amplifier | Programmable gain amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Programmable Gains | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 | 1, 2, 4, 8, and 16 |
| External Gain-Setting Components | None required | None required | None required | None required | None required | None required |
أبرز الفروقات
- C-grade gain accuracy in a programmable amplifier (مقابلAD526ADZ)
- Five binary gain selections without external gain resistors (مقابلAD526CD)
- Package-consistent AD526 family substitution path (مقابلAD526JN)
- High-speed gain control for general instrumentation (مقابلAD526BDZ)
ملاحظات التصميم
Place the AD526CDZ close to the analog source and route the input directly to the relevant amplifier pins. Keep the latched programming traces away from the input path and ground reference to reduce capacitive coupling and switching noise. Because the AD526 integrates its gain-setting resistor network, adding long external traces around the sensitive input nodes is unnecessary and can increase parasitic capacitance, susceptibility to interference, and settling time after a gain change.
Do not assume that every AD526 suffix has identical gain accuracy. The AD526CDZ is the C-grade device with maximum gain errors of 0.02% at gain 1 and 0.5% at gain 16, while A-, B-, and J-grade variants can have different limits or temperature coverage. Use the official AD526 datasheet to confirm the suffix, grade, supply range, pinout, and lifecycle status before treating a family member as a drop-in substitute.
Latch the gain-control word before starting a new measurement and allow sufficient settling time before sampling. A transition from gain 1 to gain 16 changes both the output amplitude and the feedback operating point, so the output can exhibit a transient. In repetitive acquisition systems, discard samples captured during the programming interval or use a calibrated settling sequence appropriate to the source impedance and acquisition bandwidth.
Operate the device from dual supplies within the specified ±4.5 V to ±16.5 V range and use a common, low-impedance ground reference for the analog and digital portions. Check output swing at the selected gain because a large input multiplied by gain 16 may approach the available output range. Decouple the supply pins close to the device and keep high-current return paths out of sensitive signal-ground paths.
معلومات الامتثال
The available product information identifies the AD526CDZ as a 16-CDIP programmable-gain amplifier, but it does not provide definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. Compliance status should be confirmed against the current Analog Devices product documentation before procurement.