Analog Devices

AD526CDZ - Programmable Gain Amplifier | Analog Devices

MPN: AD526CDZ ✓ Hoạt động
±4.5 V to ±16.5 V Vdss 16-CDIP, 0.300 inch (7.62 mm) Package
MOQ: 1 |

AD526CDZ Tóm tắt

The Analog Devices AD526CDZ is a single-ended, monolithic software-programmable gain amplifier (SPGA) with digitally selected gains of 1, 2, 4, 8, and 16, a 4 MHz bandwidth, and a 16-CDIP package. The device operates from dual ±4.5 V to ±16.5 V supplies and is specified over a -40°C to +85°C temperature range. Its integrated amplifier and resistor network eliminate the external gain-setting components normally required by a conventional PGA.

A software-programmable gain amplifier is a mixed-signal amplifier that uses digital control signals to select a predetermined gain. In the signal-chain hierarchy, the AD526 belongs to programmable-gain amplifiers, a specialized category of amplifier ICs used for instrumentation, industrial measurement, and data-acquisition systems. By changing gain through latched digital inputs rather than switching external resistors, it simplifies control and reduces the number of discrete components required around the amplifier.

The AD526CDZ provides five binary gain settings and uses TTL-compatible latched control inputs. Maximum gain error is 0.02% for the C grade at a gain of 1 and 0.5% at a gain of 16. Its 24 V/µs slew rate supports accurate reproduction of changing input waveforms. Two-chip cascade operation extends the binary gain range to 256, allowing a higher overall gain while retaining the digital gain-control architecture.

The AD526 integrates the amplifier and resistor network into one monolithic implementation. Because the gain network is internal, the circuit does not require external gain-setting resistors. The manufacturer identifies the C-grade part as offering a maximum gain error of 0.02% at a gain of 1, while the maximum error rises to 0.5% at a gain of 16. This increasing error with gain is important when interpreting the overall accuracy of a high-gain measurement chain.

Typical uses include programmable sensor-signal conditioning, laboratory instrumentation, industrial process measurement, and analog data-acquisition systems. The AD526 is particularly useful when a controller must adjust signal amplitude for inputs spanning several orders of magnitude. Its binary 1-to-16 gain range can be combined with an external attenuator or front-end stage when wider control is required.

Layout should preserve short analog input paths, a low-impedance reference or driver path, and clean digital control traces. Mount the device close to the source of the input signal to minimize parasitic capacitance and susceptibility to noise. Confirm the digital-control state before sampling the analog output, because the latched gain setting changes the transfer function and may create a transient during programming.

This page consolidates the AD526 family specifications, exact-package alternatives, programming considerations, and application guidance into an engineering-focused resource. It also distinguishes pin-compatible variants from functional or cross-package options, helping engineers evaluate replacements before changing a 16-CDIP circuit board.

Bộ thay thế dễ dàng lắp đặt cho AD526CDZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD526CDZ (cùng hình factor và footprint) — khác nhau ở Package, Architecture, Amplifier Type, External Gain-Setting Components.

Analog Devices
Package: 16-CDIP
Amplifier Type: Software-programmable gain amplifier
So sánh với AD526CDZ →
Analog Devices
Package: 16-CDIP, ceramic dual in-line package
Architecture: 1 amplifier circuit, single-ended
External Gain-Setting Components: 0 components required
So sánh với AD526CDZ →

AD526CD

✅ Drop-In
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Single-ended monolithic software-programmable gain amplifier (SPGA) · 1 amplifier circuit, single-ended · 1, 2, 4, 8, and 16 · 1 ratio · 16 ratio · TTL-compatible latched inputs · 0 components required · 1 amplifier and 1 resistor network

Liên hệ để biết giá

Xem tài liệu →

AD526ADZ

✅ Drop-In ⚠️ Thông số chưa được xác minh
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Single-ended monolithic software-programmable gain amplifier · 1 circuit · 1, 2, 4, 8, and 16 · 350 kHz · ±4.5 V to ±16 V · ±4.5 V · ±16 V · -55°C to +125°C

Liên hệ để biết giá

Xem tài liệu →

AD526BDZ

✅ Drop-In ⚠️ Thông số chưa được xác minh
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Software-programmable gain amplifier · 1 circuit · Single-ended monolithic SPGA · 1, 2, 4, 8, and 16 · 4 MHz · 24 V/µs · 50 pA · 250 µV

Liên hệ để biết giá

Xem tài liệu →

AD526JN

✅ Drop-In ⚠️ Thông số chưa được xác minh
Analog Devices
📦 16-CDIP (0.300 inch, 7.62 mm)
Single-ended monolithic software-programmable gain amplifier · 1, 2, 4, 8, and 16 · 5 · TTL-compatible latched inputs · Single-ended · 4.5 V to 16.5 V · 350 kHz · 0 °C to +70 °C

Liên hệ để biết giá

Xem tài liệu →

AD526CD-R2

✅ Drop-In
📦 16-CDIP (0.300 inch, 7.62 mm)
Same AD526CD electrical family with a 16-CDIP footprint; the -R2 ordering code must be checked for grade, temperature, and lifecycle differences before substitution.

📋 Tham chiếu thay thế (không có trong danh mục)

AD526CDZ Tỷ lệ tối đa & tính chất điện

Amplifier Type Programmable gain amplifier
Architecture Single-ended monolithic SPGA
Number of Amplifiers 1 circuit
Programmable Gain Settings 1, 2, 4, 8, and 16
Gain Error at Gain 1 0.02% maximum, C grade
Gain Error at Gain 16 0.5% maximum, C grade
Bandwidth 4 MHz
Slew Rate 24 V/µs
Supply Voltage Range ±4.5 V to ±16.5 V
Control Input Compatibility TTL-compatible latched inputs
Cascade Gain Range Up to 256 with two chips
External Gain-Setting Components None required
Khoảng nhiệt độ hoạt động -40°C to +85°C
Hộp 16-CDIP, 0.300 inch (7.62 mm)
Kiểu lắp đặt Through-hole
Packaging Tube

Hướng dẫn cấu hình chân AD526CDZ 16-cdip, 0.300 inch (7.62 mm)

Cấu hình chân cho AD526CDZ (16-cdip, 0.300 inch (7.62 mm) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 16-cdip, 0.300 inch (7.62 mm) cho AD526CDZ

Không có dữ liệu chân cụ thể sẵn có cho AD526CDZ.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

AD526CDZ phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Precision Data Acquisition, Laboratory Instrumentation, Programmable Gain Control Systems, Bridge and Transducer Measurement, Analog Signal Test and Measurement.

🏭

Industrial Sensor Signal Conditioning

The AD526CDZ fits industrial sensor-conditioning circuits whose signal level changes as process pressure, temperature, or position varies. Its digitally selected gains of 1, 2, 4, 8, and 16 let a controller adapt the analog level without changing external resistors. The 4 MHz bandwidth is substantially higher than many slow industrial measurement signals, while the 0.02% maximum gain error at gain 1 supports precise measurement at lower signal levels. Place the amplifier close to the sensor connector and provide stable reference and supply decoupling to prevent high-impedance sensor errors from being amplified along with the intended signal.

📊

Precision Data Acquisition

The AD526CDZ is useful in precision data-acquisition front ends where a controller must select gain before each analog-to-digital conversion. Programmable gains of 1 through 16 allow a consistent input range to be presented to an ADC, while the 24 V/µs slew rate supports waveforms beyond slow thermocouple or pressure-sensor bandwidths. The C-grade maximum gain errors of 0.02% at gain 1 and 0.5% at gain 16 must be included in the measurement budget. Latch the control word before the sampling instant and allow the output to settle, particularly when changing between widely separated gain settings.

🔧

Laboratory Instrumentation

The AD526CDZ supports laboratory instruments that combine selectable gain with controlled signal conditioning. Its integrated amplifier and resistor network remove external gain-setting components, simplifying instrument front-end construction while retaining gains of 1, 2, 4, 8, and 16. The 4 MHz bandwidth is appropriate for general-purpose analog measurement and low-frequency waveform systems, whereas the 24 V/µs slew rate helps preserve large-signal behavior. For bench instruments, provide a clean ground reference, maintain short signal paths, and avoid routing the latched digital programming traces beneath sensitive analog inputs.

🖥️

Programmable Gain Control Systems

The AD526CDZ fits closed-loop or digitally supervised control systems that must reconfigure amplifier gain during operation. Latched TTL-compatible control inputs allow gain changes without mechanical resistor switching, reducing component count and enabling repeatable software-defined ranges. The device supports gains of 1, 2, 4, 8, and 16 and can be cascaded in a two-chip arrangement to reach a binary gain as high as 256. When cascading, account for the accuracy of both stages and ensure the second amplifier has adequate signal amplitude and bandwidth for the selected overall gain.

📈

Bridge and Transducer Measurement

The AD526CDZ can condition low-level bridge or transducer outputs when a fixed set of calibrated gain steps is preferable to manually selected resistors. Its monolithic gain network and digitally latched control simplify repeatable range changes in multi-range measurement equipment. The C-grade gain error is lowest at unity and increases toward 0.5% maximum at gain 16, so calibration and system-error calculations should reflect the operating range. Keep bridge excitation wiring and sensitive amplifier inputs away from digital control traces, and use a low-noise supply arrangement to avoid correlated noise appearing as measurement gain error.

🧪

Analog Signal Test and Measurement

The AD526CDZ is suitable for analog test and measurement equipment requiring selectable amplification without external gain resistors. Gains of 1, 2, 4, 8, and 16 cover useful attenuation of large inputs and amplification of small ones, while the 4 MHz bandwidth provides headroom beyond many precision measurement systems. The 24 V/µs slew rate improves large-signal response when the selected gain multiplies the input amplitude. Validate the input range, output swing, and settling time at each programmed gain, and establish whether the 16-CDIP package's thermal performance is adequate for the required ambient temperature and enclosure conditions.

Tóm tắt các sản phẩm được đề xuất

AD526CD Analog Devices Được sử dụng trong: Industrial Sensor Signal Conditioning, Precision Data Acquisition, Laboratory Instrumentation, Bridge and Transducer Measurement, Analog Signal Test and Measurement AD526JN AD526 family device for industrial signal-path evaluation Được sử dụng trong: Industrial Sensor Signal Conditioning, Bridge and Transducer Measurement AD526BDZ Analog Devices Được sử dụng trong: Precision Data Acquisition, Programmable Gain Control Systems AD526CD-R2 Additional AD526CD ordering option Được sử dụng trong: Laboratory Instrumentation, Analog Signal Test and Measurement AD526ADZ Analog Devices Được sử dụng trong: Programmable Gain Control Systems
What is the AD526CDZ and what are its key specifications?
The AD526CDZ is a single-ended monolithic software-programmable gain amplifier with gains of 1, 2, 4, 8, and 16, a 4 MHz bandwidth, and a 24 V/µs slew rate. According to the Analog Devices AD526 datasheet, it uses TTL-compatible latched inputs, requires no external gain-setting components, and operates from ±4.5 V to ±16.5 V. The C-grade device specifies a maximum gain error of 0.02% at gain 1 and 0.5% at gain 16. It is packaged in a 16-CDIP package for through-hole PCB assembly.
Where can I download the AD526CDZ datasheet PDF?
The official AD526CDZ datasheet PDF is available from Analog Devices at https://www.analog.com/media/en/technical-documentation/data-sheets/AD526.pdf. The manufacturer datasheet describes the programmable gains of 1, 2, 4, 8, and 16, TTL-compatible latched control inputs, dual-supply operation, electrical characteristics, and package information. Use the Analog Devices product page at https://www.analog.com/en/products/AD526.html for the family overview and additional product resources.
Where can I find the AD526CDZ pinout?
The AD526CDZ pin assignment is shown in the pin-configuration section of the official Analog Devices AD526 datasheet. The component is a 16-lead CDIP device, and its exposed thermal and electrical characteristics must be assessed together with the complete pin table. Before assigning PCB tracks or connecting control signals, use the datasheet's pin-description drawing and verify the package orientation against the physical notch or pin-1 marking.
How do I program the gain of an AD526CDZ?
The AD526CDZ is programmed through TTL-compatible latched digital inputs that select gains of 1, 2, 4, 8, or 16. According to the Analog Devices AD526 datasheet, the control signals are latched so their state determines the amplifier's gain configuration. Follow the truth table in the manufacturer datasheet when mapping the input pins, allow the circuit to settle after changing the gain, and start the subsequent conversion only after the analog output has stabilized.
What is the operating voltage range of the AD526CDZ?
The AD526CDZ operates from dual supplies of ±4.5 V to ±16.5 V. This means the total span between the negative and positive supply rails is 9 V to 33 V. The Analog Devices AD526 datasheet identifies the minimum ±4.5 V supply condition and the maximum ±16.5 V condition. Both supply rails and the ground reference must remain within their specified limits during power-up, shutdown, and normal signal acquisition.
How accurate is the AD526CDZ gain at 1 and 16?
For the C-grade AD526CDZ, the maximum gain error is 0.02% at a gain of 1 and 0.5% at a gain of 16. These limits come from the Analog Devices AD526 datasheet. The increase in error at the highest gain reflects the cumulative tolerance and distortion behavior of a larger internal gain multiplication, so system error budgets should be calculated at the gain actually used rather than using the gain-1 limit for every range.
What is the bandwidth and slew rate of the AD526CDZ?
The AD526CDZ has a 4 MHz bandwidth and a 24 V/µs slew rate. The Analog Devices AD526 datasheet lists the 4 MHz figure as its small-signal bandwidth characteristic and 24 V/µs as the slew-rate characteristic. These values indicate that it can process substantially faster signals than many instrumentation-amplifier stages, but system bandwidth should also account for the selected gain, source impedance, filtering, and ADC acquisition time.
AD526CDZ vs AD526CD - which is the correct replacement?
The AD526CD and AD526CDZ are presented as having consistent performance, terminals, and packages, making the AD526CD a candidate for replacing the AD526CDZ without PCB modification. The comparison source specifically identifies the AD526CD as a package-consistent replacement for AD526CDZ. Confirm the exact suffix, temperature grade, supply rating, and pin orientation against the manufacturer datasheet before approving the substitution for production.
When should I choose the AD526CDZ instead of an AD526 grade variant?
Choose the AD526CDZ when the design requires the C-grade gain-error limits of 0.02% at gain 1 and 0.5% at gain 16 and must retain the 16-CDIP footprint. Lower AD526 grades may be appropriate when their specified gain accuracy is sufficient and the design has additional calibration. Because the AD526 family includes multiple suffixes, verify gain error, temperature range, package, and legacy product status before finalizing a board revision.
What is the best drop-in replacement for AD526CDZ?
The AD526CD is the clearest documented package-consistent replacement for the AD526CDZ because the available comparison identifies matching terminals, package, and functional characteristics. Other AD526 family devices may differ in accuracy grade, temperature range, package construction, or lifecycle status, so they should not be treated as automatic replacements. For a production substitution, compare the manufacturer pin table, electrical limits, gain error, and qualification requirements.
Can AD526JN replace AD526CDZ in an existing circuit?
The AD526JN is a same-family candidate for an AD526CDZ replacement only if its exact package, pinout, electrical ratings, and gain-error grade meet the original circuit requirements. The available comparison identifies differences involving RoHS, REACH, package type, and other characteristics rather than guaranteeing equivalence. Treat the AD526JN as a design-review candidate and verify it against the official AD526 datasheet before committing a new production order.
Where can I buy AD526CDZ and check its price and stock?
Use the Request a Quote form on this page to request AD526CDZ pricing, current availability, and lead time from XAIPART. The part is also listed by authorized supply channels, but stock and commercial terms can change without notice. Provide the required quantity, package form, and target delivery date with the request so the quotation can be matched to the 16-CDIP AD526CDZ configuration.
What is the lead time for AD526CDZ?
The current lead time for AD526CDZ should be confirmed through the Request a Quote form on this page because it can vary with quantity, package form, inventory position, and manufacturing status. Do not base a production schedule on a generic catalog interval. Include your annual usage, forecast, and required delivery dates in the request to obtain a commitment suitable for the actual procurement plan.
Is AD526CDZ currently in stock?
Current AD526CDZ stock should be checked through the Request a Quote form on this page. Distributor listings and manufacturer product resources confirm that the device is a cataloged 16-CDIP programmable-gain amplifier, but a listing alone is not a live inventory guarantee. Include the required quantity and delivery location in the request, and specify whether unopened tube packing or another approved delivery format is required.
Is the AD526CDZ suitable for sensor instrumentation and data acquisition?
The AD526CDZ is suitable for sensor instrumentation and data-acquisition systems that need digitally selected gains of 1, 2, 4, 8, or 16. Its 4 MHz bandwidth, 24 V/µs slew rate, and integrated resistor network simplify analog front-end design. According to the Analog Devices datasheet, no external gain-setting components are required. The selected gain error and input bandwidth must still be included in the end-to-end measurement uncertainty.
What is the best Analog Devices equivalent for the AD526CDZ?
The AD526CD is the strongest documented Analog Devices equivalent because the available comparison identifies matching package, terminals, and principal functional characteristics. It should be the first candidate evaluated for a direct AD526CDZ substitution. Alternatives such as AD526ADZ, AD526BDZ, and AD526JN belong to the same family but may differ in gain accuracy, temperature coverage, or lifecycle status, so each must be checked against the original electrical requirements.

Dữ liệu tham khảo kỹ thuật cho AD526CDZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose the AD526CDZ when the design needs a 16-CDIP programmable-gain amplifier with binary gains of 1, 2, 4, 8, and 16 and requires the C-grade limits of 0.02% gain error at gain 1 and 0.5% at gain 16. Choose the AD526CD when a documented package- and terminal-consistent replacement is needed and its ordering suffix satisfies the production requirements. Consider the AD526BDZ when its intermediate grade accuracy is sufficient, and use the AD526ADZ only when the looser gain-error limits meet the measurement budget. The AD526JN should be selected only after checking its temperature, accuracy, and lifecycle characteristics against the original circuit. For any substitution, confirm the manufacturer pin table, dual-supply limits, output swing, external-component requirements, and qualification needs before production release.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này AD526CD AD526ADZ AD526BDZ AD526JN AD526CD-R2
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-CDIP (0.300 inch, 7.62 mm) 16-CDIP, package and terminals reported as consistent 16-CDIP, 0.300 inch (7.62 mm) 16-CDIP, 0.300 inch (7.62 mm) 16-CDIP, 0.300 inch (7.62 mm) 16-CDIP, 0.300 inch (7.62 mm)
Amplifier Type Single-ended programmable gain amplifier Programmable/variable amplifier Programmable gain amplifier Programmable gain amplifier Programmable gain amplifier Programmable gain amplifier
Number of Circuits 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit 1 circuit
Programmable Gains 1, 2, 4, 8, and 16 1, 2, 4, 8, and 16 1, 2, 4, 8, and 16 1, 2, 4, 8, and 16 1, 2, 4, 8, and 16 1, 2, 4, 8, and 16
External Gain-Setting Components None required None required None required None required None required None required

Bảo phân biệt quan trọng

  • C-grade gain accuracy in a programmable amplifier (vsAD526ADZ)
  • Five binary gain selections without external gain resistors (vsAD526CD)
  • Package-consistent AD526 family substitution path (vsAD526JN)
  • High-speed gain control for general instrumentation (vsAD526BDZ)

Ghi chú thiết kế

Place the AD526CDZ close to the analog source and route the input directly to the relevant amplifier pins. Keep the latched programming traces away from the input path and ground reference to reduce capacitive coupling and switching noise. Because the AD526 integrates its gain-setting resistor network, adding long external traces around the sensitive input nodes is unnecessary and can increase parasitic capacitance, susceptibility to interference, and settling time after a gain change.

Do not assume that every AD526 suffix has identical gain accuracy. The AD526CDZ is the C-grade device with maximum gain errors of 0.02% at gain 1 and 0.5% at gain 16, while A-, B-, and J-grade variants can have different limits or temperature coverage. Use the official AD526 datasheet to confirm the suffix, grade, supply range, pinout, and lifecycle status before treating a family member as a drop-in substitute.

Latch the gain-control word before starting a new measurement and allow sufficient settling time before sampling. A transition from gain 1 to gain 16 changes both the output amplitude and the feedback operating point, so the output can exhibit a transient. In repetitive acquisition systems, discard samples captured during the programming interval or use a calibrated settling sequence appropriate to the source impedance and acquisition bandwidth.

Operate the device from dual supplies within the specified ±4.5 V to ±16.5 V range and use a common, low-impedance ground reference for the analog and digital portions. Check output swing at the selected gain because a large input multiplied by gain 16 may approach the available output range. Decouple the supply pins close to the device and keep high-current return paths out of sensitive signal-ground paths.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The available product information identifies the AD526CDZ as a 16-CDIP programmable-gain amplifier, but it does not provide definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. Compliance status should be confirmed against the current Analog Devices product documentation before procurement.

Dữ liệu được xác minh vào: 2026-11-18 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

AD526CDZ datasheet AD526CDZ pinout AD526CDZ datasheet pdf AD526CDZ specifications AD526CDZ programmable gain amplifier AD526CDZ 16-CDIP AD526CDZ gain settings AD526CDZ drop-in replacement AD526CDZ vs AD526CD Analog Devices AD526CDZ AD526CDZ sensor signal conditioning AD526CDZ price

Các bộ phận và thuật ngữ liên quan

Analog Devices AD526 AD526CDZ AD526CD AD526ADZ AD526BDZ AD526JN AD526CD-R2 software-programmable gain amplifier SPGA programmable gain amplifier mixed-signal amplifier amplifier IC instrumentation amplifier application TTL-compatible latched input gain error slew rate bandwidth 16-CDIP ceramic dual in-line package through-hole package industrial sensor conditioning data acquisition analog signal measurement RoHS REACH
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ