Analog Devices

AD626BN - True Single-Supply Differential Amplifier | ADI

MPN: AD626BN ✓ نشط
+2.4 V to +10 V Vdss 8-pin PDIP Package
الحد الأدنى للطلب: 1 |

AD626BN نظرة عامة

The Analog Devices AD626BN is a true single-supply differential amplifier designed to amplify small differential signals that coexist with large common-mode voltages. It operates from a single +2.4 V to +10 V supply or from dual ±1.2 V to ±6 V supplies, has a 100 kHz bandwidth, and is offered in an 8-pin PDIP package. Its maximum input offset voltage is 2.5 mV.

A differential amplifier is an amplifier that responds to the voltage difference between two inputs while rejecting voltage common to both inputs. Within the amplifier-IC hierarchy, the AD626BN is a difference amplifier rather than a general-purpose operational amplifier. It is particularly useful when a small sensor or measurement signal must be extracted in the presence of a larger common-mode voltage, reducing the risk that the common-mode component will saturate the signal chain.

The principal advantages are its low-cost single-supply operation, true differential input stage, and ability to operate from supplies as low as +2.4 V. The single +2.4 V to +10 V range supports low-voltage sensor systems, while the dual-supply option extends operation to ±1.2 V to ±6 V. The 100 kHz bandwidth is suitable for low-frequency differential measurements rather than high-speed signal processing.

In a typical circuit, the two input pins receive the sensor signal and its reference or return path. The amplifier produces an output proportional to the difference between those inputs while the internal architecture suppresses much of the common-mode voltage. Gain is established with external feedback resistors, allowing the circuit to be adapted to different input ranges. Supply decoupling and correct resistor placement remain important because input and output noise directly affect the fidelity of the amplified measurement.

Typical uses include current-sense and bridge-signal conditioning, instrumentation interfaces, industrial measurement systems, and low-frequency sensor acquisition. The 8-pin PDIP package is also useful for prototypes, educational circuits, and through-hole industrial control boards where a surface-mount footprint would be inconvenient. Dual-supply operation can simplify systems that already provide symmetrical rails and require bipolar input or output signaling.

For a new design, verify the input common-mode range at every supply voltage and confirm that output swing remains within the selected supply limits. Check the feedback-resistor values against the required gain, place the bypass capacitor close to the supply pins, and avoid driving capacitive loads unless the resulting stability behavior has been checked. Those precautions are more important than raw bandwidth when extracting a reliable low-level differential measurement.

This page combines the manufacturer's functional description with practical design guidance, package and supply details, a structured comparison, and a focused view of compatible replacement options. It is intended to help engineers answer specification, application, sourcing, and replacement questions without relying on basic distributor listings alone.

بدائل مباشرة لـ AD626BN — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع AD626BN (نفس عامل الشكل والبصمة) — يختلف في Input Common-Mode Range, Operating Temperature Range, Product Type, Single-Supply Operating Voltage.

Analog Devices
Input Common-Mode Range: Approximately 6 × (+VS − 1 V)
Operating Temperature Range: -40 °C to 85 °C
Product Type: Single-supply differential amplifier
قارن مع AD626BN →

AD626ANZ

✅ بديل مباشر
Analog Devices
📦 8-pin PDIP
Single-supply differential amplifier · 1 circuit · 2.4 V to 10 V · ±1.2 V to ±6 V · 2.5 mV · 100 dB · 100 kHz · Approximately 6 × (+VS − 1 V)

تواصل لمعرفة السعر

عرض ورقة البيانات ←

AD626BNZ

✅ بديل مباشر
📦 8-pin PDIP
Same 8-pin PDIP configuration with 2.5 mV maximum offset, 100 kHz bandwidth, and -40 °C to +85 °C operation; only the ordering-code details differ.

📋 بديل مرجعي (غير موجود في الكتالوج)

AD626ARZ

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin PDIP
Same AD626 differential-amplifier family and 8-pin PDIP footprint; electrical and ordering-code differences are not numerically characterized in the available records, so the match is treated conservatively.

📋 بديل مرجعي (غير موجود في الكتالوج)

AD626AR

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-pin PDIP
Same AD626 differential-amplifier family and 8-pin PDIP footprint; suffix-specific electrical tolerances and packing details require comparison with the AD626BN ordering table.

📋 بديل مرجعي (غير موجود في الكتالوج)

AD626BN الحدود القصوى والخصائص الكهربائية

Product Type True single-supply differential amplifier
Number of Amplifiers 1 circuit
Single-Supply Operating Voltage +2.4 V to +10 V
Dual-Supply Operating Voltage ±1.2 V to ±6 V
Bandwidth 100 kHz
Maximum Input Offset Voltage 2.5 mV
Input Common-Mode Range Equal to 6 × (VS − 1 V)
العلبة 8-pin PDIP
عدد الأطراف 8 pins
نوع التركيب Through-hole
Supplier Configuration Tube
نطاق درجة حرارة التشغيل -40 °C to +85 °C

دليل تكوين أطراف AD626BN 8-pin pdip

تكوين الأطراف لـ AD626BN (حزمة 8-pin pdip). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 8-pin pdip لـ AD626BN

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ AD626BN.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

AD626BN مناسب لـ 6 التطبيقs: Bridge Sensor Signal Conditioning, Current-Sense Amplification, Instrumentation Signal Interfaces, Industrial Process Monitoring, Battery-Powered Sensor Nodes, Low-Frequency Low-Pass Filtering.

🏭

Bridge Sensor Signal Conditioning

The AD626BN is well suited to low-frequency bridge measurements because its true differential input extracts the small voltage generated by a resistive bridge while attenuating a much larger common-mode voltage. With a 100 kHz bandwidth, it can condition pressure, load-cell, and strain-gauge signals that fall well below that frequency. The circuit is normally connected between the bridge excitation and a low-pass filter. Designers should verify that the bridge voltage and output swing remain within the amplifier's input common-mode range and output limits for the selected +2.4 V to +10 V or ±1.2 V to ±6 V supply.

⚡

Current-Sense Amplification

The AD626BN can amplify the small differential voltage developed across a current-sense resistor while rejecting the larger voltage shared by both resistor terminals. Its single-supply capability is useful in compact battery-powered or industrial systems, while the 2.5 mV maximum input offset may be significant when the shunt voltage is very small. Gain is established with external feedback components. Confirm that the common-mode input voltage remains valid as the shunt current changes, and assess offset and noise against the smallest current level that must be measured.

🧩

Instrumentation Signal Interfaces

AD626BN provides a cost-conscious differential input stage for low-level instrumentation signals where the source includes substantial common-mode voltage. It can form the analog front end of a measurement system before a separate low-pass filter and converter. The 100 kHz bandwidth supports slow sensor signals rather than high-speed data acquisition, so applications requiring wider bandwidth should choose a different amplifier. Feedback resistors set the differential gain, and their tolerance contributes directly to gain error. Layout should keep the differential input path compact and symmetrical.

🏭

Industrial Process Monitoring

The AD626BN can condition low-level differential process signals generated by pressure, temperature, or flow transmitters when the transmitter output includes a common-mode voltage. Its dual-supply range of ±1.2 V to ±6 V permits operation in symmetrical industrial control systems, while the single-supply range supports lower-voltage panels. The amplifier is appropriate for slow-changing process variables because its bandwidth is 100 kHz. Design validation should include startup behavior, output settling, electrical noise, and the common-mode headroom present during fault or sensor-disconnection conditions.

📱

Battery-Powered Sensor Nodes

A +2.4 V to +10 V supply range makes the AD626BN usable in compact low-voltage sensor nodes that cannot support dual rails. It can amplify a differential sensor output before an ADC or comparator, reducing the need for separate subtraction circuitry. The trade-off is that single-supply operation constrains output headroom and common-mode range, especially near the lower supply limit. Use the lowest practical gain that preserves signal integrity, and verify startup, quiescent-current, and battery-voltage behavior across the complete operating range.

🔧

Low-Frequency Low-Pass Filtering

AD626BN is designed to amplify and low-pass filter small differential voltages, making it useful as the gain stage preceding an active filter in a sensor signal chain. Its 100 kHz bandwidth accommodates signals well below that limit, while external feedback components determine the closed-loop response and gain. Place the amplifier close to the filtering network to minimize high-frequency pickup and ground-current coupling. Decouple the supply pin locally, maintain symmetric differential routing where practical, and validate filter stability and settling using the actual source impedance and load capacitance.

What is the AD626BN and what is its main function?
The AD626BN is a true single-supply differential amplifier intended to amplify small differential voltages while rejecting large common-mode voltages. According to the Analog Devices product page and manufacturer datasheet, it operates from one +2.4 V to +10 V supply or from dual ±1.2 V to ±6 V supplies and is packaged in an 8-pin PDIP. Its differential architecture is useful for bridge sensors, instrumentation signals, and other measurements where a common signal could otherwise overwhelm the wanted signal.
What is the operating voltage range of AD626BN?
The AD626BN operates from +2.4 V to +10 V in a single-supply configuration or from ±1.2 V to ±6 V in a dual-supply configuration. The Analog Devices product page explicitly identifies both ranges. Single-supply operation is useful in low-voltage sensor systems because the amplifier can work with one positive rail, while dual-supply operation supports bipolar signal chains and designs that already contain symmetrical supply rails.
Where can I download the AD626BN datasheet PDF?
The official AD626BN technical documentation is available through the Analog Devices AD626 product page at https://www.analog.com/en/products/ad626.html, where the manufacturer provides the datasheet and product information. The AD626BN uses the same AD626 family documentation as the AD626BNZ package ordering code. Use the pin-description and electrical-characteristics tables in that document when assigning the 8-pin PDIP connections and checking operating limits.
Where can I find the AD626BN pinout?
The AD626BN pin assignment is shown in the pin-configuration table of the Analog Devices AD626 manufacturer datasheet, accessible from the official AD626 product page. The component is an 8-pin PDIP device, so the physical pin numbering follows the standard counter-clockwise numbering of a DIP with the pin-1 end identified by the package notch. Confirm each signal against the datasheet before assigning PCB tracks or designing a replacement board.
What are the key specifications of AD626BN that engineers should know?
The AD626BN is a one-amplifier differential IC with a 100 kHz bandwidth, 2.5 mV maximum input offset voltage, and an 8-pin PDIP package. According to the Analog Devices product page, its operating range is +2.4 V to +10 V from one supply or ±1.2 V to ±6 V from two supplies. These figures position it as a low-frequency, low-cost difference amplifier rather than a high-speed, precision instrumentation-amplifier family.
AD626BN vs AD626ANZ - which is the better choice?
AD626BN and AD626ANZ are closely related AD626-family orderable variants, and the AD626ANZ comparison record identifies them as alternatives with the same differential-amplifier function. AD626BN is identified as an 8-pin PDIP part, while the exact ordering-code and temperature differences should be checked in the manufacturer ordering table before substitution. For an existing AD626BN footprint, retain the original suffix unless the latest datasheet confirms the replacement's grade, packing code, and environmental requirements.
When should I choose AD626BN over another differential amplifier?
Choose AD626BN when the design needs a low-cost differential amplifier that can operate directly from a single +2.4 V to +10 V rail and only needs a 100 kHz bandwidth. It is appropriate for low-frequency bridge, current-sense, and instrumentation signals where the common-mode voltage is much larger than the differential signal. A precision instrumentation amplifier may be preferable when very low offset, high CMRR, unusual gains, or broader input-range capability is essential.
Is AD626BN suitable for sensor and bridge measurement applications?
The AD626BN is suitable for many low-frequency differential sensor and bridge measurements because its true differential input rejects common-mode voltage while preserving small signal differences. Its 100 kHz bandwidth is adequate for many temperature, pressure, and strain-based systems operating well below that frequency. The circuit must still remain within the input common-mode range at the actual supply voltage, and resistor tolerance and amplifier offset will influence overall measurement accuracy.
What can replace AD626BN on the same 8-pin PDIP footprint?
AD626ANZ and AD626BNZ are the closest documented orderable alternatives for an AD626BN replacement, both associated with the same AD626 family and 8-pin PDIP configuration. A replacement should still be checked for exact offset, temperature grade, packing code, and supply requirements before use. No unqualified cross-manufacturer drop-in part is recommended without a manufacturer pinout and electrical comparison confirming compatibility.
Is AD626BN the same as AD626BNZ?
AD626BN and AD626BNZ are orderable variants of the Analog Devices AD626 differential amplifier and are closely related, but the suffix can identify different manufacturing or packaging details. The verified product records identify both as 8-pin PDIP differential amplifiers, and the AD626BNZ listing states 2.5 mV offset, 100 kHz bandwidth, and -40 °C to +85 °C. Check the manufacturer's ordering guide for the exact distinction before treating the codes as identical.
Where can I buy AD626BN online and what is its price?
The AD626BN can be requested through the Request a Quote form on this page, where the exact suffix, quantity, and current commercial terms can be confirmed. Pricing is not reproduced in the published technical content because it can change independently of the device's electrical characteristics. The form is also the appropriate route for checking current availability, minimum order quantity, and lead time for the 8-pin PDIP device.
What is the lead time for AD626BN?
The current AD626BN lead time depends on manufacturer inventory, package variant, order quantity, and replenishment status. Use the Request a Quote form on this page to obtain the latest lead-time statement for the exact AD626BN ordering code. Engineers should include their required delivery date and annual usage so that scheduling information can reflect the actual production requirement rather than a generic quantity-one estimate.
Is AD626BN currently in stock?
Stock for the exact AD626BN suffix should be confirmed through the Request a Quote form on this page because availability can vary by package code and order quantity. The manufacturer product page confirms that the AD626 family is documented, but it does not establish a quantity-specific stock allocation for a particular order. Submit the required part number, quantity, and target date to receive the current supply position.
How much power does AD626BN dissipate and does it need a heatsink?
The AD626BN is an 8-pin PDIP low-power analog amplifier, and its normal thermal requirement is normally modest because it does not use the package as a high-power device. The exact dissipation depends on supply voltage, quiescent current, output loading, and ambient temperature. Since the complete supply-current and thermal-resistance figures are not stated in the manufacturer product summary, calculate junction temperature from the applicable datasheet values before setting a maximum output-load condition.
What is the best Analog Devices equivalent for AD626BN?
The closest documented Analog Devices equivalents are AD626ANZ and AD626BNZ because the comparison records explicitly associate them with AD626BN and the same 8-pin PDIP device family. The AD626BNZ record gives 2.5 mV maximum offset, 100 kHz bandwidth, and a -40 °C to +85 °C range. Confirm the current ordering information, pinout, grade, and packing suffix on the manufacturer documentation before committing to either alternative.

بيانات مرجعية هندسية لـ AD626BN — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose AD626BN for a low-cost, low-frequency differential signal chain that can use a single +2.4 V to +10 V rail or dual ±1.2 V to ±6 V rails and operates in an 8-pin PDIP footprint. It is particularly appropriate for bridge sensors, shunt monitoring, and process signals where a large common-mode voltage surrounds a small differential signal. AD626ANZ and AD626BNZ are the closest documented family alternatives when the exact AD626BN ordering code is difficult to obtain; verify suffix-specific grade and packing details before substitution. AD626ARZ and AD626AR retain the same family and package concept but have less complete comparative electrical information, so use them only after checking the current manufacturer datasheet and pin table. For high-speed signals, very low offset, unusually broad common-mode range, or precision gain settings, select a device with dedicated ratings for those requirements rather than assuming pin compatibility alone guarantees equivalent performance.

المقارنة مع البدائل

المعامل هذا المنتج AD626ANZ AD626BNZ AD626ARZ AD626AR
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Package 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP 8-pin PDIP
Product Type True single-supply differential amplifier Differential amplifier Differential amplifier Differential amplifier Differential amplifier
Number of Amplifiers 1 circuit 1 circuit 1 amplifier 1 circuit 1 circuit

أبرز الفروقات

  • Supports true single-supply operation down to +2.4 V (مقابلAD626BNZ)
  • Matches the documented 8-pin PDIP AD626 family footprint (مقابلAD626ANZ)
  • Combines differential signal extraction with a 100 kHz bandwidth (مقابلAD626BNZ)

ملاحظات التصميم

Choose the supply configuration around both the source signal and the required output swing. Single-supply operation from +2.4 V to +10 V reduces system complexity, but it restricts output and input headroom near the lower rail. Dual supplies from ±1.2 V to ±6 V simplify bipolar signal chains. Confirm the actual common-mode voltage against 6 × (VS − 1 V), and ensure the output remains inside the amplifier's permitted swing under both normal load and worst-case input conditions.

Route the two differential inputs as closely together as practical, keeping the feedback resistors close to the amplifier pins. Place the supply bypass capacitor next to the corresponding power pin and provide a direct ground return to prevent output-current transients from modulating the input reference. For bridge or shunt measurements, avoid long parallel copper paths where injected current could create differential error. The 100 kHz bandwidth does not remove the need for disciplined high-frequency layout.

Do not assume that any AD626 suffix is automatically interchangeable. Confirm the 8-pin PDIP pinout, temperature grade, offset limit, bandwidth, supply range, and packing code in the manufacturer ordering table before replacing AD626BN. The 2.5 mV maximum input offset can dominate a measurement with a small differential signal, so calculate its effect at the minimum input level and include resistor tolerance and sensor sensitivity in the error budget.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The AD626 manufacturer product page and family documentation describe the electrical function and operating ranges but do not state the requested compliance attributes.

تم التحقق من البيانات في: 2026-11-18 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

AD626BN datasheet AD626BN pinout AD626BN datasheet pdf AD626BN specifications AD626BN equivalent AD626BN replacement AD626BN vs AD626ANZ AD626BN vs AD626BNZ AD626BN single supply amplifier AD626BN 8-pin PDIP AD626BN current sense amplifier AD626BN bridge sensor AD626BN price AD626BN stock Analog Devices AD626BN

المكونات والمصطلحات ذات الصلة

Analog Devices AD626 AD626BN AD626ANZ AD626BNZ AD626ARZ AD626AR differential amplifier true single-supply differential amplifier amplifier IC difference amplifier input offset voltage common-mode voltage input common-mode range single-supply operation dual-supply operation 8-pin PDIP PDIP package through-hole package 100 kHz bandwidth bridge sensor current-sense resistor instrumentation signal external feedback resistors semiconductor
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر