Analog Devices

ADF4002BRUZ-RL7 - 400MHz PLL Synthesizer | Analog Devices

MPN: ADF4002BRUZ-RL7 ✓ نشط
3.3 V Vdss Programmable Id 16-pin TSSOP, 4.40 mm width Package 400 MHz Speed
الحد الأدنى للطلب: 1 |

ADF4002BRUZ-RL7 نظرة عامة

The Analog Devices ADF4002BRUZ-RL7 is a 400 MHz phase detector and frequency synthesizer for wireless receiver and transmitter local-oscillator circuits, supplied in a 16-pin TSSOP package. It operates from a 3.3 V power supply and includes a separate charge-pump supply for extended tuning-voltage range. The device combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable N divider in one RF clock-and-timing IC.

A frequency synthesizer is a phase-locked-loop component that locks an output or tuning signal to a stable reference. In the broader product hierarchy, the ADF4002 is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor used to generate or control coherent RF signals. This architecture is useful in wireless upconversion and downconversion paths where stable local oscillators are required by mixers and demodulators.

Key features include 400 MHz bandwidth, a 3.3 V supply, programmable charge-pump currents, a 14-bit reference counter, and a three-wire serial programming interface. Analog and digital lock detection provide monitoring options, while hardware and software power-down functions help reduce consumption when the synthesizer is not required. A separate VP charge-pump supply permits greater tuning-voltage headroom than systems using only the main device supply.

The internal reference and N counters allow division ratios to be programmed for RF synthesis applications. The serial interface uses CLK, DATA, and LE signals, with 24 bits transferred into the appropriate register when the latch-enable signal is asserted. Designers should treat loop bandwidth, reference jitter, charge-pump current, VCO gain, and divider settings as a coordinated system rather than optimizing one parameter independently.

Typical uses include wireless receiver and transmitter local oscillators, frequency conversion in RF front ends, phase and frequency control in communications equipment, and evaluation of PLL loop behavior. In each case, the 400 MHz bandwidth and programmable charge-pump current provide useful flexibility, although the external VCO and passive network determine the final tuning range and phase-noise performance.

For a new layout, place the reference, charge-pump, supply, and decoupling connections according to the manufacturer datasheet. Keep the serial programming traces compact, provide adequate return paths, and treat loop-filter component selection as part of the RF design. The manufacturer's evaluation hardware and software provide a practical way to establish register settings before integrating the synthesizer into a production board.

This page combines manufacturer specifications, sourcing guidance, comparison points, and practical PLL design considerations. It also identifies where pin-level and lifecycle information should be checked directly in the Analog Devices data sheet, Rev. C, and the current product page before a design reaches production.

بدائل مباشرة لـ ADF4002BRUZ-RL7 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ADF4002BRUZ-RL7 (نفس عامل الشكل والبصمة) — يختلف في Package, Serial Interface, Product Type, Reference Counter Resolution.

Analog Devices
Package: 16-lead TSSOP
Serial Interface: 3-wire
قارن مع ADF4002BRUZ-RL7 →
Analog Devices
Package: 16-lead TSSOP
Serial Interface: 3-wire
Product Type: Integer-N PLL frequency synthesizer and phase detector
قارن مع ADF4002BRUZ-RL7 →

ADF4002BRUZ

✅ بديل مباشر
Analog Devices
📦 16-TSSOP
Integer-N PLL frequency synthesizer and phase detector · 400 MHz · 5 MHz to 400 MHz · 3.3 V · Separate VP supply · Programmable · 14 bits · Programmable

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ADF4001SP1BRUZ

✅ بديل مباشر
📦 16-TSSOP
Same TSSOP-16 footprint and three-wire interface, but reduced maximum operating frequency and no ADF4002 programmable charge-pump-current settings

📋 بديل مرجعي (غير موجود في الكتالوج)

ADF4001BRU

✅ بديل مباشر
Analog Devices
📦 16-TSSOP
200 MHz clock generator PLL · 200 MHz · 2.7 V to 5.5 V · 4.5 mA · 3-wire · 13-bit programmable · 14-bit programmable · Programmable

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ADF4002BRUZ-RL7 المواصفات

Product Type Phase detector / PLL frequency synthesizer
Maximum Frequency 400 MHz
Main Supply Voltage 3.3 V
Charge-Pump Supply Separate VP supply
System Compatibility 3 V systems
Reference Counter Resolution 14 bit
Serial Interface 3-wire serial interface
Serial Word Length 24 bit
Charge-Pump Current Programmable
Lock Detection Analog and digital
Power-Down Modes Hardware and software
العلبة 16-pin TSSOP, 4.40 mm width
نوع التركيب Surface mount
Temperature Grade Industrial
Lifecycle Recommendation Recommended for new designs

دليل تكوين أطراف ADF4002BRUZ-RL7 16-pin tssop, 4.40 mm width

تكوين الأطراف لـ ADF4002BRUZ-RL7 (حزمة 16-pin tssop, 4.40 mm width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 16-pin tssop, 4.40 mm width لـ ADF4002BRUZ-RL7

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADF4002BRUZ-RL7.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ADF4002BRUZ-RL7 مناسب لـ 6 التطبيقs: Wireless Transmitter Local Oscillator, Wireless Receiver Downconversion, RF Upconversion and Downconversion, Communications Test Equipment, Industrial RF Frequency Control, PLL Loop Characterization.

🌐

Wireless Transmitter Local Oscillator

The ADF4002BRUZ-RL7 fits wireless transmitter local-oscillator designs that require programmable frequency division and a 400 MHz operating bandwidth. It can compare a divided reference against a divided VCO signal, adjust the VCO tuning voltage through its charge pump, and report lock status through analog or digital detection. Its programmable charge-pump currents help engineers tune loop behavior to the VCO gain and required phase-noise target. The 3.3 V architecture also aligns with many compact RF modules. External loop-filter values, VCO characteristics, isolation, and reference jitter remain the dominant system-level influences on lock range and phase noise.

📡

Wireless Receiver Downconversion

In a wireless receiver downconverter, the ADF4002BRUZ-RL7 can generate the coherent local-oscillator reference required by a mixer. Its programmable reference counter and N divider support synthesis from an available reference source, while the 400 MHz bandwidth accommodates RF PLL operating requirements within that limit. Lock detection provides a signal that can supervise the receiver's local-oscillator state, and power-down can reduce activity when the receiver band is inactive. Final suitability depends on the VCO tuning range, divider ratio, loop filter, isolation from the receiver chain, and acceptable phase-noise and spur levels.

🌐

RF Upconversion and Downconversion

The ADF4002BRUZ-RL7 is suitable for RF upconversion and downconversion blocks that require a programmable, phase-coherent frequency source. Its low-noise phase-frequency detector and precision charge pump work with an external VCO to close the feedback loop, while programmable charge-pump currents provide control over gain and lock behavior. The 14-bit reference counter and programmable N divider enable flexible division ratios. Designers should calculate the complete loop transfer function, verify VCO gain over temperature, and keep the reference and feedback paths away from noisy switching circuitry.

🖥️

Communications Test Equipment

Communications test equipment can use the ADF4002BRUZ-RL7 to create a programmable reference for modulation, vector, or frequency-conversion subsystems. The 400 MHz bandwidth supports RF test-clock generation within the device's operating range, while the 24-bit serial programming model allows instrument firmware to select divider ratios and charge-pump settings. Hardware and software power-down improve power control, and analog plus digital lock indication supports automated calibration and fault handling. For accurate measurements, the external reference should have low phase noise, and the evaluation board is useful for establishing register sequences before implementing a compact custom instrument.

🏭

Industrial RF Frequency Control

Industrial RF systems can employ the ADF4002BRUZ-RL7 when a stable, adjustable oscillator is needed for sensing, excitation, or communication equipment. Its 3.3 V operation, programmable divider chain, and selectable charge-pump currents support adaptation to different VCO gains and frequency plans. Lock detection can be routed into supervisory control logic to prevent operation with an unlocked loop, while power-down supports duty-cycled systems. In industrial environments, account for temperature drift, supply variation, electromagnetic coupling, and grounding. A robust reference and carefully selected loop filter are as important as the synthesizer IC itself.

🔧

PLL Loop Characterization

The ADF4002BRUZ-RL7 is useful in PLL loop-characterization work because its programmable charge-pump currents, divider ratios, and lock-detection functions allow different loop configurations to be evaluated under controlled conditions. Engineers can use the EVAL-ADF4002 platform and associated software to establish register values and compare lock behavior before transferring the design to production hardware. This is especially useful when determining whether a VCO's gain range, reference jitter, or passive filter limits the intended bandwidth. Measurements should separate reference noise from synthesizer noise and verify settling performance across temperature and supply corners.

ملخص المنتجات الموصى بها

ADF4002BRUZ-RL7 Analog Devices يُستخدم في: Wireless Transmitter Local Oscillator, Wireless Receiver Downconversion, RF Upconversion and Downconversion, Communications Test Equipment, Industrial RF Frequency Control, PLL Loop Characterization EVAL-ADF4002 Manufacturer evaluation platform for control and loop testing يُستخدم في: Wireless Transmitter Local Oscillator, RF Upconversion and Downconversion, Communications Test Equipment, PLL Loop Characterization ADF4002BRUZ Analog Devices يُستخدم في: Wireless Receiver Downconversion ADF4001SP1BRUZ Lower-frequency same-family evaluation candidate يُستخدم في: Industrial RF Frequency Control
What is the ADF4002BRUZ-RL7 used for?
The ADF4002BRUZ-RL7 is used to implement local oscillators in wireless receiver and transmitter upconversion and downconversion stages. According to the Analog Devices ADF4002 Data Sheet, Rev. C, it combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable N divider. Its 400 MHz bandwidth makes it suitable for RF frequency-synthesis and phase-control systems requiring a programmable PLL.
What is the operating voltage of ADF4002BRUZ-RL7?
The ADF4002BRUZ-RL7 is designed for operation from a 3.3 V supply and compatibility with 3 V systems. The manufacturer also provides a separate VP charge-pump supply, allowing the charge-pump voltage to be selected independently for extended tuning-voltage range. Use the main and VP supply pins with their datasheet-specified decoupling and grounding arrangements rather than assuming they can be tied together without checking the operating limits.
Where can I download the ADF4002BRUZ-RL7 datasheet PDF?
The official ADF4002BRUZ-RL7 data sheet can be downloaded from the Analog Devices ADF4002 product page or directly from the manufacturer PDF link listed on this page. The document is identified as Data Sheet Rev. C and contains the electrical characteristics, register information, pin descriptions, reference divider, N divider, charge-pump, lock-detection, and application details needed for PLL design.
How is the ADF4002BRUZ-RL7 programmed?
The ADF4002BRUZ-RL7 uses a three-wire serial interface comprising CLK, DATA, and LE. According to the Analog Devices ADF4002 Data Sheet, Rev. C, 24 bits are clocked into the input register on each rising CLK edge and transferred to the appropriate latch when LE goes high. Firmware should include the required clock timing, register address, data-bit order, and latch sequence recommended by the manufacturer.
What are the key specifications of ADF4002BRUZ-RL7 that engineers should know?
The principal specifications are 400 MHz maximum operating frequency, a 3.3 V main supply, programmable charge-pump current, a 14-bit reference counter, analog and digital lock detection, and hardware plus software power-down. The device is packaged in a 16-pin TSSOP with a 4.40 mm body width. These figures come from the Analog Devices ADF4002 Data Sheet, Rev. C, and define the device as a programmable RF PLL frequency synthesizer.
Is ADF4002BRUZ-RL7 suitable for wireless RF local oscillators?
Yes, the ADF4002BRUZ-RL7 is specifically suited to wireless receiver and transmitter local-oscillator implementations. Its 400 MHz bandwidth, programmable reference and N dividers, and programmable charge-pump currents support frequency synthesis above the reference frequency. Actual phase noise, tuning range, and spur performance also depend on the external VCO, reference source, loop filter, isolation, and PCB layout.
What is the difference between ADF4002BRUZ-RL7 and ADF4002BRUZ?
The ADF4002BRUZ-RL7 and ADF4002BRUZ identify the same ADF4002 device in the 16-pin TSSOP family, with the target ordering code carrying the industrial-grade and reel-oriented suffix. Both listings describe a 400 MHz phase detector and frequency synthesizer. For a new production design, confirm the orderable markings, temperature grade, packing method, and customer-specific traceability requirements before treating the order codes as interchangeable.
ADF4002BRUZ-RL7 vs ADF4001SP1BRUZ — which is better for RF PLL designs?
Choose the ADF4002BRUZ-RL7 when the design needs its 400 MHz operating bandwidth and the full ADF4002 programmable charge-pump capability. ADF4001SP1BRUZ is a functional replacement candidate with the same TSSOP-16 footprint and three-wire interface, but its reduced maximum operating frequency and missing ADF4002 charge-pump-current settings require validation. The target part is therefore the closer match for higher-frequency RF synthesis.
When should I choose ADF4002BRUZ-RL7 over ADF4001SP1BRUZ?
Choose ADF4002BRUZ-RL7 when the VCO operating range approaches the ADF4002's 400 MHz bandwidth, when programmable charge-pump current is required for loop tuning, or when analog and digital lock detection are important. Consider ADF4001SP1BRUZ only when its lower frequency capability and reduced charge-pump settings meet the design requirements. Confirm every register and timing difference before using it as a production substitute.
What can replace ADF4002BRUZ-RL7?
ADF4001SP1BRUZ is the closest documented functional replacement candidate because it uses the same TSSOP-16 footprint and three-wire serial interface. However, it has a reduced maximum operating frequency and lacks the ADF4002's programmable charge-pump-current settings, so it is not an unconditional substitute. A drop-in decision must compare the required VCO range, loop bandwidth, register map, lock behavior, and charge-pump requirements.
Is ADF4001SP1BRUZ pin-compatible with ADF4002BRUZ-RL7?
ADF4001SP1BRUZ is documented as sharing the TSSOP-16 footprint and three-wire serial interface of the ADF4002BRUZ family. It can therefore be considered for a board-level substitution after an engineering review. Its reduced maximum operating frequency and absence of the ADF4002's programmable charge-pump-current settings mean that physical pin compatibility does not guarantee functional equivalence in every PLL design.
What is the best Analog Devices equivalent for ADF4002BRUZ-RL7?
ADF4002BRUZ is the closest same-family alternative because it represents the ADF4002 phase detector and frequency synthesizer in the same 16-pin TSSOP package. ADF4001SP1BRUZ is another Analog Devices candidate for lower-frequency designs, but its reduced bandwidth and charge-pump differences require validation. For a new RF design, using an ADF4002 order code generally preserves the intended electrical and register-level behavior.
Where can I buy ADF4002BRUZ-RL7 and what is the lead time?
Use the Request a Quote form on this page to ask about ADF4002BRUZ-RL7 availability, pricing, and lead time for your required quantity and packaging. Current stock, scheduled allocation, and order handling can vary, so obtain a written quotation for the exact suffix rather than relying on an outdated catalog entry. The Analog Devices product page also identifies the ADF4002 as recommended for new designs.
Is ADF4002BRUZ-RL7 in stock?
Stock status for ADF4002BRUZ-RL7 should be confirmed through the Request a Quote form on this page using the exact 16-pin TSSOP ordering code. A listing that shows an in-stock component is not a guaranteed allocation for a production order, particularly when quantities, date codes, and traceability requirements differ. The manufacturer lists the underlying ADF4002 family as recommended for new designs.
How should the ADF4002BRUZ-RL7 be laid out for reliable PLL operation?
Follow the pin-description, decoupling, grounding, and application-circuit guidance in the Analog Devices ADF4002 Data Sheet, Rev. C. Keep the reference input path and charge-pump loop-filter connections compact, provide a low-impedance return for the device ground, and separate sensitive RF and digital return currents where practical. Also validate the external VCO gain, reference jitter, and loop filter because the IC cannot compensate for poor board-level return paths.

بيانات مرجعية هندسية لـ ADF4002BRUZ-RL7 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Select ADF4002BRUZ-RL7 for wireless RF PLL designs that operate within the 400 MHz device bandwidth and benefit from a separate charge-pump supply, programmable charge-pump current, and analog plus digital lock detection. ADF4002BRUZ is the closest same-family choice when the target ordering suffix is unsuitable, while preserving the core function and 16-TSSOP package. Consider ADF4001SP1BRUZ only when the required operating frequency is lower and the design can tolerate reduced bandwidth and the absence of the ADF4002's programmable charge-pump-current settings. ADF4001BRU requires the same engineering review. For every substitute, verify pin assignments, register compatibility, VCO tuning range, lock behavior, reference-divider limits, and power-down timing before releasing a production design.

المقارنة مع البدائل

المعامل هذا المنتج ADF4002BRUZ ADF4001SP1BRUZ ADF4001BRU
Brand Analog Devices Analog Devices Analog Devices Analog Devices
Package 16-TSSOP 16-TSSOP 16-TSSOP 16-TSSOP
Product Type Phase detector / PLL frequency synthesizer Phase detector / PLL frequency synthesizer PLL frequency synthesizer PLL frequency synthesizer

أبرز الفروقات

  • Higher operating bandwidth (مقابلADF4001SP1BRUZ)
  • Programmable charge-pump current (مقابلADF4001SP1BRUZ)
  • Complete lock-status monitoring (مقابلADF4001BRU)
  • Same-family ordering option (مقابلADF4001SP1BRUZ)

ملاحظات التصميم

Use the manufacturer application circuit and pin-description table when assigning PCB tracks. Keep the reference input, charge-pump output, loop-filter components, and device ground connections short, and provide a direct return path for circulating currents. The separate VP connection should be decoupled locally according to the datasheet. Avoid routing serial clock, data, and latch-enable signals beneath noisy switching nodes or between discontinuous ground-plane boundaries.

Do not assume that a shared TSSOP footprint guarantees equivalent PLL behavior. The ADF4001SP1BRUZ has a reduced maximum operating frequency and lacks the ADF4002's programmable charge-pump-current settings. Before substituting it, verify the required VCO range, divider ratios, loop bandwidth, lock-detect polarity, register map, and power-down behavior. For a high-frequency or production-sensitive design, preserve the ADF4002 family unless these differences are explicitly validated.

Design the 3.3 V main rail and separate VP charge-pump rail as distinct supply paths. Their decoupling and return connections should follow the manufacturer reference circuit, with short connections between the capacitor, supply pin, and ground pin. A weak charge-pump supply can reduce tuning range or disturb loop behavior even when the main digital rail measures correctly. Confirm capacitor voltage ratings against both rail tolerances and the maximum VP operating condition.

Treat the reference input and PLL feedback paths as RF-sensitive signals. Terminate and route them away from clocks, switching supplies, and high-current return paths, and use a stable reference with low phase noise. When evaluating phase noise, account for the reference oscillator, divider multiplication, charge-pump noise, VCO noise, and loop filtering rather than attributing the complete result to the ADF4002 alone.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The comparison pages mention RoHS and REACH status, but the exact compliance values are not stated in the available excerpts. Confirm declarations and material documentation with Analog Devices for the exact order code.

تم التحقق من البيانات في: 2026-11-20 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

adf4002bruz datasheet ADF4002BRUZ-RL7 datasheet ADF4002BRUZ-RL7 pinout ADF4002BRUZ-RL7 datasheet pdf ADF4002BRUZ-RL7 specifications ADF4002BRUZ-RL7 equivalent ADF4002BRUZ-RL7 replacement ADF4002BRUZ-RL7 cross reference ADF4002BRUZ-RL7 price ADF4002BRUZ-RL7 stock ADF4002BRUZ-RL7 vs ADF4001SP1BRUZ ADF4002 400MHz PLL application circuit Analog Devices ADF4002BRUZ-RL7 ADF4002BRUZ 16-TSSOP footprint

المكونات والمصطلحات ذات الصلة

Analog Devices ADF4002BRUZ-RL7 ADF4002BRUZ ADF4001SP1BRUZ ADF4001BRU EVAL-ADF4002 phase detector PLL frequency synthesizer frequency synthesizer clock and timing IC phase-locked loop local oscillator programmable divider charge pump reference counter N divider 3-wire serial interface analog lock detection digital lock detection 400 MHz bandwidth 3.3 V supply 16-TSSOP TSSOP package family surface mount wireless receiver wireless transmitter RF upconversion RF downconversion phase noise loop filter
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر