ADF4002BRUZ-RL7 - 400MHz PLL Synthesizer | Analog Devices
N.º de pieza: ADF4002BRUZ-RL7 ✓ ActivoADF4002BRUZ-RL7 Descripción general
A frequency synthesizer is a phase-locked-loop component that locks an output or tuning signal to a stable reference. In the broader product hierarchy, the ADF4002 is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor used to generate or control coherent RF signals. This architecture is useful in wireless upconversion and downconversion paths where stable local oscillators are required by mixers and demodulators.
Key features include 400 MHz bandwidth, a 3.3 V supply, programmable charge-pump currents, a 14-bit reference counter, and a three-wire serial programming interface. Analog and digital lock detection provide monitoring options, while hardware and software power-down functions help reduce consumption when the synthesizer is not required. A separate VP charge-pump supply permits greater tuning-voltage headroom than systems using only the main device supply.
The internal reference and N counters allow division ratios to be programmed for RF synthesis applications. The serial interface uses CLK, DATA, and LE signals, with 24 bits transferred into the appropriate register when the latch-enable signal is asserted. Designers should treat loop bandwidth, reference jitter, charge-pump current, VCO gain, and divider settings as a coordinated system rather than optimizing one parameter independently.
Typical uses include wireless receiver and transmitter local oscillators, frequency conversion in RF front ends, phase and frequency control in communications equipment, and evaluation of PLL loop behavior. In each case, the 400 MHz bandwidth and programmable charge-pump current provide useful flexibility, although the external VCO and passive network determine the final tuning range and phase-noise performance.
For a new layout, place the reference, charge-pump, supply, and decoupling connections according to the manufacturer datasheet. Keep the serial programming traces compact, provide adequate return paths, and treat loop-filter component selection as part of the RF design. The manufacturer's evaluation hardware and software provide a practical way to establish register settings before integrating the synthesizer into a production board.
This page combines manufacturer specifications, sourcing guidance, comparison points, and practical PLL design considerations. It also identifies where pin-level and lifecycle information should be checked directly in the Analog Devices data sheet, Rev. C, and the current product page before a design reaches production.
Alternativas directas para ADF4002BRUZ-RL7 — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con ADF4002BRUZ-RL7 (mismo factor de forma y huella) — difiere en Package, Serial Interface, Product Type, Reference Counter Resolution.
ADF4002BRUZ
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADF4001SP1BRUZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
ADF4001BRU
✅ Sustitución directaConsulte el precio
Ver hoja de datos →ADF4002BRUZ-RL7 Especificaciones
| Product Type | Phase detector / PLL frequency synthesizer |
| Maximum Frequency | 400 MHz |
| Main Supply Voltage | 3.3 V |
| Charge-Pump Supply | Separate VP supply |
| System Compatibility | 3 V systems |
| Reference Counter Resolution | 14 bit |
| Serial Interface | 3-wire serial interface |
| Serial Word Length | 24 bit |
| Charge-Pump Current | Programmable |
| Lock Detection | Analog and digital |
| Power-Down Modes | Hardware and software |
| Encapsulado | 16-pin TSSOP, 4.40 mm width |
| Tipo de montaje | Surface mount |
| Temperature Grade | Industrial |
| Lifecycle Recommendation | Recommended for new designs |
Guía de configuración de pines de ADF4002BRUZ-RL7 16-pin tssop, 4.40 mm width
Configuración de pines para ADF4002BRUZ-RL7 (encapsulado 16-pin tssop, 4.40 mm width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.
No hay datos detallados de patillaje disponibles para ADF4002BRUZ-RL7.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
ADF4002BRUZ-RL7 es adecuado para 6 aplicacións: Wireless Transmitter Local Oscillator, Wireless Receiver Downconversion, RF Upconversion and Downconversion, Communications Test Equipment, Industrial RF Frequency Control, PLL Loop Characterization.
Wireless Transmitter Local Oscillator
The ADF4002BRUZ-RL7 fits wireless transmitter local-oscillator designs that require programmable frequency division and a 400 MHz operating bandwidth. It can compare a divided reference against a divided VCO signal, adjust the VCO tuning voltage through its charge pump, and report lock status through analog or digital detection. Its programmable charge-pump currents help engineers tune loop behavior to the VCO gain and required phase-noise target. The 3.3 V architecture also aligns with many compact RF modules. External loop-filter values, VCO characteristics, isolation, and reference jitter remain the dominant system-level influences on lock range and phase noise.
Recomendado
Wireless Receiver Downconversion
In a wireless receiver downconverter, the ADF4002BRUZ-RL7 can generate the coherent local-oscillator reference required by a mixer. Its programmable reference counter and N divider support synthesis from an available reference source, while the 400 MHz bandwidth accommodates RF PLL operating requirements within that limit. Lock detection provides a signal that can supervise the receiver's local-oscillator state, and power-down can reduce activity when the receiver band is inactive. Final suitability depends on the VCO tuning range, divider ratio, loop filter, isolation from the receiver chain, and acceptable phase-noise and spur levels.
Recomendado
RF Upconversion and Downconversion
The ADF4002BRUZ-RL7 is suitable for RF upconversion and downconversion blocks that require a programmable, phase-coherent frequency source. Its low-noise phase-frequency detector and precision charge pump work with an external VCO to close the feedback loop, while programmable charge-pump currents provide control over gain and lock behavior. The 14-bit reference counter and programmable N divider enable flexible division ratios. Designers should calculate the complete loop transfer function, verify VCO gain over temperature, and keep the reference and feedback paths away from noisy switching circuitry.
Recomendado
Communications Test Equipment
Communications test equipment can use the ADF4002BRUZ-RL7 to create a programmable reference for modulation, vector, or frequency-conversion subsystems. The 400 MHz bandwidth supports RF test-clock generation within the device's operating range, while the 24-bit serial programming model allows instrument firmware to select divider ratios and charge-pump settings. Hardware and software power-down improve power control, and analog plus digital lock indication supports automated calibration and fault handling. For accurate measurements, the external reference should have low phase noise, and the evaluation board is useful for establishing register sequences before implementing a compact custom instrument.
Recomendado
Industrial RF Frequency Control
Industrial RF systems can employ the ADF4002BRUZ-RL7 when a stable, adjustable oscillator is needed for sensing, excitation, or communication equipment. Its 3.3 V operation, programmable divider chain, and selectable charge-pump currents support adaptation to different VCO gains and frequency plans. Lock detection can be routed into supervisory control logic to prevent operation with an unlocked loop, while power-down supports duty-cycled systems. In industrial environments, account for temperature drift, supply variation, electromagnetic coupling, and grounding. A robust reference and carefully selected loop filter are as important as the synthesizer IC itself.
Recomendado
PLL Loop Characterization
The ADF4002BRUZ-RL7 is useful in PLL loop-characterization work because its programmable charge-pump currents, divider ratios, and lock-detection functions allow different loop configurations to be evaluated under controlled conditions. Engineers can use the EVAL-ADF4002 platform and associated software to establish register values and compare lock behavior before transferring the design to production hardware. This is especially useful when determining whether a VCO's gain range, reference jitter, or passive filter limits the intended bandwidth. Measurements should separate reference noise from synthesizer noise and verify settling performance across temperature and supply corners.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para ADF4002BRUZ-RL7 — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | ADF4002BRUZ | ADF4001SP1BRUZ | ADF4001BRU |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Product Type | Phase detector / PLL frequency synthesizer | Phase detector / PLL frequency synthesizer | PLL frequency synthesizer | PLL frequency synthesizer |
Diferenciadores clave
- Higher operating bandwidth (frente a ADF4001SP1BRUZ)
- Programmable charge-pump current (frente a ADF4001SP1BRUZ)
- Complete lock-status monitoring (frente a ADF4001BRU)
- Same-family ordering option (frente a ADF4001SP1BRUZ)
Notas de diseño
Use the manufacturer application circuit and pin-description table when assigning PCB tracks. Keep the reference input, charge-pump output, loop-filter components, and device ground connections short, and provide a direct return path for circulating currents. The separate VP connection should be decoupled locally according to the datasheet. Avoid routing serial clock, data, and latch-enable signals beneath noisy switching nodes or between discontinuous ground-plane boundaries.
Do not assume that a shared TSSOP footprint guarantees equivalent PLL behavior. The ADF4001SP1BRUZ has a reduced maximum operating frequency and lacks the ADF4002's programmable charge-pump-current settings. Before substituting it, verify the required VCO range, divider ratios, loop bandwidth, lock-detect polarity, register map, and power-down behavior. For a high-frequency or production-sensitive design, preserve the ADF4002 family unless these differences are explicitly validated.
Design the 3.3 V main rail and separate VP charge-pump rail as distinct supply paths. Their decoupling and return connections should follow the manufacturer reference circuit, with short connections between the capacitor, supply pin, and ground pin. A weak charge-pump supply can reduce tuning range or disturb loop behavior even when the main digital rail measures correctly. Confirm capacitor voltage ratings against both rail tolerances and the maximum VP operating condition.
Treat the reference input and PLL feedback paths as RF-sensitive signals. Terminate and route them away from clocks, switching supplies, and high-current return paths, and use a stable reference with low phase noise. When evaluating phase noise, account for the reference oscillator, divider multiplication, charge-pump noise, VCO noise, and loop filtering rather than attributing the complete result to the ADF4002 alone.
Información de cumplimiento
The comparison pages mention RoHS and REACH status, but the exact compliance values are not stated in the available excerpts. Confirm declarations and material documentation with Analog Devices for the exact order code.