ADF4002BRUZ-RL7 - 400MHz PLL Synthesizer | Analog Devices
MPN: ADF4002BRUZ-RL7 ✓ 啟用中ADF4002BRUZ-RL7 概覽
A frequency synthesizer is a phase-locked-loop component that locks an output or tuning signal to a stable reference. In the broader product hierarchy, the ADF4002 is a PLL frequency synthesizer, a clock-and-timing IC, and a semiconductor used to generate or control coherent RF signals. This architecture is useful in wireless upconversion and downconversion paths where stable local oscillators are required by mixers and demodulators.
Key features include 400 MHz bandwidth, a 3.3 V supply, programmable charge-pump currents, a 14-bit reference counter, and a three-wire serial programming interface. Analog and digital lock detection provide monitoring options, while hardware and software power-down functions help reduce consumption when the synthesizer is not required. A separate VP charge-pump supply permits greater tuning-voltage headroom than systems using only the main device supply.
The internal reference and N counters allow division ratios to be programmed for RF synthesis applications. The serial interface uses CLK, DATA, and LE signals, with 24 bits transferred into the appropriate register when the latch-enable signal is asserted. Designers should treat loop bandwidth, reference jitter, charge-pump current, VCO gain, and divider settings as a coordinated system rather than optimizing one parameter independently.
Typical uses include wireless receiver and transmitter local oscillators, frequency conversion in RF front ends, phase and frequency control in communications equipment, and evaluation of PLL loop behavior. In each case, the 400 MHz bandwidth and programmable charge-pump current provide useful flexibility, although the external VCO and passive network determine the final tuning range and phase-noise performance.
For a new layout, place the reference, charge-pump, supply, and decoupling connections according to the manufacturer datasheet. Keep the serial programming traces compact, provide adequate return paths, and treat loop-filter component selection as part of the RF design. The manufacturer's evaluation hardware and software provide a practical way to establish register settings before integrating the synthesizer into a production board.
This page combines manufacturer specifications, sourcing guidance, comparison points, and practical PLL design considerations. It also identifies where pin-level and lifecycle information should be checked directly in the Analog Devices data sheet, Rev. C, and the current product page before a design reaches production.
直接替換替代品,適用於 ADF4002BRUZ-RL7 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ADF4002BRUZ-RL7 (相同外形與佔位) — 差異在於 Package, Serial Interface, Product Type, Reference Counter Resolution.
ADF4002BRUZ
✅ 直接替換聯絡詢價
查看資料表 →ADF4001SP1BRUZ
✅ 直接替換📋 參考替代品(不在目錄中)
ADF4001BRU
✅ 直接替換聯絡詢價
查看資料表 →ADF4002BRUZ-RL7 規格
| Product Type | Phase detector / PLL frequency synthesizer |
| Maximum Frequency | 400 MHz |
| Main Supply Voltage | 3.3 V |
| Charge-Pump Supply | Separate VP supply |
| System Compatibility | 3 V systems |
| Reference Counter Resolution | 14 bit |
| Serial Interface | 3-wire serial interface |
| Serial Word Length | 24 bit |
| Charge-Pump Current | Programmable |
| Lock Detection | Analog and digital |
| Power-Down Modes | Hardware and software |
| 封裝 | 16-pin TSSOP, 4.40 mm width |
| 安裝類型 | Surface mount |
| Temperature Grade | Industrial |
| Lifecycle Recommendation | Recommended for new designs |
ADF4002BRUZ-RL7 16-pin tssop, 4.40 mm width 腳位配置指南
ADF4002BRUZ-RL7(16-pin tssop, 4.40 mm width 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: ADF4002BRUZ-RL7.
請參閱 資料表 以查看完整腳位配置。
典型應用
ADF4002BRUZ-RL7 適用於 6 應用s: Wireless Transmitter Local Oscillator, Wireless Receiver Downconversion, RF Upconversion and Downconversion, Communications Test Equipment, Industrial RF Frequency Control, PLL Loop Characterization.
Wireless Transmitter Local Oscillator
The ADF4002BRUZ-RL7 fits wireless transmitter local-oscillator designs that require programmable frequency division and a 400 MHz operating bandwidth. It can compare a divided reference against a divided VCO signal, adjust the VCO tuning voltage through its charge pump, and report lock status through analog or digital detection. Its programmable charge-pump currents help engineers tune loop behavior to the VCO gain and required phase-noise target. The 3.3 V architecture also aligns with many compact RF modules. External loop-filter values, VCO characteristics, isolation, and reference jitter remain the dominant system-level influences on lock range and phase noise.
推薦
Wireless Receiver Downconversion
In a wireless receiver downconverter, the ADF4002BRUZ-RL7 can generate the coherent local-oscillator reference required by a mixer. Its programmable reference counter and N divider support synthesis from an available reference source, while the 400 MHz bandwidth accommodates RF PLL operating requirements within that limit. Lock detection provides a signal that can supervise the receiver's local-oscillator state, and power-down can reduce activity when the receiver band is inactive. Final suitability depends on the VCO tuning range, divider ratio, loop filter, isolation from the receiver chain, and acceptable phase-noise and spur levels.
推薦
RF Upconversion and Downconversion
The ADF4002BRUZ-RL7 is suitable for RF upconversion and downconversion blocks that require a programmable, phase-coherent frequency source. Its low-noise phase-frequency detector and precision charge pump work with an external VCO to close the feedback loop, while programmable charge-pump currents provide control over gain and lock behavior. The 14-bit reference counter and programmable N divider enable flexible division ratios. Designers should calculate the complete loop transfer function, verify VCO gain over temperature, and keep the reference and feedback paths away from noisy switching circuitry.
推薦
Communications Test Equipment
Communications test equipment can use the ADF4002BRUZ-RL7 to create a programmable reference for modulation, vector, or frequency-conversion subsystems. The 400 MHz bandwidth supports RF test-clock generation within the device's operating range, while the 24-bit serial programming model allows instrument firmware to select divider ratios and charge-pump settings. Hardware and software power-down improve power control, and analog plus digital lock indication supports automated calibration and fault handling. For accurate measurements, the external reference should have low phase noise, and the evaluation board is useful for establishing register sequences before implementing a compact custom instrument.
推薦
Industrial RF Frequency Control
Industrial RF systems can employ the ADF4002BRUZ-RL7 when a stable, adjustable oscillator is needed for sensing, excitation, or communication equipment. Its 3.3 V operation, programmable divider chain, and selectable charge-pump currents support adaptation to different VCO gains and frequency plans. Lock detection can be routed into supervisory control logic to prevent operation with an unlocked loop, while power-down supports duty-cycled systems. In industrial environments, account for temperature drift, supply variation, electromagnetic coupling, and grounding. A robust reference and carefully selected loop filter are as important as the synthesizer IC itself.
推薦
PLL Loop Characterization
The ADF4002BRUZ-RL7 is useful in PLL loop-characterization work because its programmable charge-pump currents, divider ratios, and lock-detection functions allow different loop configurations to be evaluated under controlled conditions. Engineers can use the EVAL-ADF4002 platform and associated software to establish register values and compare lock behavior before transferring the design to production hardware. This is especially useful when determining whether a VCO's gain range, reference jitter, or passive filter limits the intended bandwidth. Measurements should separate reference noise from synthesizer noise and verify settling performance across temperature and supply corners.
推薦
推薦產品摘要
工程參考資料,適用於 ADF4002BRUZ-RL7 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ADF4002BRUZ | ADF4001SP1BRUZ | ADF4001BRU |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-TSSOP | 16-TSSOP | 16-TSSOP | 16-TSSOP |
| Product Type | Phase detector / PLL frequency synthesizer | Phase detector / PLL frequency synthesizer | PLL frequency synthesizer | PLL frequency synthesizer |
主要差異化特點
- Higher operating bandwidth (對比ADF4001SP1BRUZ)
- Programmable charge-pump current (對比ADF4001SP1BRUZ)
- Complete lock-status monitoring (對比ADF4001BRU)
- Same-family ordering option (對比ADF4001SP1BRUZ)
設計說明
Use the manufacturer application circuit and pin-description table when assigning PCB tracks. Keep the reference input, charge-pump output, loop-filter components, and device ground connections short, and provide a direct return path for circulating currents. The separate VP connection should be decoupled locally according to the datasheet. Avoid routing serial clock, data, and latch-enable signals beneath noisy switching nodes or between discontinuous ground-plane boundaries.
Do not assume that a shared TSSOP footprint guarantees equivalent PLL behavior. The ADF4001SP1BRUZ has a reduced maximum operating frequency and lacks the ADF4002's programmable charge-pump-current settings. Before substituting it, verify the required VCO range, divider ratios, loop bandwidth, lock-detect polarity, register map, and power-down behavior. For a high-frequency or production-sensitive design, preserve the ADF4002 family unless these differences are explicitly validated.
Design the 3.3 V main rail and separate VP charge-pump rail as distinct supply paths. Their decoupling and return connections should follow the manufacturer reference circuit, with short connections between the capacitor, supply pin, and ground pin. A weak charge-pump supply can reduce tuning range or disturb loop behavior even when the main digital rail measures correctly. Confirm capacitor voltage ratings against both rail tolerances and the maximum VP operating condition.
Treat the reference input and PLL feedback paths as RF-sensitive signals. Terminate and route them away from clocks, switching supplies, and high-current return paths, and use a stable reference with low phase noise. When evaluating phase noise, account for the reference oscillator, divider multiplication, charge-pump noise, VCO noise, and loop filtering rather than attributing the complete result to the ADF4002 alone.
合規資訊
The comparison pages mention RoHS and REACH status, but the exact compliance values are not stated in the available excerpts. Confirm declarations and material documentation with Analog Devices for the exact order code.