ADF4118BRUZ - 3 GHz Integer-N PLL | Analog Devices
MPN: ADF4118BRUZ ✓ نشطADF4118BRUZ نظرة عامة
A phase-locked loop, or PLL, is a feedback-controlled timing system that locks an output frequency to a stable reference. A frequency synthesizer is a PLL-based timing component used to produce programmable RF local-oscillator signals. The ADF4118 family combines a digital phase-frequency detector, precision charge pump, programmable reference divider, programmable A and B counters, and a dual-modulus prescaler for wireless receiver and transmitter signal chains.
The ADF4118BRUZ reaches an RF input frequency of up to 3 GHz and operates from a 2.7 V to 5.5 V power supply. Its integer-N architecture uses programmable counters to establish the required division ratio. A three-wire serial interface supports digital control, while digital lock detect provides a status indication for system sequencing. Separate VP support allows extended tuning-voltage operation in 3 V systems.
The internal architecture is designed for low-noise frequency generation in RF upconversion and downconversion paths. Its programmable reference divider and A/B counters provide flexible ratio programming, while the dual-modulus prescaler supports the required RF input division range. The 3 GHz capability makes the ADF4118BRUZ appropriate for RF communications equipment operating below that upper limit.
Typical uses include wireless receiver local oscillators, wireless transmitter upconversion loops, radio-frequency instrumentation, and low-power RF communication modules. The 2.7 V minimum supply supports compact 3 V systems when the circuit topology and tuning voltage remain within the device's operating limits. The 16-lead TSSOP package also allows reuse of compact surface-mount boards rather than requiring a large through-hole footprint.
When designing around the ADF4118BRUZ, calculate the required prescaler, B-counter, and A-counter values from the reference frequency and target RF input before programming the device. Keep the RF input and charge-pump loop-filter layout compact to reduce phase noise and unwanted coupling. Confirm the maximum input frequency, lock behavior, and component tolerances against the manufacturer datasheet before releasing the PCB.
This page combines the manufacturer's core specifications with application guidance, practical design notes, and a compatibility-focused replacement assessment. It highlights where the ADF4118BRUZ fits RF frequency-synthesis designs and helps engineers distinguish exact package options from functionally similar PLL devices that cannot replace it on an existing PCB.
بدائل مباشرة لـ ADF4118BRUZ — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ADF4118BRUZ (نفس عامل الشكل والبصمة) — يختلف في A Counter, Charge Pump, Package, Device Type, Phase Detector.
ADF4118BRU
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADF4118BRUZ المواصفات
| Device Type | Integer-N RF PLL frequency synthesizer |
| Maximum RF Input Frequency | 3.0 GHz |
| Supply Voltage Range | +2.7 V to +5.5 V |
| تيار التغذية | 6.5 mA |
| Number of Channels | 1 |
| Reference Divider | Programmable |
| A Counter | 5-bit programmable |
| B Counter | Programmable |
| Prescaler | Dual-modulus P/P+1 |
| Phase Detector | Low-noise digital phase-frequency detector |
| Charge Pump | Precision charge pump |
| Serial Interface | 3-wire serial interface |
| Lock Detection | Digital lock detect |
| Power-Down Function | Supported |
| Separate VP Supply | Supported |
| العلبة | 16-lead TSSOP, 4.40 mm width |
| نوع التركيب | Surface Mount |
دليل تكوين أطراف ADF4118BRUZ 16-lead tssop, 4.40 mm width
تكوين الأطراف لـ ADF4118BRUZ (حزمة 16-lead tssop, 4.40 mm width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADF4118BRUZ.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ADF4118BRUZ مناسب لـ 6 التطبيقs: Wireless Receiver Local Oscillator, Wireless Transmitter Upconversion, RF Communication Module, RF Test and Measurement Instrument, Radio-Frequency Data Converter, Industrial RF Control System.
Wireless Receiver Local Oscillator
The ADF4118BRUZ fits a wireless receiver local-oscillator loop that must accept an RF signal as high as 3.0 GHz. Its single-channel integer-N architecture combines a low-noise digital phase-frequency detector, precision charge pump, programmable reference divider, and programmable A and B counters for programmable RF division. The 2.7 V to 5.5 V supply range supports both 3 V and 5 V system partitioning. Place the device near the RF input and loop filter to minimize trace sensitivity, and use digital lock detect to confirm that the receiver mixer can safely enable.
موصى به
Wireless Transmitter Upconversion
The ADF4118BRUZ can generate the programmable local-oscillator reference used in RF transmitter upconversion. Its maximum RF input frequency of 3.0 GHz supports high-frequency RF synthesis while the dual-modulus P/P+1 prescaler and programmable counters establish the required division ratio. A 6.5 mA supply-current specification and a 2.7 V minimum supply are useful for compact power-sensitive transmitters. The 3-wire interface allows the radio controller to set the frequency, while lock detect provides a sequencing signal before the transmit path is enabled.
موصى به
RF Communication Module
The ADF4118BRUZ is appropriate for compact RF communication modules requiring an integer-N local oscillator without a larger mixed-signal synthesizer package. Its 16-lead TSSOP body is 4.40 mm wide and uses surface mounting, which supports dense module layouts. The 2.7 V to 5.5 V operating range accommodates 3 V battery-powered circuitry and higher-voltage front ends. Keep the reference oscillator and charge-pump loop filter close to the device, and use the power-down function to reduce consumption when the radio is idle.
موصى به
RF Test and Measurement Instrument
The ADF4118BRUZ can serve as the programmable RF reference generator inside a compact test or measurement instrument. Its programmable reference divider, 5-bit A counter, programmable B counter, and dual-modulus prescaler allow the required channel ratios to be established for frequencies below the 3.0 GHz maximum. The serial interface simplifies automated control, and digital lock detect can be used as an interlock. Accurate layout, stable reference sourcing, and a well-designed charge-pump loop filter are essential for repeatable phase and frequency performance.
موصى به
Radio-Frequency Data Converter
The ADF4118BRUZ can provide a programmable local oscillator for RF sampling, modulation, or demodulation circuits requiring an integer-N solution. Its 3.0 GHz RF input capability covers high-frequency mixer inputs, while the 6.5 mA supply-current specification supports low-power instrumentation. The device is especially useful where a fixed reference must be converted into multiple programmable RF frequencies. Designers should preserve short RF paths, use a low-inductance loop-filter layout, and verify that the programmed divider values remain valid across the intended channel range.
موصى به
Industrial RF Control System
The ADF4118BRUZ can support industrial RF-control and telemetry systems that use a stable reference to derive a programmable RF operating signal. The single-channel integer-N PLL provides a compact implementation, while the 3-wire interface allows a controller to change operating parameters. Its 2.7 V to 5.5 V supply range is practical for mixed industrial voltage rails, and the TSSOP package simplifies assembly. In a factory environment, apply the device within its specified electrical limits and isolate sensitive RF and charge-pump nodes from noisy power and switching circuitry.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ADF4118BRUZ — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ADF4118BRU |
|---|---|---|
| Manufacturer | Analog Devices | Analog Devices |
| Package | 16-lead TSSOP, 4.40 mm width | 16-lead TSSOP |
| Device Type | Integer-N RF PLL frequency synthesizer | Integer-N frequency synthesizer |
| Maximum RF Input Frequency | 3.0 GHz | 3.0 GHz |
| Supply Voltage Range | +2.7 V to +5.5 V | +2.7 V to +5.5 V |
| Supply Current | 6.5 mA | 6.5 mA |
| Serial Interface | 3-wire serial interface | 3-wire serial interface |
| Number of Channels | 1 | 1 |
| Architecture | Digital PFD, precision charge pump, programmable reference divider, A/B counters, dual-modulus prescaler | Digital PFD, precision charge pump, programmable reference divider, A/B counters, dual-modulus prescaler |
| Power-Down and Lock Detect | Power-down mode and digital lock detect | Power-down mode and digital lock detect |
أبرز الفروقات
- Supports RF input frequencies up to 3.0 GHz (مقابلADF4107BRU-REEL)
- Uses the established ADF4118 integer-N architecture (مقابلADF4154BRU)
- Supports a 3 V-oriented supply arrangement (مقابلADF4116BRUZ)
ملاحظات التصميم
Place the charge-pump components and loop filter directly beside their associated ADF4118BRUZ pins, and minimize the loop-filter trace area. Keep the RF input path short and away from digital serial-interface traces. A compact, symmetrical layout helps preserve intended loop dynamics and reduces coupling from switching or high-current circuitry.
Decouple the supply pins with capacitors selected according to the Analog Devices manufacturer datasheet and the impedance characteristics of the selected reference source. Separate VP handling is important in 3 V systems because it supports extended tuning-voltage operation. Verify the supply, VP, charge-pump, and signal amplitudes under worst-case operating conditions before fabrication.
Do not treat equal package dimensions as proof of drop-in compatibility. Although the ADF4118BRUZ and ADF4107BRU-REEL use 16-lead TSSOP packages, their pin functions and internal architectures differ. Use the ADF411x manufacturer pin-description table and verify reference, RF, serial-interface, charge-pump, and lock-detect assignments before making any substitution.
Program the prescaler, B counter, and A counter from the target reference and RF frequencies before hardware release. Confirm that every channel setting produces a valid divider ratio and that the loop bandwidth supports the intended modulation or hopping rate. Re-evaluate lock time and reference phase-noise requirements whenever the channel spacing or reference frequency changes.
معلومات الامتثال
Compliance attributes are not stated in the manufacturer's product-page excerpt or the ADF411x datasheet excerpt.