ADM213ARS - 4/5 RS-232 Transceiver | Analog Devices
MPN: ADM213ARS ✓ نشطADM213ARS نظرة عامة
An RS-232 transceiver is an interface IC that converts between TTL-compatible logic levels and the bipolar voltage levels used by RS-232 equipment. Its driver channels translate logic states into RS-232 output signals, while its receiver channels translate RS-232 inputs into digital logic. Positioned within the interface-IC hierarchy, this combined transceiver provides the physical signaling layer between data-processing equipment and serial-port peripherals.
The ADM213 combines four driver channels with five receiver channels, making it appropriate for equipment that requires one more receive channel than transmit channel. Two receiver channels remain active during shutdown according to the ADM213 family information, allowing selected incoming signals to be monitored while the main interface operates at reduced power. Separate shutdown and enable pins support controlled operating-state transitions in equipment with managed power rails.
Its CMOS implementation integrates the power-conversion function needed to generate RS-232-level voltage swings from +5 V. The manufacturer describes low-power operation at 15 mW and a low-power shutdown state below 5 µW. The ADM213 family is also identified as latch-up free and supports receiver input levels extending to 30 V, improving tolerance of connected RS-232 signals. A maximum data rate of 120 kB/s is listed in the ADM213 feature summary, while the official product page describes the family as supporting 200 kBPS.
Typical uses include industrial serial-port adapters, data-acquisition equipment, test systems, barcode-reader interfaces, and embedded serial controllers that cannot provide ±12 V. In these systems, the integrated converter reduces external power-supply complexity, while the shutdown function can reduce consumption when the interface is idle. The enable and shutdown inputs can also support coordinated behavior with system power-management circuitry.
Designers should follow the manufacturer's pin-description table when assigning PCB tracks and connect the external charge-pump capacitor at the specified pins. Maintain the required supply decoupling close to VCC and GND, and route driver outputs and receiver inputs away from sensitive analog circuitry. Confirm that the selected cable length, baud rate, logic levels, and shutdown behavior satisfy the system interface requirements.
This page combines the manufacturer's product information with same-footprint upgrade options, application guidance, and design notes intended to make RS-232 hardware decisions more systematic. It highlights the ADM213ARS channel count, supply architecture, power-control features, and package constraints without treating a simple electrical equivalence as proof of complete system compatibility.
بدائل مباشرة لـ ADM213ARS — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ADM213ARS (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, Supply Voltage, Maximum Data Rate.
ADM213ARSZ
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ADM211EARSZ
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ADM213EARSZ-REEL
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
ADM213ARS المواصفات
| Product Type | RS-232 line transceiver |
| Driver Channels | 4 |
| Receiver Channels | 5 |
| جهد التغذية | +5 V |
| معدل البيانات | 200 kBPS |
| Alternative Data Rate | 120 kB/s |
| External Charge Pump Capacitor | 0.1 µF |
| DC-DC Converter | Onboard |
| RS-232 Output Swing | ±9 V |
| Power Consumption | 15 mW |
| Shutdown Power | Less than 5 µW |
| Receivers Active in Shutdown | 2 |
| Receiver Input Level | 30 V |
| Latch-Up | Free |
| Supported Standards | EIA-232-E and V.28 |
| العلبة | 28-SSOP |
| Package Width | 5.30 mm |
| Package Lead Span | 0.209 inch |
| نوع التركيب | Surface mount |
دليل تكوين أطراف ADM213ARS 0.209 inch
تكوين الأطراف لـ ADM213ARS (حزمة 0.209 inch). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ADM213ARS.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ADM213ARS مناسب لـ 6 التطبيقs: Single-Supply RS-232 Serial Adapter, Industrial Data-Acquisition Equipment, Test and Measurement Instrumentation, Barcode and Identification Readers, Embedded Service and Configuration Port, Point-of-Sale and Peripheral Equipment.
Single-Supply RS-232 Serial Adapter
The ADM213ARS fits a compact serial adapter that must produce RS-232 levels from a 5 V system rail. Its onboard DC-to-DC converter generates approximately ±9 V output swing, avoiding separate +12 V and -12 V supplies. Four driver channels support transmit and handshake signals, while five receiver channels can handle incoming data and status indications. The 200 kBPS figure in the manufacturer product page makes the device appropriate for many legacy peripheral and data-acquisition links, subject to cable-length and signal-integrity checks.
موصى به
Industrial Data-Acquisition Equipment
The ADM213ARS is suitable for industrial acquisition equipment with multiple serial channels and a common 5 V supply. Four drivers can operate equipment while five receivers support data, status, and handshake inputs, including two receivers that remain active during shutdown. The approximately ±9 V output swing reduces the need for a bipolar RS-232 supply in compact controller designs. For factory equipment, verify transient protection and grounding at the connector because the transceiver is not a substitute for surge-protection hardware.
موصى به
Test and Measurement Instrumentation
The ADM213ARS can provide a legacy RS-232 control port for oscilloscopes, analyzers, programmable instruments, and laboratory fixtures. A single 5 V rail simplifies instrument power architecture, while the integrated converter supplies the bipolar levels required by RS-232. The combination of four drivers and five receivers permits bidirectional command flow plus hardware-status monitoring. Engineers should use the enable and shutdown controls to manage bus state, and should account for connector-ground noise when placing the transceiver near sensitive measurement circuits.
موصى به
Barcode and Identification Readers
The ADM213ARS is applicable to barcode readers, identification terminals, and handheld equipment that communicates with a host through RS-232. Its four transmit channels can carry commands and handshake signals, and five receive channels provide additional status inputs. Normal power consumption of 15 mW is suitable for compact equipment, while shutdown power below 5 µW can reduce consumption during inactive periods. The package and interface function should be checked against the reader's connector wiring, logic levels, and required polarity of status signals.
موصى به
Embedded Service and Configuration Port
The ADM213ARS can serve as a service or configuration interface on embedded controllers that retain compatibility with RS-232 equipment. The enable and shutdown pins permit firmware or a power-management circuit to isolate the interface during normal operation. Keeping two receiver channels active in shutdown can support wake, status, or presence detection. Because the transceiver operates from 5 V and internally generates approximately ±9 V, it simplifies designs that cannot economically provide a split supply. Firmware must still manage insertion, contention, and protocol timing correctly.
موصى به
Point-of-Sale and Peripheral Equipment
The ADM213ARS is useful in point-of-sale terminals, receipt printers, scales, and other peripherals connected through RS-232. Multiple driver and receiver channels allow data to flow alongside request, acknowledge, and status handshakes. The 28-SSOP package supports compact board layouts, while the integrated converter reduces external power-tree complexity. The product is designed for EIA-232-E and V.28 interfaces, but installers should use the correct cable pinout and verify logic polarity because software-visible RS-232 implementations are not always standardized.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ADM213ARS — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ADM213ARSZ | ADM211EARSZ | ADM213EARSZ-REEL |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-SSOP | 28-SSOP - same | 28-SSOP - same | 28-SSOP - same |
أبرز الفروقات
- Five receivers with two active during shutdown (مقابلADM211EARSZ)
- Single-supply bipolar drive from onboard converter (مقابلADM213ARSZ)
- Low-power shutdown retains selected monitoring channels (مقابلADM213EARSZ-REEL)
ملاحظات التصميم
Use the 28-SSOP footprint from the manufacturer package drawing and assign every connection from the official pin-description table. Place the 0.1 µF charge-pump capacitor and the specified supply bypass capacitors directly beside their associated pins. Keep the return-current path short and use a continuous ground plane beneath the device. Avoid routing driver outputs beneath sensitive receiver inputs because crossover can increase crosstalk and make troubleshooting channel behavior more difficult.
The ADM213ARS uses an onboard DC-to-DC converter to generate approximately ±9 V RS-232 swing from a single 5 V supply. Decouple VCC close to the device with the capacitance and ESR requirements stated in the manufacturer application information. Keep the charge-pump routing compact, and treat the converter as a switching subsystem even though the logic interface is CMOS. A quiet logic rail does not eliminate the need for careful return-current and capacitor placement.
Do not assume that all RS-232 implementations share identical logic polarity or connector assignments. Check the driver and receiver truth tables, enable polarity, shutdown behavior, and receiver thresholds before connecting external equipment. Two receivers remain active during shutdown, so their outputs must remain safe for the controller at all times. Also verify that the system does not apply ±12 V directly to a driver output or permit excessive input voltage beyond the specified receiver limits.
Keep the RS-232 connector and cable interface away from precision analog and high-speed digital sections. Provide a suitable chassis or signal-ground strategy at the connector according to the equipment design, and place protection components at the connector boundary rather than beside the IC. Driver edges can radiate and receiver inputs can respond to external cable noise. A short ground connection, controlled return path, and careful connector selection are often more effective than filtering at the transceiver pins alone.
معلومات الامتثال
The ADM213 family is described as latch-up free and compatible with EIA-232-E and V.28 interfaces. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established from the listed manufacturer information.