Microchip Technology

ATXMEGA256D3-MH - 32MHz AVR MCU with 256KB Flash | Microchip

MPN: ATXMEGA256D3-MH ✓ نشط
1.6 V to 3.6 V Vdss 64-pin VQFN with exposed pad, 9 x 9 mm Package 32 MHz Speed 256 KB (128K x 16) Memory
الحد الأدنى للطلب: 1 |

ATXMEGA256D3-MH نظرة عامة

The Microchip Technology ATXMEGA256D3-MH is a high-performance, low-power 8/16-bit AVR XMEGA D3 microcontroller operating at up to 32 MHz, with 256 KB of ISP Flash memory, 4 KB of EEPROM, and 16 KB of SRAM. It is packaged in a 64-pin VQFN with an exposed thermal pad and a 9 x 9 mm body. The operating voltage range is 1.6 V to 3.6 V, while the industrial temperature range is -40°C to +85°C.

An 8/16-bit AVR microcontroller combines a Harvard-architecture processor with embedded flash, EEPROM, SRAM, and programmable peripherals in one integrated device. The XMEGA D3 family extends the familiar AVR ecosystem with a four-channel event system, programmable multi-level interrupt handling, and high-resolution peripherals for embedded control, communications, and signal-processing applications. Its dual-controller architecture supports deterministic task separation and efficient real-time event handling.

Key features include 256 KB of read-while-write ISP Flash with an 8 KB boot-code section, 4 KB of EEPROM, 16 KB of SRAM, and operation up to 32 MHz. The device provides 16-channel 12-bit ADC capability, advanced timers, communication interfaces, and flexible pin multiplexing. These resources allow the MCU to consolidate functions that might otherwise require several discrete analog and digital components.

The ATxmega256D3 platform combines a 32 MHz core, event-system routing, and programmable interrupt priorities for responsive embedded designs. Read-while-write Flash allows firmware data to remain accessible during programming operations, while the boot-code section supports controlled startup and update workflows. The 1.6 V to 3.6 V operating range is suitable for low-voltage industrial, consumer, and communications equipment operating from regulated 3.3 V rails or compatible lower-voltage sources.

Typical applications include industrial control and factory automation, communication nodes, sensor acquisition systems, compact motor controllers, measurement instruments, and low-power embedded products. Its combination of memory, analog conversion, timing peripherals, and event-driven control makes it particularly useful when board space and deterministic response are important.

PCB design should preserve the exposed-pad thermal and electrical requirements of the VQFN. Place input and output decoupling capacitors close to their associated supply pins, provide a low-impedance ground plane, and follow the manufacturer pin-assignment table when assigning multiplexed I/O functions. Confirm boot, programming, and clock options against the device documentation before releasing production firmware.

This product page combines manufacturer specifications, package and ordering details, supported programming information, comparison guidance, and practical implementation notes to support component selection, schematic review, PCB planning, and sourcing decisions.

بدائل مباشرة لـ ATXMEGA256D3-MH — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ATXMEGA256D3-MH (نفس عامل الشكل والبصمة) — يختلف في Package, Program Memory Type, Supply Voltage Range.

Microchip Technology
Package: 64-TQFP, 14 x 14 mm
Program Memory Type: ISP Flash with read-while-write capability
Supply Voltage Range: 2.7 V to 3.6 V
قارن مع ATXMEGA256D3-MH →

ATXMEGA256D3-MNR

✅ بديل مباشر
📦 64-pin VQFN (9 x 9 mm)
Same ATxmega256D3 family and 64-pin VQFN footprint; ordering-temperature grade differs from the -MH industrial -40°C to +85°C option.

📋 بديل مرجعي (غير موجود في الكتالوج)

ATXMEGA256D3-MH الحدود القصوى والخصائص الكهربائية

Microcontroller Family AVR XMEGA D3
Architecture 8/16-bit AVR
أقصى تردد للساعة 32 MHz
Program Memory Size 256 KB (128K x 16)
Program Memory Type ISP Flash
Boot Code Section 8 KB
Read-While-Write Supported
EEPROM Size 4 KB
SRAM Size 16 KB
Supply Voltage Range 1.6 V to 3.6 V
ADC Resolution 12-bit
ADC Channels 16 channels
Event System 4 channels
العلبة 64-pin VQFN with exposed pad, 9 x 9 mm
نوع التركيب Surface mount
درجة حرارة التشغيل -40°C to +85°C
Packing Media Tray, 260 units
Lead Count 64 pins
Country of Origin South Korea or Taiwan
Green Product Yes

دليل تكوين أطراف ATXMEGA256D3-MH 64-pin vqfn with exposed pad, 9 x 9 mm

تكوين الأطراف لـ ATXMEGA256D3-MH (حزمة 64-pin vqfn with exposed pad, 9 x 9 mm). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.

مخطط توزيع أطراف حزمة 64-pin vqfn with exposed pad, 9 x 9 mm لـ ATXMEGA256D3-MH

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ATXMEGA256D3-MH.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ATXMEGA256D3-MH مناسب لـ 6 التطبيقs: Industrial Sensor Acquisition, Compact Motor Controller, Communication Gateway Node, Measurement and Control Instrument, Automated Test Equipment, Low-Power Embedded Product.

🏭

Industrial Sensor Acquisition

The ATXMEGA256D3-MH fits compact sensor nodes that need fast sampling, local configuration storage, and deterministic control without a separate processor. Its 16-channel 12-bit ADC capability supports analog measurement channels, while 16 KB of SRAM provides working space for filtering and data handling. The 32 MHz AVR core can execute acquisition, filtering, and communication tasks concurrently through interrupt and event mechanisms. A 3.3 V rail falls within the specified 1.6 V to 3.6 V operating range, and the -40°C to +85°C grade suits industrial equipment. Designers should budget analog front-end headroom, reference accuracy, and input settling time for the selected sensor.

⚡

Compact Motor Controller

The ATXMEGA256D3-MH is suitable for compact motor-control modules where timer resources, fast control updates, and limited PCB space are important. Its 32 MHz processing capability supports current sampling, duty-cycle updates, fault handling, and supervisory logic, while the event system can coordinate timing-sensitive internal signals. Sixteen 12-bit ADC channels permit sensing multiple analog quantities associated with motor current, position, temperature, or supply voltage. The device must be paired with suitable power electronics and gate-driver circuitry; the MCU controls rather than replaces the high-current switching stage. Layout should isolate analog returns and power-switching currents from precision measurement paths.

🌐

Communication Gateway Node

The ATXMEGA256D3-MH can serve as a protocol-conversion or communications gateway node where firmware size, peripheral integration, and low-voltage operation are priorities. Its 256 KB ISP Flash accommodates networking stacks, protocol handlers, configuration tables, and bootloader code, while 4 KB of EEPROM preserves calibration or network settings across power cycles. AVR UART, SPI, and I2C resources allow the controller to interface with transceivers, sensors, and storage devices. The 32 MHz core supports responsive packet handling, and read-while-write Flash simplifies applications that update data while executing firmware. Interface signal integrity and protocol timing should be verified against each peripheral specification.

🧩

Measurement and Control Instrument

The ATXMEGA256D3-MH is appropriate for portable measurement instruments that combine signal acquisition, calibration, display support, and communication in a compact controller. The 16-channel 12-bit ADC supports multiple sensor inputs, while 16 KB of SRAM can hold measurement buffers and the 4 KB EEPROM can retain calibration coefficients. Its event system and programmable interrupt architecture help organize time-critical sampling and control operations. The 1.6 V to 3.6 V supply range enables integration with low-voltage analog sections, although each subsystem still needs suitable buffering and grounding. For laboratory or medical designs, validate accuracy, isolation, safety, and compliance requirements at the finished-system level.

🔧

Automated Test Equipment

The ATXMEGA256D3-MH fits automated test equipment requiring deterministic sequencing, programmable I/O, communications, and local nonvolatile storage. Its four-channel event system can coordinate triggers between timers, communications, and external interfaces, while the 32 MHz core performs measurement sequencing and result processing. The 256 KB Flash supports embedded test routines and update logic, and the 16 KB SRAM can buffer intermediate results. The 64-pin VQFN package helps preserve board area in multi-channel systems, although exposed-pad layout is critical. Designers should separate test inputs from high-energy drive stages, use controlled reference sources, and verify timing margins for synchronized measurements.

📱

Low-Power Embedded Product

The ATXMEGA256D3-MH is suitable for compact embedded products that balance processing speed, memory capacity, and low-voltage operation. Its 256 KB Flash and 16 KB SRAM permit local control and communication without external storage, while the four-channel event system reduces polling overhead in responsive designs. Operating from a 1.6 V to 3.6 V supply supports integration with energy-efficient 3.3 V power systems. In battery-powered equipment, use the device’s clock, sleep, and peripheral controls according to the manufacturer’s power-management guidance, and confirm wake-up timing and active current under the final operating profile. Firmware must distinguish fast-start measurement tasks from low-leakage sleep states.

ملخص المنتجات الموصى بها

What is the ATXMEGA256D3-MH?
The ATXMEGA256D3-MH is a Microchip Technology 8/16-bit AVR XMEGA D3 microcontroller with a maximum clock frequency of 32 MHz, 256 KB of ISP Flash, 4 KB of EEPROM, and 16 KB of SRAM. The manufacturer product page identifies the device as a high-performance, low-power embedded controller with read-while-write Flash and a four-channel event system. It is supplied in a 64-pin VQFN package measuring 9 x 9 mm.
What is the operating voltage of ATXMEGA256D3-MH?
The ATXMEGA256D3-MH operates from 1.6 V to 3.6 V. According to the Microchip product page and the Microchip Technology ordering record, this range supports low-voltage embedded systems using regulated 3.3 V rails as well as compatible lower-voltage designs. Designers should keep peripheral supply and I/O levels within the limits defined for the selected operating condition in the manufacturer datasheet.
How much memory does ATXMEGA256D3-MH contain?
The ATXMEGA256D3-MH contains 256 KB of ISP Flash, 4 KB of EEPROM, and 16 KB of SRAM. According to Microchip Technology, the Flash includes an 8 KB boot-code section and supports read-while-write operation. This memory combination allows substantial firmware, nonvolatile configuration data, and working state to be handled without an external memory device.
Where can I download the ATXMEGA256D3-MH datasheet PDF?
The official ATXMEGA256D3-MH documentation is available through the Microchip ATxmega256D3 product page at https://www.microchip.com/en-us/product/ATxmega256D3. Select the ATXMEGA256D3-MH ordering code to obtain the package-specific documentation. The product page also links the device data sheet, package information, and supporting design resources for implementation.
Where can I find the ATXMEGA256D3-MH pinout?
The ATXMEGA256D3-MH pin assignment is published in the package pinout section of the official Microchip ATxmega256D3 documentation. The device uses a 64-pin VQFN with an exposed pad, so the pad designation, supply pins, communications pins, analog inputs, and general-purpose I/O must be assigned from the manufacturer package drawing. Use the ordering-code-specific table when assigning PCB nets.
What peripherals are built into ATXMEGA256D3-MH?
The ATXMEGA256D3-MH integrates 16-channel 12-bit ADC capability, a four-channel event system, timers, and communication peripherals into a 32 MHz AVR device. Microchip describes the XMEGA D3 family as combining programmable multi-level interrupts with event routing. These resources support sensor acquisition, timing, communications, and deterministic control without requiring separate peripheral ICs for many designs.
Is ATXMEGA256D3-MH suitable for industrial control systems?
Yes, the ATXMEGA256D3-MH is suitable for industrial control systems that operate within its specified 1.6 V to 3.6 V supply range and -40°C to +85°C temperature range. Its 32 MHz performance, 12-bit ADC, event system, 256 KB Flash, and 16 KB SRAM support compact control and measurement nodes. Compliance requirements for the finished product must still be assessed independently.
Can ATXMEGA256D3-MHR replace ATXMEGA256D3-MH?
The ATXMEGA256D3-MHR uses the same 64-pin VQFN device family and is listed with 256 KB Flash, 4 KB EEPROM, and 16 KB SRAM, making it the closest documented same-package option. The primary distinction is packing media: -MH is supplied in a tray, while -MHR is supplied in tape-and-reel. Verify programming, flash revision, and production-packing requirements before substitution.
What is the best drop-in replacement for ATXMEGA256D3-MH?
The ATXMEGA256D3-MNR is the closest documented same-package replacement candidate for ATXMEGA256D3-MH because it belongs to the same ATxmega256D3 family and is associated with the same 64-pin QFN footprint. Its temperature qualification differs from the -MH industrial-temperature ordering option. Confirm the complete pin, electrical, flash, and qualification requirements in Microchip documentation before production use.
What can replace ATXMEGA256D3-MH without changing the PCB?
A PCB-compatible replacement must use the same 64-pin QFN footprint and preserve the target device’s peripheral and pin multiplexing. The ATXMEGA256D3-MNR is the closest identified same-family candidate, while ATXMEGA256D3-MHR mainly changes the production packing method. No cross-brand drop-in replacement was identified, so firmware, timing, boot, ADC, and communication behavior also require verification.
When should I choose ATXMEGA256D3-MH over ATXMEGA256D3-MNR?
Choose ATXMEGA256D3-MH when the required temperature range is the industrial -40°C to +85°C grade and tray packaging suits the assembly process. Consider ATXMEGA256D3-MNR when its specified temperature grade covers the application and its ordering conditions fit the supply plan. The choice also depends on availability and qualification, which should be confirmed through the Request a Quote form.
How do I check programming support for ATXMEGA256D3-MH?
Programming support can be checked through Microchip’s programmer and debug ecosystem and the supported-device listing for ATXMEGA256D3-MH. The device uses AVR-family programming interfaces and ISP Flash, so the selected programmer must support the exact device family, package, voltage range, and connection method. Verify the programming header, target voltage, clock behavior, and fuse settings before first board bring-up.
Where can I buy ATXMEGA256D3-MH online?
Use the Request a Quote form on this page to request the Microchip ATXMEGA256D3-MH with the required quantity, tray packaging, and delivery location. The quote team can confirm current supply, lead time, and lot-related information without relying on a static price. For production planning, identify the exact -MH ordering code and the industrial-temperature grade in the purchase request.
What is the price of ATXMEGA256D3-MH?
Current pricing for ATXMEGA256D3-MH should be requested through the Request a Quote form on this page because commercial terms and availability can change with quantity and schedule. The form is the appropriate route for confirming the exact -MH ordering code, 64-pin VQFN packaging, quantity breaks, and expected lead time. No fixed price is asserted in this answer.
What is the lead time and stock status for ATXMEGA256D3-MH?
Current stock and lead time for ATXMEGA256D3-MH should be confirmed through the Request a Quote form on this page. Include the required quantity, target delivery date, acceptable date codes, and whether tray packaging is mandatory. A sourcing response can then reflect the exact ATXMEGA256D3-MH ordering code rather than a generic XMEGA256D3 device or a different package variant.
Is ATXMEGA256D3-MH the same as ATXMEGA256A3U-MH?
No, ATXMEGA256D3-MH and ATXMEGA256A3U-MH belong to different XMEGA families and should not be treated as equivalent simply because both use a 64-pin QFN package. The ATxmega256A3U product is identified as an A3U-series device, while the target is a D3-series part. Their peripheral sets, pin multiplexing, and firmware targets differ, so the ATXMEGA256A3U-MH is not a drop-in replacement.

بيانات مرجعية هندسية لـ ATXMEGA256D3-MH — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose ATXMEGA256D3-MH for compact embedded systems that need a 32 MHz AVR core, 256 KB of read-while-write ISP Flash, 16 KB of SRAM, 12-bit analog acquisition, and an industrial -40°C to +85°C temperature range. Its 64-pin VQFN is appropriate when board area is constrained and the exposed pad can be connected to a well-designed ground plane. ATXMEGA256D3-MNR is the closest same-family candidate for PCB reuse, but its temperature grade and production conditions must be confirmed before approval. ATXMEGA256D3-MHR has the same electrical family and footprint but primarily changes reel packaging, so it is relevant when automated assembly requires tape-and-reel. Do not select ATXMEGA256A3U-MH as a drop-in replacement because the A3U and D3 families have different peripheral and pin-function organizations. For any substitution, verify programming support, boot behavior, clock setup, ADC calibration, communication instances, and firmware compatibility.

المقارنة مع البدائل

المعامل هذا المنتج ATXMEGA256D3-MNR
Brand Microchip Technology Microchip Technology
Package 64-pin VQFN (9 x 9 mm) 64-pin VQFN (9 x 9 mm)
Product Family ATxmega256D3 ATxmega256D3

أبرز الفروقات

  • Large integrated memory configuration (مقابلATXMEGA256D3-MNR)
  • Deterministic event-driven control (مقابلATXMEGA256A3U-MH)
  • Specified industrial temperature grade (مقابلATXMEGA256D3-MNR)
  • Analog and timing integration (مقابلATXMEGA256A3U-MH)

ملاحظات التصميم

The 64-pin VQFN includes an exposed thermal pad that must be connected to the ground plane using the manufacturer’s land-pattern and via guidance. Keep the pad electrically continuous and avoid placing aggressive switching-current paths directly beneath the MCU. Thermal performance depends on board size, copper area, via count, ambient temperature, and switching-node placement, so verify junction-temperature margin in the final layout rather than relying on package dimensions alone.

Place every required decoupling capacitor close to the corresponding AVCC, DVCC, or other supply pins, with a short and low-inductance connection to the ground plane. Separate sensitive analog returns from digital and power-conversion currents where the package permits. Assign externally connected pins only after checking their alternate functions, analog thresholds, and startup states in the official pin-assignment table.

Treat analog inputs, crystal or clock signals, programming signals, and communication interfaces according to their dedicated pin classes. Use a continuous ground reference under routed signals, avoid long parallel returns, and keep switching regulators and fast-edge clock lines separated from precision ADC inputs. If an external crystal is used, follow the required load capacitance, grounding, and placement recommendations in the manufacturer hardware design guidance.

Do not substitute a different XMEGA family solely because it has similar memory or the same pin count. ATxmega256D3-MH and ATxmega256A3U-MH have different family identities and peripheral behavior, even though both use a 64-pin QFN package. Also distinguish -MH tray packaging from -MHR reel packaging, and confirm the required industrial temperature grade, boot configuration, clock source, and fuse settings before approving a substitute.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The Microchip ordering record identifies the device as green, but no specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive qualification statement was provided. AEC-Q100 is not applicable to the standard industrial-temperature ordering option unless separately qualified.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

atxmega256d3 aur ATXMEGA256D3-MH datasheet ATXMEGA256D3-MH datasheet pdf ATXMEGA256D3-MH pinout ATXMEGA256D3-MH equivalent ATXMEGA256D3-MH replacement ATXMEGA256D3-MH footprint ATXMEGA256D3-MH price ATXMEGA256D3-MH stock Microchip ATXMEGA256D3-MH ATXMEGA256D3-MH application circuit ATXMEGA256D3-MH vs ATXMEGA256D3-MNR

المكونات والمصطلحات ذات الصلة

Microchip Technology ATXMEGA256D3-MH ATxmega256D3 ATXMEGA256D3-MNR ATXMEGA256D3-MHR ATXMEGA256A3U-MH AVR XMEGA D3 8/16-bit microcontroller Harvard architecture ISP Flash read-while-write EEPROM SRAM boot code section event system programmable multi-level interrupt 12-bit ADC 32 MHz 1.6 V to 3.6 V 64-pin VQFN QFN family surface mount industrial control
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر