ATXMEGA256D3-MH - 32MHz AVR MCU with 256KB Flash | Microchip
MPN: ATXMEGA256D3-MH ✓ Hoạt độngATXMEGA256D3-MH Tóm tắt
An 8/16-bit AVR microcontroller combines a Harvard-architecture processor with embedded flash, EEPROM, SRAM, and programmable peripherals in one integrated device. The XMEGA D3 family extends the familiar AVR ecosystem with a four-channel event system, programmable multi-level interrupt handling, and high-resolution peripherals for embedded control, communications, and signal-processing applications. Its dual-controller architecture supports deterministic task separation and efficient real-time event handling.
Key features include 256 KB of read-while-write ISP Flash with an 8 KB boot-code section, 4 KB of EEPROM, 16 KB of SRAM, and operation up to 32 MHz. The device provides 16-channel 12-bit ADC capability, advanced timers, communication interfaces, and flexible pin multiplexing. These resources allow the MCU to consolidate functions that might otherwise require several discrete analog and digital components.
The ATxmega256D3 platform combines a 32 MHz core, event-system routing, and programmable interrupt priorities for responsive embedded designs. Read-while-write Flash allows firmware data to remain accessible during programming operations, while the boot-code section supports controlled startup and update workflows. The 1.6 V to 3.6 V operating range is suitable for low-voltage industrial, consumer, and communications equipment operating from regulated 3.3 V rails or compatible lower-voltage sources.
Typical applications include industrial control and factory automation, communication nodes, sensor acquisition systems, compact motor controllers, measurement instruments, and low-power embedded products. Its combination of memory, analog conversion, timing peripherals, and event-driven control makes it particularly useful when board space and deterministic response are important.
PCB design should preserve the exposed-pad thermal and electrical requirements of the VQFN. Place input and output decoupling capacitors close to their associated supply pins, provide a low-impedance ground plane, and follow the manufacturer pin-assignment table when assigning multiplexed I/O functions. Confirm boot, programming, and clock options against the device documentation before releasing production firmware.
This product page combines manufacturer specifications, package and ordering details, supported programming information, comparison guidance, and practical implementation notes to support component selection, schematic review, PCB planning, and sourcing decisions.
Bộ thay thế dễ dàng lắp đặt cho ATXMEGA256D3-MH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATXMEGA256D3-MH (cùng hình factor và footprint) — khác nhau ở Package, Program Memory Type, Supply Voltage Range.
ATXMEGA256D3-MNR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATXMEGA256D3-MH Tỷ lệ tối đa & tính chất điện
| Microcontroller Family | AVR XMEGA D3 |
| Architecture | 8/16-bit AVR |
| Tần số xung maksimum | 32 MHz |
| Program Memory Size | 256 KB (128K x 16) |
| Program Memory Type | ISP Flash |
| Boot Code Section | 8 KB |
| Read-While-Write | Supported |
| EEPROM Size | 4 KB |
| SRAM Size | 16 KB |
| Supply Voltage Range | 1.6 V to 3.6 V |
| ADC Resolution | 12-bit |
| ADC Channels | 16 channels |
| Event System | 4 channels |
| Hộp | 64-pin VQFN with exposed pad, 9 x 9 mm |
| Kiểu lắp đặt | Surface mount |
| Nhiệt độ hoạt động | -40°C to +85°C |
| Packing Media | Tray, 260 units |
| Lead Count | 64 pins |
| Country of Origin | South Korea or Taiwan |
| Green Product | Yes |
Hướng dẫn cấu hình chân ATXMEGA256D3-MH 64-pin vqfn with exposed pad, 9 x 9 mm
Cấu hình chân cho ATXMEGA256D3-MH (64-pin vqfn with exposed pad, 9 x 9 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATXMEGA256D3-MH.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATXMEGA256D3-MH phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Compact Motor Controller, Communication Gateway Node, Measurement and Control Instrument, Automated Test Equipment, Low-Power Embedded Product.
Industrial Sensor Acquisition
The ATXMEGA256D3-MH fits compact sensor nodes that need fast sampling, local configuration storage, and deterministic control without a separate processor. Its 16-channel 12-bit ADC capability supports analog measurement channels, while 16 KB of SRAM provides working space for filtering and data handling. The 32 MHz AVR core can execute acquisition, filtering, and communication tasks concurrently through interrupt and event mechanisms. A 3.3 V rail falls within the specified 1.6 V to 3.6 V operating range, and the -40°C to +85°C grade suits industrial equipment. Designers should budget analog front-end headroom, reference accuracy, and input settling time for the selected sensor.
Được đề xuất
Compact Motor Controller
The ATXMEGA256D3-MH is suitable for compact motor-control modules where timer resources, fast control updates, and limited PCB space are important. Its 32 MHz processing capability supports current sampling, duty-cycle updates, fault handling, and supervisory logic, while the event system can coordinate timing-sensitive internal signals. Sixteen 12-bit ADC channels permit sensing multiple analog quantities associated with motor current, position, temperature, or supply voltage. The device must be paired with suitable power electronics and gate-driver circuitry; the MCU controls rather than replaces the high-current switching stage. Layout should isolate analog returns and power-switching currents from precision measurement paths.
Được đề xuất
Communication Gateway Node
The ATXMEGA256D3-MH can serve as a protocol-conversion or communications gateway node where firmware size, peripheral integration, and low-voltage operation are priorities. Its 256 KB ISP Flash accommodates networking stacks, protocol handlers, configuration tables, and bootloader code, while 4 KB of EEPROM preserves calibration or network settings across power cycles. AVR UART, SPI, and I2C resources allow the controller to interface with transceivers, sensors, and storage devices. The 32 MHz core supports responsive packet handling, and read-while-write Flash simplifies applications that update data while executing firmware. Interface signal integrity and protocol timing should be verified against each peripheral specification.
Được đề xuất
Measurement and Control Instrument
The ATXMEGA256D3-MH is appropriate for portable measurement instruments that combine signal acquisition, calibration, display support, and communication in a compact controller. The 16-channel 12-bit ADC supports multiple sensor inputs, while 16 KB of SRAM can hold measurement buffers and the 4 KB EEPROM can retain calibration coefficients. Its event system and programmable interrupt architecture help organize time-critical sampling and control operations. The 1.6 V to 3.6 V supply range enables integration with low-voltage analog sections, although each subsystem still needs suitable buffering and grounding. For laboratory or medical designs, validate accuracy, isolation, safety, and compliance requirements at the finished-system level.
Được đề xuất
Automated Test Equipment
The ATXMEGA256D3-MH fits automated test equipment requiring deterministic sequencing, programmable I/O, communications, and local nonvolatile storage. Its four-channel event system can coordinate triggers between timers, communications, and external interfaces, while the 32 MHz core performs measurement sequencing and result processing. The 256 KB Flash supports embedded test routines and update logic, and the 16 KB SRAM can buffer intermediate results. The 64-pin VQFN package helps preserve board area in multi-channel systems, although exposed-pad layout is critical. Designers should separate test inputs from high-energy drive stages, use controlled reference sources, and verify timing margins for synchronized measurements.
Được đề xuất
Low-Power Embedded Product
The ATXMEGA256D3-MH is suitable for compact embedded products that balance processing speed, memory capacity, and low-voltage operation. Its 256 KB Flash and 16 KB SRAM permit local control and communication without external storage, while the four-channel event system reduces polling overhead in responsive designs. Operating from a 1.6 V to 3.6 V supply supports integration with energy-efficient 3.3 V power systems. In battery-powered equipment, use the device’s clock, sleep, and peripheral controls according to the manufacturer’s power-management guidance, and confirm wake-up timing and active current under the final operating profile. Firmware must distinguish fast-start measurement tasks from low-leakage sleep states.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATXMEGA256D3-MH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATXMEGA256D3-MNR |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 64-pin VQFN (9 x 9 mm) | 64-pin VQFN (9 x 9 mm) |
| Product Family | ATxmega256D3 | ATxmega256D3 |
Bảo phân biệt quan trọng
- Large integrated memory configuration (vsATXMEGA256D3-MNR)
- Deterministic event-driven control (vsATXMEGA256A3U-MH)
- Specified industrial temperature grade (vsATXMEGA256D3-MNR)
- Analog and timing integration (vsATXMEGA256A3U-MH)
Ghi chú thiết kế
The 64-pin VQFN includes an exposed thermal pad that must be connected to the ground plane using the manufacturer’s land-pattern and via guidance. Keep the pad electrically continuous and avoid placing aggressive switching-current paths directly beneath the MCU. Thermal performance depends on board size, copper area, via count, ambient temperature, and switching-node placement, so verify junction-temperature margin in the final layout rather than relying on package dimensions alone.
Place every required decoupling capacitor close to the corresponding AVCC, DVCC, or other supply pins, with a short and low-inductance connection to the ground plane. Separate sensitive analog returns from digital and power-conversion currents where the package permits. Assign externally connected pins only after checking their alternate functions, analog thresholds, and startup states in the official pin-assignment table.
Treat analog inputs, crystal or clock signals, programming signals, and communication interfaces according to their dedicated pin classes. Use a continuous ground reference under routed signals, avoid long parallel returns, and keep switching regulators and fast-edge clock lines separated from precision ADC inputs. If an external crystal is used, follow the required load capacitance, grounding, and placement recommendations in the manufacturer hardware design guidance.
Do not substitute a different XMEGA family solely because it has similar memory or the same pin count. ATxmega256D3-MH and ATxmega256A3U-MH have different family identities and peripheral behavior, even though both use a 64-pin QFN package. Also distinguish -MH tray packaging from -MHR reel packaging, and confirm the required industrial temperature grade, boot configuration, clock source, and fuse settings before approving a substitute.
Thông tin tuân thủ
The Microchip ordering record identifies the device as green, but no specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive qualification statement was provided. AEC-Q100 is not applicable to the standard industrial-temperature ordering option unless separately qualified.