DS90C185SQ/NOPB - 2.94Gbps LVDS Serializer | Texas Instruments
MPN: DS90C185SQ/NOPB ✓ نشطDS90C185SQ/NOPB نظرة عامة
An FPD-Link serializer is a display-interface device that converts parallel CMOS pixel and control data into a lower-pin-count, differential LVDS transmission format. In the broader electronics hierarchy, the DS90C185 belongs to the serializer and deserializer class of interface ICs, which supports display, GPU, embedded-visual, and portable-computing systems. Differential LVDS signaling reduces signal-integrity demands over long cable or board-trace distances compared with single-ended parallel RGB routing.
The principal DS90C185 features include a 2.94 Gbps maximum data rate, 28 LVCMOS inputs, four LVDS outputs, and a 1.71V to 1.89V operating supply range. The serializer accepts 24 bits of RGB information plus three video-control signals, then sends them through four data lanes and one clock lane. Its reduced-width interface decreases connector and routing complexity in portable battery-powered equipment while preserving high aggregate bandwidth.
This architecture is especially useful when the graphics source and display are separated by a flexible cable, rigid-flex PCB section, or internal display connection. The 2.94 Gbps rate provides sufficient link bandwidth for high-resolution display content, while differential LVDS outputs improve noise immunity compared with an unshielded parallel bus. The low 1.8V supply is consistent with space-constrained embedded systems where power, routing area, and connector count are important design constraints.
Typical uses include notebook and tablet displays, portable instrument displays, industrial human-machine interfaces, embedded control panels, automotive infotainment displays, and portable medical monitoring equipment. In these applications, the serializer reduces the number of conductors crossing the display hinge or internal cable while keeping the graphics-to-display connection organized. System designers should still verify display timing, panel-interface compatibility, lane mapping, and cable length against the manufacturer datasheet.
Layout is critical because the device combines high-speed LVDS outputs with low-voltage digital inputs. Place decoupling capacitors near the supply pins, route the differential clock and data pairs with matched geometry, and keep LVDS traces away from noisy switching nodes. Check the exposed thermal-pad connection and package land pattern carefully to preserve return-path continuity and signal performance.
This product page combines the manufacturer interface description, distributor ordering information, package details, pricing evidence, and engineering guidance to accelerate component evaluation. It also distinguishes true same-footprint replacements from carrier or packaging changes and highlights the parameters that must be checked before substituting a serializer in an existing display design.
بدائل مباشرة لـ DS90C185SQ/NOPB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
DS90C185SQX/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DS90C185SQE/NOPB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←DS90C185SQ/NOPB المواصفات
| Device Type | FPD-Link (LVDS) Serializer |
| Maximum Data Rate | 2.94 Gbps |
| Number of Inputs | 28 inputs |
| عدد المخارج | 4 outputs |
| Input Signal Type | LVCMOS |
| Output Signal Type | FPD-Link and LVDS |
| Supply Voltage Range | 1.71 V to 1.89 V |
| Supported Video Data | 24-bit RGB plus 3 video-control signals |
| LVDS Lane Configuration | 4 data lanes plus 1 clock lane |
| العلبة | 48-pin WQFN (NJV), 6 x 6 mm |
| Exposed Pad | Present |
| نوع التركيب | Surface mount |
| نطاق درجة حرارة التشغيل | -10 °C to +70 °C (TA) |
| Functional Application | Host GPU to display RGB serialization |
| Power Class | Low-power serializer |
| Interface Compatibility | FPD-Link compatible |
| Carrier Option | Custom reel |
| Standard Packaging | Tape and reel |
دليل تكوين أطراف DS90C185SQ/NOPB 48-pin wqfn (njv), 6 x 6 mm
تكوين الأطراف لـ DS90C185SQ/NOPB (حزمة 48-pin wqfn (njv), 6 x 6 mm). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90C185SQ/NOPB.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90C185SQ/NOPB مناسب لـ 6 التطبيقs: Notebook and Tablet Display, Industrial Human-Machine Interface, Automotive Infotainment Display, Portable Medical Monitor, Embedded Control Panel, Portable Test and Measurement Instrument.
Notebook and Tablet Display
The DS90C185SQ/NOPB fits between a host GPU and a compact LCD in notebooks, tablets, and portable computing devices because it serializes 24-bit RGB data and three video-control signals onto four LVDS data lanes plus a clock. Its 2.94 Gbps maximum data rate supports high-bandwidth display transfer, while the 1.71V to 1.89V supply range aligns with low-power portable systems. Reducing parallel conductors simplifies display connectors and protects routing space around hinges or foldable structures.
موصى به
Industrial Human-Machine Interface
The DS90C185SQ/NOPB is suitable for industrial HMIs that transfer rendered graphics from an embedded processor to a remote display across a panel connection. The 28-input LVCMOS side accepts RGB and control information, while four differential outputs reduce the cable width compared with a parallel interface. The 2.94 Gbps capability accommodates demanding display timing, and the 1.8V-class supply supports compact embedded control systems.
موصى به
Automotive Infotainment Display
The DS90C185SQ/NOPB can support the GPU-to-display link in automotive infotainment systems where reduced connector width and robust differential signaling are valuable. It translates 24-bit RGB data plus three control signals into four FPD-Link LVDS data lanes and a clock, enabling a more compact internal display harness. Designers should verify the exact ordering variant's automotive qualification, temperature requirements, display timing, and automotive interface validation before production release.
موصى به
Portable Medical Monitor
The DS90C185SQ/NOPB can reduce the interconnect burden between a portable medical system controller and its local display. Its four-data-plus-clock LVDS output carries 24-bit RGB and three video-control signals at rates up to 2.94 Gbps, while the low 1.8V-class operating range aligns with compact battery-powered equipment. Differential signaling improves resistance to common-mode noise in multi-cable medical-device assemblies, although final signal-integrity and safety validation remains application-specific.
موصى به
Embedded Control Panel
The DS90C185SQ/NOPB is appropriate for embedded control panels where a processor drives a display over an internal cable or rigid-flex board. The serializer reduces the number of conductors required for 24-bit RGB and three control signals, easing routing through a sealed enclosure. Its 48-pin WQFN package and 2.94 Gbps rate support compact, high-bandwidth designs, provided that differential-pair geometry, connector assignments, and panel timing are implemented according to the manufacturer documentation.
موصى به
Portable Test and Measurement Instrument
The DS90C185SQ/NOPB can support a high-resolution display in portable oscilloscopes, analyzers, and field-service instruments. The parallel LVCMOS inputs accept display pixel and control data, and the reduced-width LVDS interface limits the number of conductors crossing an instrument enclosure or hinge. A 2.94 Gbps maximum rate provides useful link headroom, while differential output helps maintain data integrity when the display is connected through an internal cable.
موصى به
بيانات مرجعية هندسية لـ DS90C185SQ/NOPB — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90C185SQX/NOPB | DS90C185SQE/NOPB |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-WQFN (NJV), 6 x 6 mm | 48-WQFN (NJV), 6 x 6 mm | 48-WQFN (NJV), 6 x 6 mm |
| Device Function | Low-power FPD-Link LVDS serializer | Low-power FPD-Link LVDS serializer | Low-power FPD-Link LVDS serializer |
| Maximum Data Rate | 2.94 Gbps | 2.94 Gbps | 2.94 Gbps |
| Number of Inputs | 28 LVCMOS inputs | 28 inputs | 28 inputs |
| Number of Outputs | 4 LVDS outputs | 4 outputs | 4 outputs |
| Supply Voltage Range | 1.71 V to 1.89 V | 1.71 V to 1.89 V | 1.71 V to 1.89 V |
| Supported Video Data | 24-bit RGB plus 3 video-control signals | 24-bit RGB plus 3 video-control signals | 24-bit RGB plus 3 video-control signals |
| Output Interface | 4-data-plus-clock FPD-Link LVDS | 4-data-plus-clock FPD-Link LVDS | 4-data-plus-clock FPD-Link LVDS |
| Operating Temperature Range | -10 °C to +70 °C (TA) | -10 °C to +70 °C (TA) | -10 °C to +70 °C (TA) |
أبرز الفروقات
- Documented exact-device alternatives (مقابلDS90C185SQE/NOPB)
- Cross-reference support for the primary ordering option (مقابلDS90C185SQX/NOPB)
- Reduced-width display connectivity (مقابلDS90C185SQX/NOPB)
ملاحظات التصميم
Create the footprint from the NJV 48-pin WQFN drawing in the Texas Instruments datasheet, including the exposed-pad geometry and its thermal and electrical connection. A nominal QFN-48 footprint can differ in pad dimensions, solder-mask opening, or exposed-pad clearance, so verify every land against the manufacturer package drawing before releasing artwork.
Route each FPD-Link differential pair as a coupled pair with matched impedance, continuous reference-plane return, and minimized stubs. Keep the LVDS clock and data lanes away from switching power nodes and noisy digital return currents. Confirm lane order and connector polarity against the serializer and display-device pin descriptions to avoid an apparently functional link with reversed data pairs.
Place the required bypass capacitors at the DS90C185 supply and ground pins according to the manufacturer application circuit, keeping the connection paths short. Because the device operates from 1.71V to 1.89V, the upstream regulator must remain within that range across tolerance, temperature, and load. Avoid sharing long return paths between the serializer and switching converter outputs.
Validate the complete host-GPU-to-panel link rather than testing only the serializer output. Check input timing, LVDS output amplitude, lane mapping, panel compatibility, and the effects of cable or connector impedance. The 2.94 Gbps specification is a maximum device capability, not proof that every display timing or interconnect will operate without margin.
معلومات الامتثال
A distributor product listing identifies the device as automotive grade, but the exact AEC-Q100 qualification and material-compliance declarations were not available. Confirm current RoHS, REACH, lead-free, halogen-free, conflict-minerals, and qualification status from the manufacturer's compliance documents for the selected ordering code.