DS90CR583MTDX - 65 MHz 28-Bit LVDS Transmitter | TI
MPN: DS90CR583MTDX ✓ نشطDS90CR583MTDX نظرة عامة
An LVDS interface, also called Low Voltage Differential Signaling, is a high-speed electrical interface that transmits data through differential current pairs. Differential signaling improves noise immunity because the receiver evaluates the voltage difference between two conductors rather than the voltage of either conductor relative to ground. In this category, a line driver converts parallel logic into a low-voltage differential serial signal, while a corresponding line receiver reconstructs the parallel data.
The DS90CR583 transmitter samples 28 CMOS/TTL data bits during every cycle of its transmitted clock. Four LVDS pairs carry the converted data, and a separate LVDS link carries the phase-locked transmit clock. This organization supports a 65 MHz LVDS 24-bit color flat-panel-display link while preserving a parallel source interface for the graphics or display controller.
The implementation uses a phase-locked transmit clock so that the data lanes and clock lane remain aligned during transmission. Because the clock is transferred in parallel with the data streams, the receiving system can recover the transmitted word boundaries from the differential interface rather than relying on a separate source-synchronous clock conductor from the transmitter.
Typical applications include LCD monitor panels, industrial HMIs, automotive display links, point-of-sale terminals, and other controller-to-panel assemblies that use a 28-bit parallel pixel bus and an LVDS display link. The transmitter is normally paired with a DS90CR584-family receiver at the panel end. System designers must also provide compatible input and output circuitry, controlled-impedance routing, and connector or cable structures suitable for low-voltage differential signaling.
The main design consideration is that a panel cable and receiver must match the transmitter's data-lane count, clock arrangement, and signaling standard. Review the pin-description table, recommended decoupling, and LVDS routing guidance in the manufacturer datasheet before assigning PCB tracks or laying out the interface.
This page consolidates the interface architecture, verified package information, application guidance, design notes, and drop-in replacement considerations to help engineers evaluate the DS90CR583MTDX before integrating it into a flat-panel-display link.
بدائل مباشرة لـ DS90CR583MTDX — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع DS90CR583MTDX (نفس عامل الشكل والبصمة).
DS90CR285MTDX
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90CR583MTDX المواصفات
| Device Type | LVDS flat-panel-display link transmitter |
| Manufacturer | Texas Instruments |
| Maximum Link Clock Frequency | 65 MHz |
| Parallel Input Width | 28 bits |
| Input Logic | CMOS/TTL |
| LVDS Data Streams | 4 differential data links |
| Clock Link | 1 fifth LVDS link carrying the phase-locked transmit clock |
| Output Signaling | LVDS (Low Voltage Differential Signaling) |
| Display Link Type | LVDS 24-bit color flat-panel-display link |
| Temperature Grade | Commercial |
| Package Code | TSSOP |
| Number of Terminals | 56 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| نوع التركيب | Surface mount |
| الفئة | Line driver / receiver |
| Data Sampling | 28 input bits sampled every transmit-clock cycle |
دليل تكوين أطراف DS90CR583MTDX rectangular
تكوين الأطراف لـ DS90CR583MTDX (حزمة rectangular). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90CR583MTDX.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90CR583MTDX مناسب لـ 6 التطبيقs: LCD Monitor Panel Interfaces, Industrial Human-Machine Interfaces, Point-of-Sale Terminal Displays, Automotive Display Prototyping, Video Game and Kiosk Panels, Flat-Panel Display Test Equipment.
LCD Monitor Panel Interfaces
The DS90CR583MTDX fits controller-to-panel links in LCD monitors because it accepts 28 parallel CMOS/TTL bits and converts them into four LVDS data streams operating at up to 65 MHz. The transmitter also sends a phase-locked clock over the fifth differential link, allowing the panel receiver to recover data alignment. This arrangement replaces many parallel pixel traces with controlled-impedance differential routing, although the exact panel controller and receiver must support the same link format.
موصى به
Industrial Human-Machine Interfaces
Industrial HMIs often place a graphics processor several centimeters from a touch display, making the DS90CR583MTDX suitable for a compact differential connection. Its 65 MHz four-data-lane LVDS output carries 28 sampled input bits per transmit-clock cycle and places the clock on a separate differential pair. Designers should use the manufacturer’s routing guidance and confirm the commercial temperature grade against the enclosure’s actual thermal environment.
موصى به
Point-of-Sale Terminal Displays
Point-of-sale terminals can use the DS90CR583MTDX to connect a display engine to a smaller LCD panel while preserving a wide 28-bit parallel input interface. The resulting four LVDS data pairs plus clock pair reduce PCB routing congestion and support a 65 MHz clocked display link. The receiver, display timing, connector wiring, and cable characteristics must be matched to the transmitter rather than selected only by nominal data rate.
موصى به
Automotive Display Prototyping
The DS90CR583MTDX can support prototype automotive display links where a 28-bit parallel controller output must reach a remote panel over LVDS. Its 65 MHz transmitter architecture and separate clock link are appropriate for evaluating panel timing and connector behavior. Because the device is listed with a commercial temperature grade, production automotive use requires confirmation of the correct ordering variant, temperature limits, qualification status, and lifecycle commitments.
موصى به
Video Game and Kiosk Panels
Compact displays in kiosks, gaming systems, and control panels benefit from the DS90CR583MTDX when the native graphics engine supplies 28 parallel data bits. The transmitter converts those bits into four LVDS pairs and a dedicated clock pair at a 65 MHz link clock, which can simplify enclosure cabling and reduce board area compared with a long parallel bus. Signal-integrity validation remains essential because panel timing, skew, and connector geometry determine usable display reliability.
موصى به
Flat-Panel Display Test Equipment
The DS90CR583MTDX is useful in test systems that emulate or exercise 28-bit-to-LVDS panel links at up to 65 MHz. Engineers can use it to generate four differential data streams and a separate phase-locked clock for cable, connector, and receiver characterization. Calibration equipment must match the link’s electrical conventions, and test fixtures should preserve controlled-impedance routing to avoid mistaking fixture reflections for transmitter or panel failures.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DS90CR583MTDX — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90CR285MTDX |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 56-terminal TSSOP | TSSOP-56 - same package family |
| Device Type | LVDS flat-panel-display link transmitter | 28-bit LVDS channel-link transmitter |
| Maximum Link Clock | 65 MHz | 66 MHz |
| Parallel Input Width | 28 bits | 28 bits |
| Output Signaling | LVDS | LVDS |
| Clock Style | Phase-locked transmit clock on a fifth LVDS link | Rising-edge data-strobe channel link |
| Primary Application | 24-bit color flat-panel-display link | 28-bit channel-link transmission |
أبرز الفروقات
- Dedicated fifth LVDS clock link (مقابلDS90CR285MTDX)
- Direct 28-bit parallel display input (مقابلDS90CR285MTDX)
- Established 56-terminal TSSOP interface (مقابلDS90CR285MTDX)
ملاحظات التصميم
Treat the five LVDS pairs as controlled-impedance differential nets. Route each pair together, maintain a continuous reference plane, and avoid long stubs, excessive vias, and unnecessary layer changes. Keep data-to-clock skew within the link’s timing budget and follow the manufacturer’s recommended interface layout. If the cable is significant, characterize both transmitter outputs and receiver thresholds at the panel end rather than relying only on source-side waveforms.
Place input decoupling and any required clock or configuration components close to their associated device terminals, following the pin-description table and recommended application circuit. Separate the LVDS output routing from sensitive analog or high-speed unrelated circuitry where practical. Verify connector and cable pin assignment so that the four data lanes, clock lane, grounds, and auxiliary connections correspond to the DS90CR584 receiver arrangement.
Do not substitute the part solely because another 28-bit LVDS transmitter uses a similar TSSOP package. Confirm terminal-by-terminal assignment, supply voltage, data-strobe or clock behavior, link timing, receiver compatibility, and connector mapping. The DS90CR583MTDX is a 65 MHz flat-panel-display transmitter, while related channel-link devices may use a different clock architecture or electrical interface even when the parallel data width is identical.
معلومات الامتثال
The device is identified as a commercial-temperature-grade line driver. Confirm RoHS, REACH, lead-free, halogen-free, and automotive qualification status for the exact orderable part before production release.