DS90LV001TLD - 800 Mbps LVDS Buffer | Texas Instruments
MPN: DS90LV001TLD ✗ انتهى عمره الإنتاجيDS90LV001TLD نظرة عامة
The DS90LV001TLD belongs to the LVDS interface IC category, where LVDS means low-voltage differential signaling. LVDS is a differential signaling method used to transmit high-speed data reliably over balanced interconnects while reducing sensitivity to noise and electromagnetic interference. A buffer or re-driver is placed between a source and a receiver when the transmission-line path, connector, backplane, or receiver fan-out cannot be handled directly by the original driver.
Key features include a maximum data rate of 800 Mbps, a typical propagation delay of 2.0 ns according to the component specification, and a supply current of 70 mA. The device provides an output enable function that allows the LVDS output to be placed in TRI-STATE. It is also compatible with the ANSI/TIA/EIA-644-A LVDS standard, providing a defined reference for differential signaling operation.
The DS90LV001 uses a fully differential data path, allowing the output to preserve the logical signal presented at the differential input. This characteristic is useful when signal integrity, common-mode behavior, and repeatable receiver loading matter. The device is intended for single-channel buffering and distribution rather than multi-channel conversion, so a board using several independent links may require one device per link.
Typical applications include LVDS backplane buffering, high-speed point-to-point links, clock distribution through LVDS-compatible paths, and signal conditioning between transmitter and receiver equipment. The 8-WSON package reduces board area compared with the 8-pin SOIC option described for the DS90LV001 family, making it useful when compact routing is required.
When laying out a circuit around the DS90LV001TLD, preserve the controlled-impedance differential transmission-line path, connect the differential pair over a continuous reference plane, and keep the input and output interfaces free of unnecessary branch stubs. The output-enable function should be driven only after the system supply and interface state are valid.
This page combines the DS90LV001TLD electrical characteristics, package information, verified source links, and practical interface guidance to support design selection and sourcing. It also clarifies which documented replacement parts are appropriate for a same-footprint LVDS buffer application and which specifications require engineering review.
بدائل مباشرة لـ DS90LV001TLD — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
DS90LV001TLD/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV001TLDX/NOPB
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV001TLDSE
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV001TLDATR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
DS90LV001TLD المواصفات
| الوظيفة | LVDS-to-LVDS buffer |
| معدل البيانات | 800 Mbps |
| Channel Count | 1 channel |
| Supply Voltage Range | 3 V to 3.6 V |
| Propagation Delay | 2.0 ns |
| تيار التغذية | 70 mA |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| العلبة | 8-WSON (3 mm × 3 mm) |
| نوع التركيب | Surface mount |
| Technology | CMOS |
| Signal Type | LVDS input and LVDS output |
| Output Control | TRI-STATE output enable |
| Typical Propagation Delay | 1.4 ns |
| Peak-to-Peak Jitter | 100 ps at 800 Mbps with PRBS = 2^23 - 1 |
| LVDS Standard | ANSI/TIA/EIA-644-A |
| Package Options in Device Family | 8-pin WSON and SOIC |
| WSON Space Saving | 70% |
دليل تكوين أطراف DS90LV001TLD 8-pin wson and soic
تكوين الأطراف لـ DS90LV001TLD (حزمة 8-pin wson and soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ DS90LV001TLD.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
DS90LV001TLD مناسب لـ 6 التطبيقs: LVDS Backplane Signal Buffering, High-Speed Point-to-Point Link, LVDS Clock Distribution, Industrial Test Equipment Interface, Data Acquisition Backplane, Video and Display Link Conditioning.
LVDS Backplane Signal Buffering
The DS90LV001TLD fits between an LVDS source and backplane receivers when connector loading or unterminated stubs limit signal integrity. Its 800 Mbps data rate and fully differential path preserve the original LVDS signal without converting it to another logic family. Placing the buffer at a card-edge distribution point can provide a controlled, low-impedance LVDS output for the next transmission-line segment. The design should maintain a continuous reference plane, use impedance-controlled routing, and avoid unnecessary branches because the device cannot compensate for an unsuitable channel topology.
موصى به
High-Speed Point-to-Point Link
For a point-to-point LVDS connection, the DS90LV001TLD can act as a receive-and-redrive stage between a remote transmitter and a local receiver. Its listed 2.0 ns propagation delay and 800 Mbps capability make it suitable for high-speed buffering where the interconnect cannot be driven directly by the original source. The main engineering consideration is channel margin: route the pair as a controlled-impedance differential net, minimize connector transitions, and confirm the complete source-buffer-cable-receiver path with signal-integrity analysis.
موصى به
LVDS Clock Distribution
The DS90LV001TLD can buffer a differential LVDS clock when a fan-out branch would otherwise disturb the original source or exceed the desired channel topology. The device supports 800 Mbps signaling and provides an output-enable input for placing the output in TRI-STATE when the clock branch is not active. Because the buffer is single-channel, additional branches or independent clocks require additional devices. Keep each branch short, properly terminated, and routed on an uninterrupted reference plane to avoid introducing reflections into the clock network.
موصى به
Industrial Test Equipment Interface
The DS90LV001TLD is suitable for industrial test and measurement equipment that needs to extend an LVDS signal across a chassis, fixture, or remote module. Its industrial temperature range of -40°C to +85°C supports operation across typical industrial environments, while the compact 8-WSON package saves board area compared with the SOIC option. For reliable fixture communication, use short controlled-impedance routing and account for connector loss, cable skew, and grounding. The output-enable control can also isolate a disconnected or unused branch during test sequencing.
موصى به
Data Acquisition Backplane
A DS90LV001TLD can condition LVDS signals between acquisition cards and a backplane controller where cable, connector, and card-loading effects degrade the original signal. The 800 Mbps maximum data rate accommodates common high-speed acquisition links, while the fully differential architecture retains common-mode noise rejection during regeneration. Designers should allocate device output-enable control to the system sequencing logic and verify receiver thresholds across the complete operating temperature range. Thermal exposure of the compact package must also be considered near high-power backplane circuitry.
موصى به
Video and Display Link Conditioning
The DS90LV001TLD can serve as a transparent LVDS redriver in display or video equipment when a long internal link, connector, or branching load requires regeneration. Its 800 Mbps data rate supports high-speed differential transport, and the 1.4 ns typical propagation delay identified by the manufacturer is useful when system timing is being budgeted. Because this is a buffer rather than a protocol converter, the upstream and downstream devices must use compatible LVDS signaling. Preserve pair geometry, minimize stubs, and validate eye margin across temperature and the actual display cable or board interconnect.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ DS90LV001TLD — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | DS90LV001TLD/NOPB | DS90LV001TLDX/NOPB | DS90LV001TLDSE | DS90LV001TLDATR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Function | LVDS-to-LVDS buffer | 800 Mbps LVDS buffer | 800 Mbps LVDS buffer | DS90LV001 family LVDS buffer | DS90LV001 family LVDS buffer |
أبرز الفروقات
- Documented procurement continuity (مقابلDS90LV001TLD/NOPB)
- Compact high-speed interface implementation (مقابلDS90LV001TLD/NOPB)
- Low-latency transparent buffering (مقابلDS90LV001TLDX/NOPB)
ملاحظات التصميم
Route both LVDS signals as a tightly coupled differential pair over a continuous reference plane. Match the differential impedance and trace spacing to the PCB stack-up, keep the pair length matched, and avoid plane splits or large stubs. The DS90LV001 is intended to buffer a transmission-line signal rather than repair a poorly terminated channel, so connector launches and branch geometry should be evaluated with the actual receiver loading.
Use the manufacturer datasheet and device package drawings when assigning the differential input, differential output, power, ground, output-enable, and exposed-pad connections. Place local supply bypass capacitors close to the device and provide a low-impedance ground connection. Confirm termination values against the selected source and receiver because the correct LVDS termination arrangement depends on the complete system topology rather than on the buffer alone.
Do not treat DS90LV001TLD, DS90LV001TLD/NOPB, and DS90LV001TLDX/NOPB as interchangeable solely by function. Verify the exact orderable suffix, package, pin mapping, lifecycle status, and assembly format in the Texas Instruments ordering information. The original DS90LV001TLD is obsolete, so a controlled transition to the documented substitute is preferable to introducing an unqualified part into a new production design.
Budget the listed 70 mA supply current for the device when sizing the 3 V to 3.6 V rail, and include margin for nearby interface circuitry and temperature-dependent variation. Decouple the supply locally so switching or digital activity elsewhere on the board does not couple into the LVDS signal path. The output-enable input should also remain in a defined state during power transitions to prevent uncontrolled output activity.
معلومات الامتثال
The /NOPB ordering suffix indicates a no-PB-free-suffix ordering option, but explicit RoHS, REACH, halogen-free, and conflict-minerals statements were not identified in the cited component listings. The device is an industrial-temperature interface IC and is not identified as an AEC-Q100 automotive part.