INA2132UA - Dual 36V Difference Amp | Texas Instruments
MPN: INA2132UA ✓ نشطINA2132UA نظرة عامة
A difference amplifier is a specialized amplifier architecture that subtracts two input voltages and multiplies the result by a defined gain. Its role within the amplifier hierarchy is amplifier IC to instrumentation amplifier to low-power difference amplifier. Internal precision resistors establish the nominal gain, while the amplifier rejects signals common to both inputs. This architecture reduces errors in sensor systems where a small differential signal is superimposed on a larger common-mode voltage.
The INA2132UA provides two amplifier channels, a common-mode input range extending from -15 V to 28 V, and a bandwidth of approximately 3 MHz. Its 36 V maximum supply capability supports higher-voltage industrial systems. The 14-pin SOIC package allows straightforward surface-mount assembly, while the -40 °C to +85 °C operating range supports industrial temperature environments.
Each channel combines a precision operational-amplifier core with a laser-trimmed resistor network. This construction supports consistent gain and common-mode rejection without requiring external gain-setting resistors. Because both channels are integrated into one package, designers can use the two amplifiers for complementary measurement channels, differential sensing, or two-stage signal conditioning within the same circuit.
Typical uses include Wheatstone-bridge sensor front ends, motor-current monitoring, differential voltage measurement, and industrial process-control inputs. The common-mode rejection characteristic is particularly useful when the desired signal is much smaller than the voltage shared by both input terminals. The approximately 3 MHz bandwidth also allows the amplifier to process signals beyond static or very slow sensor outputs.
When designing the circuit, verify that input, output, and supply voltages remain within their operating limits at every temperature and tolerance corner. Keep sensitive input routing short, maintain symmetric layouts around the differential pair, and use stable reference and bypass connections to minimize offset and noise errors. A single-supply design also requires careful review of the output common-mode range when the amplified difference can approach either supply rail.
This page consolidates manufacturer specifications, package details, application guidance, and same-footprint replacement information into a design-oriented resource for engineers evaluating the INA2132UA.
بدائل مباشرة لـ INA2132UA — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع INA2132UA (نفس عامل الشكل والبصمة) — يختلف في Operating Temperature Range, Package.
INA2132U
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←INA2132UAE4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
INA2132AQDRDN
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
INA2132U/7880783
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
INA2132UA الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual low-power single-supply difference amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.7 V to 36 V |
| Total Supply Voltage | 36 V maximum |
| Common-Mode Rejection | 76 dB minimum |
| Common-Mode Input Range | -15 V to 28 V |
| Gain Bandwidth | Approximately 3 MHz |
| Gain | 1 dB |
| نطاق درجة حرارة التشغيل | -40 °C to +85 °C |
| العلبة | 14-pin SOIC |
| Package Type | SO-14 surface-mount package |
| نوع التركيب | Surface mount |
| Supply Type | Single supply |
دليل تكوين أطراف INA2132UA so-14 surface-mount package
تكوين الأطراف لـ INA2132UA (حزمة so-14 surface-mount package). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ INA2132UA.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
INA2132UA مناسب لـ 6 التطبيقs: Wheatstone-Bridge Sensor Front End, Motor and Inductor Current Sensing, Industrial Process Voltage Measurement, Balanced Audio and Communication Input, Precision Differential Voltage Acquisition, Portable Sensor and Test Equipment.
Wheatstone-Bridge Sensor Front End
The INA2132UA fits Wheatstone-bridge sensing because each channel subtracts the two bridge-node voltages and rejects their shared component. Its 76 dB minimum common-mode rejection reduces errors when the bridge output is small relative to the excitation voltage, while the approximately 3 MHz bandwidth covers more than static resistive sensors. Place the bridge close to the amplifier, keep the two input paths symmetric, and verify that both bridge nodes remain within the -15 V to 28 V common-mode range. The 2.7 V to 36 V single-supply operation also simplifies instrumentation powered from low-voltage or industrial rails.
موصى به
Motor and Inductor Current Sensing
The INA2132UA can measure a small shunt-voltage difference while rejecting the larger voltage shared by the shunt terminals. Its 76 dB minimum common-mode rejection is advantageous when motor or switching-node voltage varies around a comparatively small current signal, and its approximately 3 MHz bandwidth supports faster current transients than a static sensor interface. Place the shunt and amplifier inputs close together, route the pair as a differential signal, and keep high-current switching nodes away from the input traces. Confirm that the maximum common-mode voltage remains below 28 V for the stated operating configuration.
موصى به
Industrial Process Voltage Measurement
The INA2132UA is appropriate for industrial process signals where a differential measurement is superimposed on a common-mode voltage. The dual configuration supports two related analog channels without requiring two separate packages, and the 36 V maximum supply provides headroom for 24 V industrial systems. Its common-mode rejection reduces sensitivity to shared disturbances, while the 2.7 V lower supply limit permits low-energy measurement nodes. Design the front end so protection-network leakage is balanced on both inputs and verify output swing against the selected single supply at minimum and maximum load conditions.
موصى به
Balanced Audio and Communication Input
The INA2132UA can condition balanced signals in which useful content appears differentially and unwanted noise appears in common. Its 76 dB minimum common-mode rejection improves rejection of shared noise on cable-derived or transformer-derived inputs, while the approximately 3 MHz bandwidth covers a broad range of audio and communication-band signals. Use matched input routing and ground geometry to prevent the amplifier itself from converting differential noise into common-mode error. Check the output swing carefully because a single-supply implementation may require biasing around a midpoint before the signal is sent to downstream converters.
موصى به
Precision Differential Voltage Acquisition
The INA2132UA suits acquisition channels that require subtraction, internal gain consistency, and common-mode suppression close to the sensor. Two integrated channels can measure complementary or related differential voltages, reducing component count and helping maintain matching across a system. The approximately 3 MHz bandwidth provides useful margin for moderately fast sensor signals without requiring a high-speed instrumentation-amplifier architecture. Place input protection close to the pins, balance component values around both channels, and use a low-noise reference arrangement where the downstream converter requires additional precision beyond the amplifier's intrinsic input performance.
موصى به
Portable Sensor and Test Equipment
The low-power, single-supply INA2132UA supports compact battery-powered measurement systems that need two differential analog channels. Its 2.7 V minimum supply allows operation from low-voltage rails, and the 14-pin SOIC package preserves board area relative to using two separate amplifier packages. The 76 dB minimum common-mode rejection helps preserve weak sensor signals in systems with shared ground potential differences. For portable equipment, evaluate the complete power budget under worst-case input conditions and confirm that output headroom is adequate because the input common-mode range extends below ground while the amplifier remains single-supply.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ INA2132UA — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | INA2132U | INA2132UAE4 | INA2132AQDRDN | INA2132U/7880783 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Amplifier Type | Dual low-power single-supply difference amplifier | Dual low-power single-supply difference amplifier | Dual low-power single-supply difference amplifier | Dual difference amplifier | Dual difference amplifier |
| Qualification Grade | Industrial temperature range | Industrial temperature range | Industrial temperature range | Automotive-oriented ordering code | Industrial temperature range |
أبرز الفروقات
- Integrated dual differential measurement channels (مقابلINA2132U)
- High common-mode rejection for difference measurement (مقابلINA2132UAE4)
- Wide common-mode input operating range (مقابلINA2132U/7880783)
- Choice of industrial and automotive-qualified family configurations (مقابلINA2132AQDRDN)
ملاحظات التصميم
Route the two inputs of each channel as a tightly coupled differential pair. Keep both traces similar in length and geometry, connect input protection devices symmetrically, and avoid sharing return paths with switching-current nodes. This reduces conversion of common-mode noise and parasitic imbalance into differential error, which is important because the INA2132UA relies on common-mode rejection rather than input filtering alone.
Validate the entire signal path against the single-supply operating limits. The amplifier accepts inputs from -15 V to 28 V relative to ground, but the usable output range still depends on supply voltage and load. Check minimum output swing, maximum output swing, and settling behavior at the lowest supply. Place supply bypass components close to the relevant pins and use a quiet return path to avoid injecting supply disturbance into the measurement.
Do not assume that the input common-mode rating determines the permitted output swing. Use the manufacturer's operating-characteristics curves and load conditions to verify signal headroom, particularly for low-voltage single-supply designs. Also confirm that selected alternate order codes retain the same pin function and electrical limits; a shared SOIC outline alone does not establish interchangeability.
Protect sensor inputs against ESD, surge, and transient overvoltage without introducing unbalanced leakage. Place protection networks symmetrically and close to the amplifier pins, and confirm that their capacitance, resistance, and temperature behavior do not degrade the approximately 3 MHz bandwidth or the 76 dB common-mode rejection objective.
معلومات الامتثال
The INA2132UA is specified for the -40 °C to +85 °C industrial temperature range. No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was established for this orderable configuration.