INA2132UA - Dual 36V Difference Amp | Texas Instruments
MPN: INA2132UA ✓ 啟用中INA2132UA 概覽
A difference amplifier is a specialized amplifier architecture that subtracts two input voltages and multiplies the result by a defined gain. Its role within the amplifier hierarchy is amplifier IC to instrumentation amplifier to low-power difference amplifier. Internal precision resistors establish the nominal gain, while the amplifier rejects signals common to both inputs. This architecture reduces errors in sensor systems where a small differential signal is superimposed on a larger common-mode voltage.
The INA2132UA provides two amplifier channels, a common-mode input range extending from -15 V to 28 V, and a bandwidth of approximately 3 MHz. Its 36 V maximum supply capability supports higher-voltage industrial systems. The 14-pin SOIC package allows straightforward surface-mount assembly, while the -40 °C to +85 °C operating range supports industrial temperature environments.
Each channel combines a precision operational-amplifier core with a laser-trimmed resistor network. This construction supports consistent gain and common-mode rejection without requiring external gain-setting resistors. Because both channels are integrated into one package, designers can use the two amplifiers for complementary measurement channels, differential sensing, or two-stage signal conditioning within the same circuit.
Typical uses include Wheatstone-bridge sensor front ends, motor-current monitoring, differential voltage measurement, and industrial process-control inputs. The common-mode rejection characteristic is particularly useful when the desired signal is much smaller than the voltage shared by both input terminals. The approximately 3 MHz bandwidth also allows the amplifier to process signals beyond static or very slow sensor outputs.
When designing the circuit, verify that input, output, and supply voltages remain within their operating limits at every temperature and tolerance corner. Keep sensitive input routing short, maintain symmetric layouts around the differential pair, and use stable reference and bypass connections to minimize offset and noise errors. A single-supply design also requires careful review of the output common-mode range when the amplified difference can approach either supply rail.
This page consolidates manufacturer specifications, package details, application guidance, and same-footprint replacement information into a design-oriented resource for engineers evaluating the INA2132UA.
直接替換替代品,適用於 INA2132UA — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: INA2132UA (相同外形與佔位) — 差異在於 Operating Temperature Range, Package.
INA2132U
✅ 直接替換聯絡詢價
查看資料表 →INA2132UAE4
✅ 直接替換📋 參考替代品(不在目錄中)
INA2132AQDRDN
✅ 直接替換📋 參考替代品(不在目錄中)
INA2132U/7880783
✅ 直接替換📋 參考替代品(不在目錄中)
INA2132UA 最大額定值與電氣特性
| Amplifier Type | Dual low-power single-supply difference amplifier |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.7 V to 36 V |
| Total Supply Voltage | 36 V maximum |
| Common-Mode Rejection | 76 dB minimum |
| Common-Mode Input Range | -15 V to 28 V |
| Gain Bandwidth | Approximately 3 MHz |
| Gain | 1 dB |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 14-pin SOIC |
| Package Type | SO-14 surface-mount package |
| 安裝類型 | Surface mount |
| Supply Type | Single supply |
INA2132UA so-14 surface-mount package 腳位配置指南
INA2132UA(so-14 surface-mount package 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: INA2132UA.
請參閱 資料表 以查看完整腳位配置。
典型應用
INA2132UA 適用於 6 應用s: Wheatstone-Bridge Sensor Front End, Motor and Inductor Current Sensing, Industrial Process Voltage Measurement, Balanced Audio and Communication Input, Precision Differential Voltage Acquisition, Portable Sensor and Test Equipment.
Wheatstone-Bridge Sensor Front End
The INA2132UA fits Wheatstone-bridge sensing because each channel subtracts the two bridge-node voltages and rejects their shared component. Its 76 dB minimum common-mode rejection reduces errors when the bridge output is small relative to the excitation voltage, while the approximately 3 MHz bandwidth covers more than static resistive sensors. Place the bridge close to the amplifier, keep the two input paths symmetric, and verify that both bridge nodes remain within the -15 V to 28 V common-mode range. The 2.7 V to 36 V single-supply operation also simplifies instrumentation powered from low-voltage or industrial rails.
推薦
Motor and Inductor Current Sensing
The INA2132UA can measure a small shunt-voltage difference while rejecting the larger voltage shared by the shunt terminals. Its 76 dB minimum common-mode rejection is advantageous when motor or switching-node voltage varies around a comparatively small current signal, and its approximately 3 MHz bandwidth supports faster current transients than a static sensor interface. Place the shunt and amplifier inputs close together, route the pair as a differential signal, and keep high-current switching nodes away from the input traces. Confirm that the maximum common-mode voltage remains below 28 V for the stated operating configuration.
推薦
Industrial Process Voltage Measurement
The INA2132UA is appropriate for industrial process signals where a differential measurement is superimposed on a common-mode voltage. The dual configuration supports two related analog channels without requiring two separate packages, and the 36 V maximum supply provides headroom for 24 V industrial systems. Its common-mode rejection reduces sensitivity to shared disturbances, while the 2.7 V lower supply limit permits low-energy measurement nodes. Design the front end so protection-network leakage is balanced on both inputs and verify output swing against the selected single supply at minimum and maximum load conditions.
推薦
Balanced Audio and Communication Input
The INA2132UA can condition balanced signals in which useful content appears differentially and unwanted noise appears in common. Its 76 dB minimum common-mode rejection improves rejection of shared noise on cable-derived or transformer-derived inputs, while the approximately 3 MHz bandwidth covers a broad range of audio and communication-band signals. Use matched input routing and ground geometry to prevent the amplifier itself from converting differential noise into common-mode error. Check the output swing carefully because a single-supply implementation may require biasing around a midpoint before the signal is sent to downstream converters.
推薦
Precision Differential Voltage Acquisition
The INA2132UA suits acquisition channels that require subtraction, internal gain consistency, and common-mode suppression close to the sensor. Two integrated channels can measure complementary or related differential voltages, reducing component count and helping maintain matching across a system. The approximately 3 MHz bandwidth provides useful margin for moderately fast sensor signals without requiring a high-speed instrumentation-amplifier architecture. Place input protection close to the pins, balance component values around both channels, and use a low-noise reference arrangement where the downstream converter requires additional precision beyond the amplifier's intrinsic input performance.
推薦
Portable Sensor and Test Equipment
The low-power, single-supply INA2132UA supports compact battery-powered measurement systems that need two differential analog channels. Its 2.7 V minimum supply allows operation from low-voltage rails, and the 14-pin SOIC package preserves board area relative to using two separate amplifier packages. The 76 dB minimum common-mode rejection helps preserve weak sensor signals in systems with shared ground potential differences. For portable equipment, evaluate the complete power budget under worst-case input conditions and confirm that output headroom is adequate because the input common-mode range extends below ground while the amplifier remains single-supply.
推薦
推薦產品摘要
工程參考資料,適用於 INA2132UA — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | INA2132U | INA2132UAE4 | INA2132AQDRDN | INA2132U/7880783 |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC | 14-pin SOIC |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Amplifier Type | Dual low-power single-supply difference amplifier | Dual low-power single-supply difference amplifier | Dual low-power single-supply difference amplifier | Dual difference amplifier | Dual difference amplifier |
| Qualification Grade | Industrial temperature range | Industrial temperature range | Industrial temperature range | Automotive-oriented ordering code | Industrial temperature range |
主要差異化特點
- Integrated dual differential measurement channels (對比INA2132U)
- High common-mode rejection for difference measurement (對比INA2132UAE4)
- Wide common-mode input operating range (對比INA2132U/7880783)
- Choice of industrial and automotive-qualified family configurations (對比INA2132AQDRDN)
設計說明
Route the two inputs of each channel as a tightly coupled differential pair. Keep both traces similar in length and geometry, connect input protection devices symmetrically, and avoid sharing return paths with switching-current nodes. This reduces conversion of common-mode noise and parasitic imbalance into differential error, which is important because the INA2132UA relies on common-mode rejection rather than input filtering alone.
Validate the entire signal path against the single-supply operating limits. The amplifier accepts inputs from -15 V to 28 V relative to ground, but the usable output range still depends on supply voltage and load. Check minimum output swing, maximum output swing, and settling behavior at the lowest supply. Place supply bypass components close to the relevant pins and use a quiet return path to avoid injecting supply disturbance into the measurement.
Do not assume that the input common-mode rating determines the permitted output swing. Use the manufacturer's operating-characteristics curves and load conditions to verify signal headroom, particularly for low-voltage single-supply designs. Also confirm that selected alternate order codes retain the same pin function and electrical limits; a shared SOIC outline alone does not establish interchangeability.
Protect sensor inputs against ESD, surge, and transient overvoltage without introducing unbalanced leakage. Place protection networks symmetrically and close to the amplifier pins, and confirm that their capacitance, resistance, and temperature behavior do not degrade the approximately 3 MHz bandwidth or the 76 dB common-mode rejection objective.
合規資訊
The INA2132UA is specified for the -40 °C to +85 °C industrial temperature range. No explicit RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was established for this orderable configuration.