ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas
MPN: ISL8485ECP ✓ نشطISL8485ECP نظرة عامة
A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers.
The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring.
The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration.
Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture.
PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process.
This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.
بدائل مباشرة لـ ISL8485ECP — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلISL8485ECP المواصفات
| Product Type | 1/1 half-duplex RS-422 and RS-485 transceiver |
| جهد التغذية | 5 V |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Communication Mode | Half-duplex |
| Supported Standards | RS-422 and RS-485 |
| ESD Protection | ±15 kV |
| Driver Fault Protection | On-chip driver output short-circuit current limit |
| Thermal Protection | On-chip thermal shutdown |
| Logic Technology | CMOS |
| العلبة | 8-pin PDIP |
| نوع التركيب | Through-hole |
دليل تكوين أطراف ISL8485ECP 8-pin pdip
تكوين الأطراف لـ ISL8485ECP (حزمة 8-pin pdip). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISL8485ECP.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ISL8485ECP مناسب لـ 6 التطبيقs: Industrial Sensor Networking, PLC Communication Interface, Building Automation Controller, Motor Control Monitoring, Laboratory Instrument Communication, Remote Data Acquisition.
Industrial Sensor Networking
The ISL8485ECP fits non-isolated industrial sensor nodes that communicate through a 5 V RS-485 bus. Its one-driver and one-receiver arrangement supports a single half-duplex channel, while ±15 kV ESD protection adds useful protection when a sensor cable leaves the equipment enclosure. The short-circuit current limit and thermal shutdown improve robustness if two bus drivers contend. A designer should still select appropriate bus protection, grounding, and termination components because transceiver ESD protection does not replace a complete surge-protection strategy.
موصى به
PLC Communication Interface
The ISL8485ECP can connect a controller board to a field bus carrying commands and sensor data through one RS-485 differential channel. Operating from 5 V allows integration with compatible controller logic, and the 8-pin PDIP package is practical for through-hole industrial control boards. Driver current limiting and thermal shutdown help the interface survive contention during firmware updates or misconfigured addressing. Validate the bus direction-control method, baud-rate limit, and logic thresholds against the manufacturer datasheet before finalizing the controller firmware.
موصى به
Building Automation Controller
The ISL8485ECP suits building-automation controller boards that exchange measurements and commands over a wired RS-485 network. The half-duplex, one-driver and one-receiver arrangement can support a shared bus when the controller handles direction control and arbitration correctly. ESD protection to ±15 kV is particularly relevant where the network cable passes near motors, switches, and building service equipment. Confirm operating-temperature requirements and determine whether the installation requires galvanic isolation across building zones.
موصى به
Motor Control Monitoring
The ISL8485ECP can provide a robust communication path between a motor-control board and an external monitoring or parameter-tuning system. The differential bus helps reject common-mode noise, while the driver current limit and thermal shutdown protect the transceiver during output contention. The 5 V transceiver can be placed near a controller that uses compatible logic levels. Designers should keep the bus pair away from switching-node traces and verify whether regenerative braking or motor-return paths require additional isolation or surge protection.
موصى به
Laboratory Instrument Communication
The ISL8485ECP is appropriate for a compact laboratory instrument that needs a wired command interface over RS-422 or RS-485. A single transceiver channel is sufficient for half-duplex master operation, and ±15 kV ESD protection helps manage electrostatic discharge encountered during routine instrument connections. The PDIP package supports simple through-hole prototyping and repair. Confirm the required signaling rate, receiver sensitivity, and cable length against the electrical characteristics before selecting the device for a precision measurement front end.
موصى به
Remote Data Acquisition
The ISL8485ECP supports a remote data-acquisition unit that must collect measurements from a wired sensor bus. Its one-driver and one-receiver configuration supports bidirectional half-duplex data exchange, while the driver current limit and thermal shutdown improve reliability when a remote cable is connected incorrectly. For long cables, use a controlled differential layout, place termination at the physical ends of the bus, and avoid excessive stub lengths. The design should include biasing so an idle differential bus remains in a valid state.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ISL8485ECP — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Product Type | 1/1 half-duplex RS-422 and RS-485 transceiver |
| Supply Voltage | 5 V |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Communication Mode | Half-duplex |
| Supported Standards | RS-422 and RS-485 |
| ESD Protection | ±15 kV |
| Protection Features | Driver short-circuit current limit and on-chip thermal shutdown |
| Logic Technology | CMOS |
| Package | 8-pin PDIP |
| Mounting Type | Through-hole |
| Brand | Renesas Electronics |
أبرز الفروقات
- Integrated bus-contention protection (مقابلISL8490)
- Single-channel half-duplex implementation (مقابلISL8491)
- Field-bus ESD protection (مقابلGeneric RS-485 transceiver without a stated ±15 kV rating)
ملاحظات التصميم
Route the driver and receiver inputs as a closely coupled differential pair with symmetrical geometry and continuous ground reference. Keep the pair away from switching power nodes, relays, and high-current motor-return paths. Place termination and any fail-safe bias components according to their position in the bus topology rather than directly beside every node. Long branch stubs increase reflected signals and can reduce the usable communication distance.
Do not treat the ±15 kV ESD rating as permission to omit external bus protection. Determine whether the installation requires TVS devices, common-mode chokes, surge arrestors, or isolation based on cable length and the external environment. Also ensure that only one driver actively drives the bus during normal operation; the internal current limit and thermal shutdown improve survival during contention but are not substitutes for correct bus arbitration.
Place the transceiver and its local supply-decoupling components close to the connector entry path while keeping the differential route continuous. Use a low-impedance ground plane and provide a direct return path beneath or adjacent to the differential pair. Verify the footprint against the 8-pin PDIP drawing, including row spacing and pin-1 orientation, and avoid adding copper or jumpers that change the high-frequency return path between the transceiver and connector.
معلومات الامتثال
The verified product pages do not state the requested compliance classifications. No compliance status has been inferred from the component category or package.