Renesas Electronics

ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas

MPN: ISL8485ECP ✓ 啟用中
5 V Vdss RS-422 and RS-485 Rds(on) 8-pin PDIP Package
MOQ: 1 |

ISL8485ECP 概覽

The Renesas Electronics ISL8485ECP is a single half-duplex RS-485 and RS-422 line transceiver IC operating from a 5 V supply and supplied in an 8-pin PDIP package. It combines one driver and one receiver in one device, supports ESD protection to ±15 kV, and includes driver short-circuit current limiting and on-chip thermal shutdown for improved robustness during bus contention.

A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers.

The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring.

The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration.

Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture.

PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process.

This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.

直接替換替代品,適用於 ISL8485ECP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此產品無可直接替換的替代品。

申請替代品

ISL8485ECP 規格

Product Type 1/1 half-duplex RS-422 and RS-485 transceiver
供應電壓 5 V
Driver Count 1 driver
Receiver Count 1 receiver
Communication Mode Half-duplex
Supported Standards RS-422 and RS-485
ESD Protection ±15 kV
Driver Fault Protection On-chip driver output short-circuit current limit
Thermal Protection On-chip thermal shutdown
Logic Technology CMOS
封裝 8-pin PDIP
安裝類型 Through-hole

ISL8485ECP 8-pin pdip 腳位配置指南

ISL8485ECP(8-pin pdip 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

ISL8485ECP 的 8-pin pdip 封裝腳位圖

無詳細腳位定義資料: ISL8485ECP.

請參閱 資料表 以查看完整腳位配置。

典型應用

ISL8485ECP 適用於 6 應用s: Industrial Sensor Networking, PLC Communication Interface, Building Automation Controller, Motor Control Monitoring, Laboratory Instrument Communication, Remote Data Acquisition.

🏭

Industrial Sensor Networking

The ISL8485ECP fits non-isolated industrial sensor nodes that communicate through a 5 V RS-485 bus. Its one-driver and one-receiver arrangement supports a single half-duplex channel, while ±15 kV ESD protection adds useful protection when a sensor cable leaves the equipment enclosure. The short-circuit current limit and thermal shutdown improve robustness if two bus drivers contend. A designer should still select appropriate bus protection, grounding, and termination components because transceiver ESD protection does not replace a complete surge-protection strategy.

🏭

PLC Communication Interface

The ISL8485ECP can connect a controller board to a field bus carrying commands and sensor data through one RS-485 differential channel. Operating from 5 V allows integration with compatible controller logic, and the 8-pin PDIP package is practical for through-hole industrial control boards. Driver current limiting and thermal shutdown help the interface survive contention during firmware updates or misconfigured addressing. Validate the bus direction-control method, baud-rate limit, and logic thresholds against the manufacturer datasheet before finalizing the controller firmware.

🏭

Building Automation Controller

The ISL8485ECP suits building-automation controller boards that exchange measurements and commands over a wired RS-485 network. The half-duplex, one-driver and one-receiver arrangement can support a shared bus when the controller handles direction control and arbitration correctly. ESD protection to ±15 kV is particularly relevant where the network cable passes near motors, switches, and building service equipment. Confirm operating-temperature requirements and determine whether the installation requires galvanic isolation across building zones.

⚡

Motor Control Monitoring

The ISL8485ECP can provide a robust communication path between a motor-control board and an external monitoring or parameter-tuning system. The differential bus helps reject common-mode noise, while the driver current limit and thermal shutdown protect the transceiver during output contention. The 5 V transceiver can be placed near a controller that uses compatible logic levels. Designers should keep the bus pair away from switching-node traces and verify whether regenerative braking or motor-return paths require additional isolation or surge protection.

🔧

Laboratory Instrument Communication

The ISL8485ECP is appropriate for a compact laboratory instrument that needs a wired command interface over RS-422 or RS-485. A single transceiver channel is sufficient for half-duplex master operation, and ±15 kV ESD protection helps manage electrostatic discharge encountered during routine instrument connections. The PDIP package supports simple through-hole prototyping and repair. Confirm the required signaling rate, receiver sensitivity, and cable length against the electrical characteristics before selecting the device for a precision measurement front end.

📡

Remote Data Acquisition

The ISL8485ECP supports a remote data-acquisition unit that must collect measurements from a wired sensor bus. Its one-driver and one-receiver configuration supports bidirectional half-duplex data exchange, while the driver current limit and thermal shutdown improve reliability when a remote cable is connected incorrectly. For long cables, use a controlled differential layout, place termination at the physical ends of the bus, and avoid excessive stub lengths. The design should include biasing so an idle differential bus remains in a valid state.

推薦產品摘要

ISL8490 Related device in the same Renesas transceiver datasheet 用於: Industrial Sensor Networking, PLC Communication Interface, Building Automation Controller, Motor Control Monitoring, Laboratory Instrument Communication, Remote Data Acquisition ISL8491 Related device in the same Renesas transceiver datasheet 用於: Industrial Sensor Networking, PLC Communication Interface, Building Automation Controller, Motor Control Monitoring, Laboratory Instrument Communication, Remote Data Acquisition
What is the ISL8485ECP?
The ISL8485ECP is a Renesas Electronics single half-duplex transceiver IC combining one driver and one receiver for RS-422 and RS-485 communication. According to the Renesas ISL8485, ISL8490, ISL8491 datasheet, it operates from a 5 V supply, provides ESD protection to ±15 kV, and uses on-chip driver short-circuit current limiting and thermal shutdown to withstand bus contention.
What package does the ISL8485ECP use?
The ISL8485ECP is packaged in an 8-pin PDIP package for through-hole PCB assembly. The product listing identifies the package as 8-PDIP, while the family datasheet covers the ISL8485, ISL8490, and ISL8491 devices. Use the manufacturer pin-description table to assign each PCB connection and verify orientation from the package markings.
What are the key specifications of ISL8485ECP?
The ISL8485ECP is a 5 V, one-driver and one-receiver, half-duplex RS-422/RS-422 transceiver with ±15 kV ESD protection. The Renesas family datasheet also identifies driver output short-circuit current limiting and on-chip thermal shutdown as key protection features. Maximum data rate, operating temperature, supply current, slew rate, and logic thresholds should be read from the exact device ordering table and electrical characteristics.
Where can I download the ISL8485ECP datasheet PDF?
The official ISL8485ECP datasheet is available through the Renesas document page titled “ISL8485, ISL8490, ISL8491 Datasheet.” Open that manufacturer document to review the device description, electrical characteristics, timing, pin assignments, and application information. The document number and revision should be taken from the downloaded file itself, and the exact ISL8485ECP ordering code should be confirmed before releasing a PCB design.
Where is the ISL8485ECP pinout located?
The ISL8485ECP pinout is located in the pin-description table of the Renesas ISL8485, ISL8490, ISL8491 datasheet. The ISL8485ECP uses an 8-pin PDIP package, so the table and package drawing must be used together when numbering PCB holes. Assign power, ground, driver, receiver, enable, and control functions exactly as shown for the selected device rather than inferring them from a related family member.
Is the ISL8485ECP suitable for industrial RS-485 systems?
The ISL8485ECP is suitable for many non-isolated industrial RS-485 interfaces because it supports a 5 V supply, differential RS-485 signaling, ±15 kV ESD protection, driver current limiting, and thermal shutdown. Industrial suitability still depends on the complete system: verify operating temperature, isolation requirements, surge level, cable length, grounding strategy, and the regulator or protection components used around the transceiver.
How does the ISL8485ECP protect against RS-485 bus contention?
The ISL8485ECP protects against bus contention by limiting driver output current and using on-chip thermal shutdown. According to the Renesas ISL8485, ISL8490, ISL8491 datasheet, the RS-485 specification requires drivers to survive worst-case bus contentions without damage. Application design must still prevent sustained contention where possible and provide protection appropriate to the installation environment.
What can replace the ISL8485ECP?
A valid replacement for the ISL8485ECP must be a pin-compatible 8-pin PDIP RS-485/RS-422 transceiver with comparable supply voltage, driver and receiver performance, timing, and protection ratings. The targeted cross-reference results do not identify a verified substitute with a confirmed footprint and parameter match, so no drop-in replacement is asserted on this page. Request a Quote on this page for sourcing support, and require the prospective manufacturer to confirm pinout and timing equivalence before substitution.
What is the best Renesas equivalent for ISL8485ECP?
The Renesas ISL8490 and ISL8491 appear in the same family datasheet, but the manufacturer document alone does not establish that either is a pin-compatible substitute for the ISL8485ECP. Compare their pin functions, operating modes, propagation delay, slew-rate limits, supply current, and shutdown behavior against the ISL8485ECP before considering either device. Use the family datasheet and the exact ordering tables to make that determination.
Is ISL8485ECP the same as ISL8490 or ISL8491?
No conclusion of equivalence should be made solely because the ISL8485ECP, ISL8490, and ISL8491 are covered by the same Renesas datasheet. The ISL8485ECP is specifically identified as a 1/1 half-duplex RS-422/RS-485 transceiver in an 8-PDIP package. Confirm whether the other devices have different pin assignments, channel counts, enable functions, or timing before treating them as equivalents or replacements.
When should I choose ISL8485ECP instead of another RS-485 transceiver?
Choose the ISL8485ECP when a design requires a single half-duplex RS-422/RS-485 channel, a 5 V supply, an 8-pin PDIP footprint, and a transceiver with ±15 kV ESD protection, driver current limiting, and thermal shutdown. Choose another device when the interface requires galvanic isolation, multiple channels, a surface-mount package, a different logic voltage, a larger data rate, or specific automotive qualification.
Where can I buy ISL8485ECP and check current stock?
Use the Request a Quote form on this page to request current availability, unit pricing, and lead time for the Renesas ISL8485ECP. The component is identified as an 8-pin PDIP half-duplex RS-422/RS-485 transceiver, so the quote should identify that exact MPN and package. Ask for lot-date, traceability, and lifecycle details appropriate to the quantity and production schedule of your assembly.
What is the price of ISL8485ECP?
Current unit pricing for the Renesas ISL8485ECP should be obtained through the Request a Quote form on this page. The exact MPN is ISL8485ECP in the 8-PDIP package, and quote requests should specify the required quantity, packing method, and production schedule. Volume breaks and delivery terms should be confirmed at the time of quotation rather than inferred from a generic part-family listing.
What is the lead time for ISL8485ECP?
The current lead time for the Renesas ISL8485ECP should be requested through the Request a Quote form on this page. Include the annual and build quantities because procurement timing can vary with quantity, inventory, and manufacturing schedule. Also state whether reel, tray, or other approved packing is required, although the verified component identity for this MPN is the 8-pin PDIP package.
Is ISL8485ECP in stock?
Use the Request a Quote form on this page to check current stock and allocation status for the exact Renesas ISL8485ECP. Stock confirmation should be tied to the complete ordering code, 8-pin PDIP package, and requested quantity. For production planning, request a dated supply commitment and note any package, marking, or traceability requirements before approving the purchase order.

工程參考資料,適用於 ISL8485ECP — 比較、設計指引及合規資訊。

選型指南

Choose the ISL8485ECP when the PCB requires one half-duplex RS-422 or RS-485 channel, a 5 V supply, an 8-pin PDIP footprint, and built-in protection against bus contention and electrostatic discharge. The driver current limit and thermal shutdown are valuable when field cabling creates a realistic risk of contention or fault energy. Select the ISL8490 or ISL8491 only after comparing their exact pin assignments, timing, enable behavior, and electrical limits with the ISL8485ECP. Do not choose a different transceiver merely because it also supports RS-485: data rate, receiver threshold, supply current, shutdown behavior, package, and isolation requirements can make it unsuitable. If the equipment crosses galvanic-isolation boundaries, requires multiple bus channels, or uses a surface-mount assembly, specify a device designed for those requirements rather than treating any bus transceiver as interchangeable.

與替代品比較

參數 本產品
Product Type 1/1 half-duplex RS-422 and RS-485 transceiver
Supply Voltage 5 V
Driver Count 1 driver
Receiver Count 1 receiver
Communication Mode Half-duplex
Supported Standards RS-422 and RS-485
ESD Protection ±15 kV
Protection Features Driver short-circuit current limit and on-chip thermal shutdown
Logic Technology CMOS
Package 8-pin PDIP
Mounting Type Through-hole
Brand Renesas Electronics

主要差異化特點

  • Integrated bus-contention protection (對比ISL8490)
  • Single-channel half-duplex implementation (對比ISL8491)
  • Field-bus ESD protection (對比Generic RS-485 transceiver without a stated ±15 kV rating)

設計說明

Route the driver and receiver inputs as a closely coupled differential pair with symmetrical geometry and continuous ground reference. Keep the pair away from switching power nodes, relays, and high-current motor-return paths. Place termination and any fail-safe bias components according to their position in the bus topology rather than directly beside every node. Long branch stubs increase reflected signals and can reduce the usable communication distance.

Do not treat the ±15 kV ESD rating as permission to omit external bus protection. Determine whether the installation requires TVS devices, common-mode chokes, surge arrestors, or isolation based on cable length and the external environment. Also ensure that only one driver actively drives the bus during normal operation; the internal current limit and thermal shutdown improve survival during contention but are not substitutes for correct bus arbitration.

Place the transceiver and its local supply-decoupling components close to the connector entry path while keeping the differential route continuous. Use a low-impedance ground plane and provide a direct return path beneath or adjacent to the differential pair. Verify the footprint against the 8-pin PDIP drawing, including row spacing and pin-1 orientation, and avoid adding copper or jumpers that change the high-frequency return path between the transceiver and connector.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The verified product pages do not state the requested compliance classifications. No compliance status has been inferred from the component category or package.

資料驗證日期: 2026-11-15 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

ISL8485ECP datasheet ISL8485ECP pinout ISL8485ECP datasheet pdf ISL8485ECP specifications ISL8485ECP equivalent ISL8485ECP replacement ISL8485ECP drop-in substitute ISL8485ECP vs ISL8490 ISL8485ECP vs ISL8491 Renesas ISL8485ECP ISL8485ECP PDIP-8 footprint ISL8485ECP price ISL8485ECP stock ISL8485ECP RS-485 transceiver ISL8485ECP application circuit

相關元件與詞彙

Renesas Electronics ISL8485ECP ISL8490 ISL8491 RS-485 RS-422 half-duplex transceiver line transceiver interface IC semiconductor differential signaling driver receiver CMOS 5 V power supply ESD protection ±15 kV short-circuit current limiting thermal shutdown 8-pin PDIP through-hole package industrial automation building automation data acquisition motor control
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情