ISL8485ECP - 5V Half-Duplex RS-485/422 IC | Renesas
부품 번호: ISL8485ECP ✓ 활성ISL8485ECP 개요
A transceiver IC is an interface device that converts logic-level signals into differential bus signals and reconstructs logic-level data from a differential bus. RS-485 supports balanced, multipoint communication over longer cables and is commonly deployed in industrial automation, building controls, instrumentation, and communications equipment. RS-422 provides a related differential signaling method commonly used for point-to-point links. The ISL8485ECP belongs to the interface-IC hierarchy alongside isolated and non-isolated bus transceivers.
The headline features are a 5 V supply, one driver and one receiver, half-duplex operation, ±15 kV ESD protection, and an 8-pin PDIP package. Driver output current limiting helps the device withstand contention without external damage, while thermal shutdown provides an additional response to excessive internal power dissipation. These protections are particularly valuable on cables that leave the controlled equipment enclosure and connect to longer field wiring.
The ISL8485ECP is one member of the Renesas ISL8485, ISL8490, and ISL8491 datasheet family. Devices in this family use low-power, high-speed or slew-rate-limited RS-485 and RS-422 transceiver architectures. The exact enable, shutdown, and speed behavior should be selected from the pin-description and timing tables in the manufacturer datasheet for the intended bus configuration.
Typical applications include industrial sensor networks, programmable logic controller interfaces, building automation equipment, motor-control systems, and instrumentation links. The device is especially appropriate where a compact non-isolated transceiver is required at a 5 V logic rail. Systems needing galvanic isolation, higher data rates, or a different bus topology require a different transceiver architecture.
PCB implementation requires close attention to the ground and differential-signal traces. Route the bus pair as a controlled-impedance differential pair, minimize stub lengths, and place termination and biasing components at locations appropriate to the network topology. Do not use the PDIP package in a design that assumes a surface-mount assembly process.
This page organizes the device identity, electrical characteristics, bus-transceiver use cases, protection considerations, and package-level selection factors into an engineering-focused guide. The manufacturer datasheet remains the controlling reference for pin functions, timing, limits, and application circuits.
드롭인 대체품: ISL8485ECP — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 제품에는 사용 가능한 드롭인 대체품이 없습니다.
대체품 요청ISL8485ECP 사양
| Product Type | 1/1 half-duplex RS-422 and RS-485 transceiver |
| 공급 전압 | 5 V |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Communication Mode | Half-duplex |
| Supported Standards | RS-422 and RS-485 |
| ESD Protection | ±15 kV |
| Driver Fault Protection | On-chip driver output short-circuit current limit |
| Thermal Protection | On-chip thermal shutdown |
| Logic Technology | CMOS |
| 패키지 | 8-pin PDIP |
| 실장 유형 | Through-hole |
ISL8485ECP 8-pin pdip 핀 구성 가이드
ISL8485ECP(8-pin pdip 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.
다음에 대한 상세 핀아웃 데이터 없음: ISL8485ECP.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
ISL8485ECP 적합 용도: 6 애플리케이션s: Industrial Sensor Networking, PLC Communication Interface, Building Automation Controller, Motor Control Monitoring, Laboratory Instrument Communication, Remote Data Acquisition.
Industrial Sensor Networking
The ISL8485ECP fits non-isolated industrial sensor nodes that communicate through a 5 V RS-485 bus. Its one-driver and one-receiver arrangement supports a single half-duplex channel, while ±15 kV ESD protection adds useful protection when a sensor cable leaves the equipment enclosure. The short-circuit current limit and thermal shutdown improve robustness if two bus drivers contend. A designer should still select appropriate bus protection, grounding, and termination components because transceiver ESD protection does not replace a complete surge-protection strategy.
추천
PLC Communication Interface
The ISL8485ECP can connect a controller board to a field bus carrying commands and sensor data through one RS-485 differential channel. Operating from 5 V allows integration with compatible controller logic, and the 8-pin PDIP package is practical for through-hole industrial control boards. Driver current limiting and thermal shutdown help the interface survive contention during firmware updates or misconfigured addressing. Validate the bus direction-control method, baud-rate limit, and logic thresholds against the manufacturer datasheet before finalizing the controller firmware.
추천
Building Automation Controller
The ISL8485ECP suits building-automation controller boards that exchange measurements and commands over a wired RS-485 network. The half-duplex, one-driver and one-receiver arrangement can support a shared bus when the controller handles direction control and arbitration correctly. ESD protection to ±15 kV is particularly relevant where the network cable passes near motors, switches, and building service equipment. Confirm operating-temperature requirements and determine whether the installation requires galvanic isolation across building zones.
추천
Motor Control Monitoring
The ISL8485ECP can provide a robust communication path between a motor-control board and an external monitoring or parameter-tuning system. The differential bus helps reject common-mode noise, while the driver current limit and thermal shutdown protect the transceiver during output contention. The 5 V transceiver can be placed near a controller that uses compatible logic levels. Designers should keep the bus pair away from switching-node traces and verify whether regenerative braking or motor-return paths require additional isolation or surge protection.
추천
Laboratory Instrument Communication
The ISL8485ECP is appropriate for a compact laboratory instrument that needs a wired command interface over RS-422 or RS-485. A single transceiver channel is sufficient for half-duplex master operation, and ±15 kV ESD protection helps manage electrostatic discharge encountered during routine instrument connections. The PDIP package supports simple through-hole prototyping and repair. Confirm the required signaling rate, receiver sensitivity, and cable length against the electrical characteristics before selecting the device for a precision measurement front end.
추천
Remote Data Acquisition
The ISL8485ECP supports a remote data-acquisition unit that must collect measurements from a wired sensor bus. Its one-driver and one-receiver configuration supports bidirectional half-duplex data exchange, while the driver current limit and thermal shutdown improve reliability when a remote cable is connected incorrectly. For long cables, use a controlled differential layout, place termination at the physical ends of the bus, and avoid excessive stub lengths. The design should include biasing so an idle differential bus remains in a valid state.
추천
추천 제품 요약
엔지니어링 참조 데이터: ISL8485ECP — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 |
|---|---|
| Product Type | 1/1 half-duplex RS-422 and RS-485 transceiver |
| Supply Voltage | 5 V |
| Driver Count | 1 driver |
| Receiver Count | 1 receiver |
| Communication Mode | Half-duplex |
| Supported Standards | RS-422 and RS-485 |
| ESD Protection | ±15 kV |
| Protection Features | Driver short-circuit current limit and on-chip thermal shutdown |
| Logic Technology | CMOS |
| Package | 8-pin PDIP |
| Mounting Type | Through-hole |
| Brand | Renesas Electronics |
주요 차별점
- Integrated bus-contention protection (vs ISL8490)
- Single-channel half-duplex implementation (vs ISL8491)
- Field-bus ESD protection (vs Generic RS-485 transceiver without a stated ±15 kV rating)
설계 노트
Route the driver and receiver inputs as a closely coupled differential pair with symmetrical geometry and continuous ground reference. Keep the pair away from switching power nodes, relays, and high-current motor-return paths. Place termination and any fail-safe bias components according to their position in the bus topology rather than directly beside every node. Long branch stubs increase reflected signals and can reduce the usable communication distance.
Do not treat the ±15 kV ESD rating as permission to omit external bus protection. Determine whether the installation requires TVS devices, common-mode chokes, surge arrestors, or isolation based on cable length and the external environment. Also ensure that only one driver actively drives the bus during normal operation; the internal current limit and thermal shutdown improve survival during contention but are not substitutes for correct bus arbitration.
Place the transceiver and its local supply-decoupling components close to the connector entry path while keeping the differential route continuous. Use a low-impedance ground plane and provide a direct return path beneath or adjacent to the differential pair. Verify the footprint against the 8-pin PDIP drawing, including row spacing and pin-1 orientation, and avoid adding copper or jumpers that change the high-frequency return path between the transceiver and connector.
규정 준수 정보
The verified product pages do not state the requested compliance classifications. No compliance status has been inferred from the component category or package.