Renesas Electronics

ISL8488IB-T - 250kbps Full-Duplex RS-485/422 | Renesas

MPN: ISL8488IB-T ✓ نشط
5 V Vdss RS-485 and RS-422 Rds(on) 8-SOIC Package
الحد الأدنى للطلب: 1 |

ISL8488IB-T نظرة عامة

Renesas Electronics ISL8488IB-T is a single RS-485/RS-422 transceiver operating from a 5 V supply, with one transmitter and one receiver in an 8-SOIC package. The device supports data rates up to 250 kbps and provides full-duplex balanced communication without separate receiver-enable or transmitter-enable controls. Its low-power BiCMOS design is intended for industrial and commercial equipment where low-power differential interfaces, compact PCB area, and controlled transition behavior are important.

An RS-485/RS-422 transceiver is an interface IC that converts logic-level signals into balanced differential signals and reconstructs digital data from a differential receiver input. This device supports both RS-485 and RS-422 applications, covering point-to-multipoint bus communications and point-to-point links. Within the interface hierarchy, it belongs to the RS-485 transceiver category, uses differential signaling, and operates as a physical-layer communications component.

The principal operating characteristics are a 5 V supply, a 250 kbps maximum signaling rate, full-duplex operation, and one integrated transceiver in an 8-SOIC package. The Intersil datasheet describes the ISL8488 family as a low-power, high-speed or slew-rate-limited RS-485/RS-422 device. Its balanced interface is suited to industrial networking, instrumentation, and control links where cable-length and ground-offset considerations make differential signaling preferable to single-ended logic.

The BiCMOS architecture combines bipolar and CMOS process characteristics, supporting low-power operation while providing the drive and receive performance required by balanced communication links. The device accepts a 10% supply-tolerance range of 4.5 V to 5.5 V. Because the ISL8488IB-T has no receiver-enable or transmitter-enable pins, its operating state is managed entirely through the bus and data-path behavior rather than local logic-control inputs.

Typical uses include industrial RS-485 controllers, factory automation equipment, building-control interfaces, instrumentation, and point-to-point RS-422 links. In these systems, the transceiver provides the physical-layer connection between a host UART or communications controller and a balanced cable. The 250 kbps ceiling makes it appropriate for moderate-speed control and monitoring traffic rather than high-speed video or storage networks.

Layout should preserve the integrity of the differential pair and provide a controlled return path. Keep the two bus conductors closely coupled, route them away from high-current switching paths, and use the application guidance in the Intersil datasheet for termination and protection. Confirm the selected connector, cable, and grounding strategy satisfy the required RS-485 or RS-422 system configuration.

This page consolidates the device identity, operating limits, package details, family alternatives, and implementation guidance into an engineering-focused resource. It also distinguishes verified operating facts from parameters that require confirmation against the manufacturer datasheet before production release.

بدائل مباشرة لـ ISL8488IB-T — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع ISL8488IB-T (نفس عامل الشكل والبصمة) — يختلف في Package, Mounting Type, Transceiver Configuration.

Renesas Electronics
Package: 8-pin SOIC
Transceiver Configuration: 1 driver / 1 receiver
قارن مع ISL8488IB-T →
Renesas Electronics
Package: 8-pin plastic DIP (8-PDIP)
Mounting Type: Through-hole
قارن مع ISL8488IB-T →

ISL8488IP

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
Renesas Electronics
📦 8-SOIC
RS-485/RS-422 transceiver · 5 V · 250 kbps · Full duplex · RS-485 and RS-422 · 1/1 transceiver · Slew-rate limited · Low power

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ISL8488IBZ

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
Renesas Electronics
📦 8-SOIC
5 V · 4.5 V to 5.5 V · 10% · RS-485 and RS-422 · 1 driver / 1 receiver · Full duplex · BiCMOS · Low power

تواصل لمعرفة السعر

عرض ورقة البيانات ←

ISL8488EIBZA-T

✅ بديل مباشر
📦 8-SOIC
Adds driver-output and receiver-input protection specified at ±15 kV ESD while retaining the 5 V ISL8488 family interface

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8489EIBZA-T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-SOIC
Same Renesas 5 V BiCMOS RS-485/RS-422 family in 8-SOIC with ESD protection; ISL8489E data-rate target differs from the 250 kbps ISL8488IB-T

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8490EIBZA-T

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-SOIC
Same Renesas 5 V BiCMOS RS-485/RS-422 family in 8-SOIC with ESD protection; ISL8490E speed or power target differs from the 250 kbps ISL8488IB-T

📋 بديل مرجعي (غير موجود في الكتالوج)

ISL8488IB-T المواصفات

Product Type RS-485/RS-422 transceiver
Manufacturer Renesas Electronics
Transceiver Configuration 1 transmitter and 1 receiver
Operating Mode Full duplex
Maximum Data Rate 250 kbps
Nominal Supply Voltage 5 V
Operating Supply Voltage Range 4.5 V to 5.5 V
Supply Tolerance 10%
Process Technology BiCMOS
Supported Standards RS-485 and RS-422
Signal Type Balanced differential
Transmitter Enable None
Receiver Enable None
Transition Control Slew-rate-limited option
العلبة 8-SOIC
نوع التركيب Surface mount
عدد الأطراف 8 pins

دليل تكوين أطراف ISL8488IB-T 8-soic

تكوين الأطراف لـ ISL8488IB-T (حزمة 8-soic). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 8-soic لـ ISL8488IB-T

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISL8488IB-T.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

ISL8488IB-T مناسب لـ 6 التطبيقs: Industrial RS-485 Control Links, Point-to-Point RS-422 Data Links, Factory Automation Instrumentation, Building Control and HVAC Networks, Test and Measurement Equipment, Security and Access-Control Terminals.

🏭

Industrial RS-485 Control Links

The ISL8488IB-T is suitable for full-duplex RS-485 links in industrial controllers because it combines a 5 V operating range of 4.5 V to 5.5 V with differential signaling up to 250 kbps. Place the transceiver between a host UART and a balanced cable to provide physical-layer drive and receive functions. Its one-transmitter, one-receiver configuration supports simultaneous communication in point-to-point or appropriately terminated topologies. The principal design consideration is confirming that the system architecture does not require transmit or receive enable controls, because this device provides neither.

🌐

Point-to-Point RS-422 Data Links

The ISL8488IB-T can serve as the line interface for point-to-point RS-422 equipment requiring full-duplex differential communication. Its 250 kbps maximum data rate is appropriate for supervisory commands, status reporting, and configuration traffic rather than bulk data transfer. The 8-SOIC package limits PCB footprint, while the absence of local enable pins simplifies control routing. Engineers should preserve the conductor spacing of the differential pair, provide the interface components recommended by the datasheet, and verify cable length and termination against the selected baud rate.

🏭

Factory Automation Instrumentation

The ISL8488IB-T fits factory instrumentation that exchanges moderate-speed control data over industrial cabling. Its BiCMOS implementation, 5 V supply range of 4.5 V to 5.5 V, and differential RS-485 or RS-422 interface support robust communication between a controller and remote sensing or actuator modules. The 250 kbps ceiling is well suited to supervisory traffic. Because the device does not include transmit or receive enable inputs, system designers should define the bus topology and operating states so that the always-active interface behaves as intended.

🧩

Building Control and HVAC Networks

The ISL8488IB-T can interface building-control equipment using a 5 V RS-485 or RS-422 balanced link. Its full-duplex arrangement is useful for equipment that exchanges commands and status through separate differential paths, while the 250 kbps rate comfortably covers environmental monitoring and supervisory control traffic. The 8-SOIC package supports compact controller boards. A production design should confirm operating-temperature requirements, cable grounding, transient protection, and whether the enhanced ±15 kV ESD protection of the ISL8488EIBZA-T is preferable at an exposed connector.

🖥️

Test and Measurement Equipment

The ISL8488IB-T is appropriate for test and measurement instruments that need a compact, balanced command or measurement link. A 250 kbps RS-422 connection can carry instrument status, configuration commands, and sampled low-rate telemetry while rejecting the common-mode disturbance associated with single-ended signaling. Its 5 V BiCMOS architecture operates from 4.5 V to 5.5 V, and the 8-SOIC package reduces board-area requirements. The design must verify protocol timing, isolation needs, grounding, and cable termination against the instrument's accuracy and safety requirements.

🎥

Security and Access-Control Terminals

The ISL8488IB-T can connect access-control terminals, readers, and door controllers over a short industrial balanced network. The 250 kbps rate supports credential events, status reports, and administrative commands without requiring a high-speed serial standard. Full-duplex operation simplifies implementations that need predictable command and response behavior, while the 8-SOIC package supports compact terminal electronics. Engineers should assess cable exposure, ESD exposure, operating temperature, and whether the ISL8488EIBZA-T's specified ±15 kV ESD protection is needed at externally accessible connectors.

What is the operating voltage of ISL8488IB-T?
The ISL8488IB-T operates from 4.5 V to 5.5 V, with a nominal supply voltage of 5 V. According to the Intersil datasheet description, the device is specified for a 10% supply-tolerance range, making it appropriate for conventional 5 V communication equipment. Confirm that the supply remains within tolerance during startup, transients, and cable-connected operation.
What is the maximum data rate of ISL8488IB-T?
The ISL8488IB-T supports signaling rates up to 250 kbps. The Intersil datasheet identifies it as a 5 V, low-power, high-speed or slew-rate-limited RS-485/RS-422 transceiver. This rate is suitable for industrial control, instrumentation, and monitoring links where reliable balanced signaling is more important than very high data throughput.
Where can I download the ISL8488IB-T datasheet PDF?
The ISL8488IB-T datasheet is available through the linked datasheet record, while the Renesas product family information is published under the ISL8488E family page. The 8-SOIC device description identifies 5 V operation, RS-485/RS-422 support, full-duplex communication, and a maximum rate of 250 kbps. Use the pin-description and electrical-characteristics tables in the manufacturer datasheet when laying out and qualifying the PCB.
Where is the pinout for ISL8488IB-T?
The ISL8488IB-T uses an 8-SOIC package, but the individual terminal assignments are not reproduced on this page. Use the pin-description table in the Intersil datasheet before assigning PCB tracks. In particular, verify the differential driver outputs, receiver inputs, supply terminals, and ground connections rather than inferring their locations from a generic transceiver outline.
Does ISL8488IB-T support full-duplex RS-485 communication?
Yes, the ISL8488IB-T is a one-transmitter, one-receiver full-duplex RS-485/RS-422 transceiver. Its separate differential driver and receiver paths permit simultaneous transmission and reception in a point-to-point topology. This differs from common half-duplex transceivers that share a single bus and require an external direction-control arrangement.
Does ISL8488IB-T have transmit and receive enable pins?
No, the ISL8488IB-T has no transmitter-enable or receiver-enable inputs. The device description identifies it as a full-duplex transceiver with no separate transmit or receive enable controls. System designers should therefore account for its always-active interface architecture and verify signal behavior at the connected controller and bus nodes.
ISL8488IB-T vs ISL8488EIBZA-T: which is better for an industrial RS-485 link?
The ISL8488EIBZA-T is the better choice when the design requires the enhanced family member's ±15 kV ESD-protected driver outputs and receiver inputs. The ISL8488IB-T remains suitable for 5 V RS-485/RS-422 links without that enhanced protection specification. Both are associated with 8-SOIC-style packages, but their exact terminal functions and qualification requirements should be checked before substitution.
When should I choose ISL8488IB-T over ISL8488EIBZA-T?
Choose ISL8488IB-T when the interface is a conventional 5 V full-duplex RS-485 or RS-422 link and the enhanced ESD specification of the ISL8488EIBZA-T is not required. Choose the E-series device when exposed connectors make ±15 kV ESD protection a defined system requirement. The final decision must also consider package markings, operating-temperature grade, and lifecycle requirements.
Is ISL8488IB-T suitable for industrial automation equipment?
The ISL8488IB-T is suitable for many industrial automation and control links because it provides a 5 V supply range of 4.5 V to 5.5 V, differential RS-485/RS-422 signaling, and operation up to 250 kbps. Its full-duplex architecture is useful for point-to-point communications. Industrial qualification, temperature limits, surge protection, and isolation requirements should be checked separately for the finished equipment.
What can replace ISL8488IB-T?
The closest documented family alternatives are the Renesas ISL8488IP, ISL8488IBZ, ISL8488EIBZA-T, ISL8489EIBZA-T, and ISL8490EIBZA-T, but each must be qualified against the required package, pinout, data rate, enable architecture, and ESD rating. The ISL8488EIBZA-T adds a specified ±15 kV ESD protection feature, so it is not functionally identical in every protection respect.
What is the best Renesas equivalent for ISL8488IB-T?
The best Renesas starting point is the part in the same ISL8488 family that preserves the 8-SOIC footprint, 5 V operation, full-duplex architecture, and required data rate. ISL8488EIBZA-T provides enhanced ESD protection, while the ISL8489E and ISL8490E family members may serve different speed or power requirements. Confirm the exact pinout and timing characteristics against the Intersil datasheet before production use.
Where can I buy ISL8488IB-T online?
Use the Request a Quote form on this page to request ISL8488IB-T pricing, stock confirmation, and lead time. The request should include the exact ISL8488IB-T orderable MPN and the required reel quantity. This avoids selecting a different temperature grade, package suffix, or non-tape-and-reel ordering code by mistake.
What is the price of ISL8488IB-T?
Current pricing for ISL8488IB-T is handled through the Request a Quote form on this page. Submit the exact MPN, target quantity, and shipment destination to obtain a current quotation. Quote requests are also the appropriate route for confirming reel availability, lead time, and any scheduled volume pricing.
What is the lead time and stock status for ISL8488IB-T?
Current stock and lead time for ISL8488IB-T should be confirmed through the Request a Quote form on this page. Include the required quantity and whether reels or cut tape are acceptable. Distributor status can change independently of the component's lifecycle, so a quotation confirmation is more reliable than treating a general catalog page as a stock guarantee.
What are the key specifications of ISL8488IB-T that engineers should know?
The ISL8488IB-T is a 5 V, full-duplex RS-485/RS-422 transceiver with one transmitter and one receiver, operation up to 250 kbps, and an 8-SOIC package. According to the Intersil datasheet description, it is a low-power BiCMOS device intended for high-speed or slew-rate-limited balanced communication. Its operating supply range is 4.5 V to 5.5 V, and it has no transmit or receive enable pins.
Is ISL8488IB-T RoHS and REACH compliant?
The RoHS and REACH status must be confirmed from the current Renesas material-declaration record for the exact ISL8488IB-T orderable MPN. Do not infer compliance solely from the 8-SOIC package or from another member of the ISL8488 family. Request the applicable declaration or material-compliance record before incorporating the part into a regulated production BOM.

بيانات مرجعية هندسية لـ ISL8488IB-T — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the ISL8488IB-T for a 5 V, full-duplex RS-485 or RS-422 link that operates at or below 250 kbps and does not require separate transmit or receive enable controls. Choose the ISL8488EIBZA-T when the interface needs the documented ±15 kV ESD protection, particularly when a cable or connector is externally accessible. Consider the ISL8489EIBZA-T or ISL8490EIBZA-T only when their different speed or power characteristics better match the link, after checking the exact pinout and electrical limits. The ISL8488IP and ISL8488IBZ are same-family candidates for ordering or temperature-grade review, but their order codes must be checked carefully. In every case, validate the terminal assignments, cable topology, termination, operating temperature, and production lifecycle requirements before approving a replacement.

المقارنة مع البدائل

المعامل هذا المنتج ISL8488IP ISL8488IBZ ISL8488EIBZA-T ISL8489EIBZA-T ISL8490EIBZA-T
Brand Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics Renesas Electronics
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver ESD-protected RS-485/RS-422 transceiver RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Nominal Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Process Technology BiCMOS BiCMOS BiCMOS BiCMOS BiCMOS BiCMOS

أبرز الفروقات

  • Fixed 250 kbps operating target (مقابلISL8489EIBZA-T)
  • ESD-protected family option for exposed interfaces (مقابلISL8488IB-T)
  • Compact eight-pin differential interface (مقابلISL8488IBZ)

ملاحظات التصميم

Route the RS-485 or RS-422 differential pair as a tightly coupled pair with continuous reference beneath it on a multilayer PCB. Keep the pair away from switching nodes, motor windings, high-current return paths, and antenna-like structures. Match the differential pair length and impedance according to the edge rate and cable topology, then use the pin and application diagrams in the Intersil datasheet when placing protection and termination components.

Provide a stable 5 V rail that remains between 4.5 V and 5.5 V under load and transient conditions. Place the recommended supply-bypass capacitor adjacent to the device's supply and ground terminals, with a short and low-impedance return path. Confirm the logic-high and logic-low levels at the connected controller because the bus interface and digital input thresholds must be compatible with the host supply voltage.

Do not treat the 8-SOIC outline as a complete pinout definition; several related family members have different data rates, protection levels, and ordering codes. Before substituting any listed alternative, compare the numbered terminal assignments, receiver and driver enable arrangement, supply tolerance, data-rate limit, temperature grade, and ESD specification. A package match alone does not establish production equivalence.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The device is an industrial communications interface IC, but no specific AEC-Q100, RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified. Confirm current material-compliance documentation for the exact orderable MPN.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

ISL8488IB-T datasheet ISL8488IB-T pinout ISL8488IB-T datasheet pdf ISL8488IB-T equivalent ISL8488IB-T replacement ISL8488IB-T cross reference ISL8488IB-T vs ISL8488EIBZA-T ISL8488IB-T 250kbps RS-485 ISL8488IB-T 8-SOIC footprint Renesas ISL8488IB-T ISL8488IB-T price ISL8488IB-T stock ISL8488IB-T industrial control ISL8488IB-T RS-422 application circuit

المكونات والمصطلحات ذات الصلة

Renesas Electronics ISL8488IB-T ISL8488IP ISL8488IBZ ISL8488EIBZA-T ISL8489EIBZA-T ISL8490EIBZA-T RS-485 transceiver RS-422 transceiver full-duplex transceiver differential signaling interface IC BiCMOS 8-SOIC SOIC package surface-mount package industrial automation factory instrumentation building control test and measurement 250 kbps 5 V supply slew-rate-limited ESD protection balanced communication
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر