ISO6763 - 6-Ch Reinforced Digital Isolator 50Mbps | Texas Instruments
MPN: ISO6763 ✓ نشطISO6763 نظرة عامة
A digital isolator is an interface IC that transfers digital signals across a galvanic isolation barrier while blocking high voltages, isolating ground potentials, and preventing noise coupling. Within the signal-chain hierarchy, digital isolators belong to the interface IC family and are essential building blocks in industrial data buses, isolated power supplies, and motor-drive gate-drive isolation systems.
Key features include six isolation channels in a 3/3 configuration, 50 Mbps signaling for high-speed SPI and parallel interfaces, and reinforced 5000 Vrms isolation rating for safety-critical designs. The ISO6763 belongs to the ISO676x family (ISO6760, ISO6761, ISO6762, ISO6763, datasheet SLLSFK0E, August 2021, revised February 2023), which shares silicon-on-insulator-based capacitive isolation technology with the proven ISO77xx generation.
The device uses TI's latest generation of capacitive isolation architecture with on-chip transformers implemented as SiO2 capacitors, delivering robust EMC performance with high CMTI. Low propagation delay and low channel-to-channel skew make it well suited for clocked interfaces. Wide-side supply support down to 1.8 V allows direct interfacing with modern low-voltage MCUs and FPGAs without level shifting.
Typical applications include RS-485 and CAN bus isolation, isolated SPI for ADCs and DACs, industrial PLC I/O modules, and motor-control signal isolation connecting MCUs to gate drivers. The automotive-grade ISO6763FQDWRQ1 variant extends usage to vehicle systems requiring AEC-Q100 qualification.
When designing, place 0.1 uF bypass capacitors close to both VCC1 and VCC2 pins and route signals across the barrier with generous creepage clearance; unused inputs should be tied to a defined logic level to prevent floating-channel oscillation.
بدائل مباشرة لـ ISO6763 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع ISO6763 (نفس عامل الشكل والبصمة) — يختلف في Package, CMTI, Maximum Data Rate, Common-Mode Transient Immunity, Number of Channels.
ISO6763FQDWRQ1
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ISO7763DWR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←ISO6762DWR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
ISO6760DWR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←SI8663BB-B-IS
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
ADuM261N1BRZ
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
ISO6763 المواصفات
| Number of Channels | 6 (3/3 direction) |
| Max Data Rate | 50 Mbps |
| Isolation Rating | 5000 Vrms |
| CMTI | 50 kV/us |
| Supply Voltage Range (Side 1) | 1.8 V to 5.5 V |
| Supply Voltage Range (Side 2) | 1.8 V to 5.5 V |
| Logic Level Support | 1.8 V, 2.5 V, 3.3 V, 5 V |
| Isolation Technology | Capacitive (SiO2, SOI-based) |
| Supported Interfaces | CAN, RS232, RS485, SPI |
| العلبة | 16-SOIC (DW, 7.50 mm width) |
| نوع التركيب | Surface Mount |
| Automotive Grade Variant | ISO6763FQDWRQ1 (AEC-Q100) |
| حالة RoHS | Compliant |
| Family Datasheet | SLLSFK0E (Aug 2021, rev Feb 2023) |
دليل تكوين أطراف ISO6763 16-soic (dw, 7.50 mm width)
تكوين الأطراف لـ ISO6763 (حزمة 16-soic (dw, 7.50 mm width)). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ ISO6763.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
ISO6763 مناسب لـ 6 التطبيقs: Isolated RS-485 Bus Nodes, CAN Bus Isolation, Isolated SPI for ADCs and DACs, Motor Drive Gate-Drive Signal Isolation, PLC I/O Modules, Automotive Body and Powertrain Isolation.
Isolated RS-485 Bus Nodes
The ISO6763 isolates the UART/control lines feeding RS-485 transceivers in industrial fieldbus nodes. Its 50 Mbps rate comfortably exceeds 20 Mbps profiling needs, and 50 kV/us CMTI sustains signaling through large ground-potential transients common on long factory floors. Six channels in 3/3 direction allow full TX/RX plus direction-control and fault signaling across one device, replacing multiple dual-channel isolators and cutting BOM count and board area.
موصى به
CAN Bus Isolation
For isolated CAN and CAN FD nodes, the ISO6763 isolates TX, RX, and standby/control signals between the MCU and CAN transceiver. Its 5000 Vrms reinforced isolation supports safety separation in industrial and automotive gateways, while 50 kV/us CMTI keeps the bus stable under load-dump and ground-shift events. The 1.8 V logic support lets it sit directly beside modern low-voltage MCUs without level translators.
موصى به
Isolated SPI for ADCs and DACs
The ISO6763's 50 Mbps data rate supports high-throughput isolated SPI links to precision data converters. Three channels in each direction carry SCLK, MOSI/CS and MISO/DRDY signals with low channel-to-channel skew across the barrier. 1.8 V to 5 V supply support on both sides allows direct connection to low-voltage converters and 5 V industrial logic. The capacitive isolation adds no switching noise into sensitive analog domains.
موصى به
Motor Drive Gate-Drive Signal Isolation
In motor inverters, the ISO6763 isolates PWM and fault/enable signals between the MCU controller domain and IGBT/SiC gate-driver domain. The 50 kV/us CMTI is essential where high dv/dt switching edges would corrupt ordinary optocouplers, and 5000 Vrms reinforced rating supports the safety separation between low-voltage control and high-voltage power stages. Low propagation delay preserves PWM dead-time accuracy for efficient switching.
موصى به
PLC I/O Modules
Programmable logic controller I/O cards use the ISO6763 to isolate digital input/output banks from the backplane logic. Six channels per device consolidate isolation for dense I/O boards, reducing component count versus dual-channel parts. Reinforced 5000 Vrms isolation addresses field-wiring surge exposure, and robust EMC performance helps meet industrial immunity requirements in electrically noisy cabinets.
موصى به
Automotive Body and Powertrain Isolation
For vehicle ECUs linking 3.3 V/5 V domains across battery-domain boundaries, the AEC-Q100 qualified ISO6763FQDWRQ1 variant provides identical 3/3-channel, 50 Mbps, 5000 Vrms isolation with automotive qualification. It suits onboard charger communication, isolated sensor interfaces, and domain gateway links. The shared package with the standard ISO6763 lets one PCB layout serve both industrial and automotive end items.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ ISO6763 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | ISO6763FQDWRQ1 | ISO7763DWR | SI8663BB-B-IS | ADuM261N1BRZ |
|---|---|---|---|---|---|
| Package | 16-SOIC (DW, 7.50 mm) | 16-SOIC (DW) - same | 16-SOIC (DW) - same | 16-SOIC - same footprint class | 16-SOIC - same footprint class |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Skyworks Solutions | Analog Devices |
| Channels | 6 (3/3) | 6 (3/3) | 6 (3/3) | 6 (3/3) | 6 (3/3) |
| Automotive Grade | No (standard ISO6763) | Yes (AEC-Q100) | Q1 option available | No | No |
أبرز الفروقات
- Latest-generation reinforced EMC isolator (مقابلISO7763DWR)
- Direct automotive path with same footprint (مقابلISO6763FQDWRQ1)
- 1.8 V logic support on both sides (مقابلADuM261N1BRZ)
ملاحظات التصميم
Place 0.1 uF ceramic bypass capacitors within 2 mm of both VCC1 and VCC2 pins, each referenced to its own side ground. Maintain the isolation barrier as a continuous board slot or gap; route all six signals perpendicular to the barrier to preserve creepage and minimize inter-channel coupling across the isolation boundary.
Tie unused channel inputs to a defined logic level (VCC or GND of that side). Floating inputs on capacitive isolators can oscillate and inject noise into adjacent channels. Also confirm default output states on power-up: if the other side is unpowered, outputs default low, which matters for fail-safe behavior in RS-485 direction control and gate-drive enable lines.
At 50 Mbps, use series termination (22 to 33 ohm) on high-speed channels near the driving side to control ringing, and keep traces on each side short with solid ground references. The isolator's low channel-to-channel skew suits clocked SPI; minimize asymmetric trace lengths between clock and data lines to preserve setup/hold margins at the receiver.
معلومات الامتثال
RoHS compliant per DigiKey listing for ISO6763DWR. AEC-Q100 qualification applies only to ISO6763FQDWRQ1 variant. Detailed REACH/halogen status: see TI quality portal.
