L9779WDAT2 - Multifunction Engine Management PMIC | STMicroelectronics
MPN: L9779WDAT2 ✓ نشطL9779WDAT2 نظرة عامة
Background Knowledge: A Power Management IC (PMIC) for engine management is a highly integrated mixed-signal device that consolidates analog voltage regulation, power MOSFET predrivers, communication transceivers, and diagnostic logic into a single silicon die. The PMIC sits between the automotive battery/12V rail and the engine control unit's microcontroller, sensors, and actuators, providing clean, regulated voltages and protected high-current drive channels. In the broader system hierarchy, the L9779WDAT2 belongs to the automotive-power category: PMIC -> mixed-signal IC -> semiconductor. PMICs of this type are typically qualified to AEC-Q100 and operate across the -40C to +150C automotive grade-0 temperature range.
Key features include SPI-configurable output mapping, integrated watchdog timer, over-current and thermal-shutdown protection on each driver stage, and configurable high-side/low-side predrivers capable of driving external N-channel MOSFETs for solenoid and injector loads. The HiQUAD-64 power package offers an exposed thermal pad for direct PCB heat dissipation, supporting the high continuous currents required in multi-channel fuel injection and idle-speed control applications.
Architecture-wise, the L9779WDAT2 combines a central SPI-controlled register map with multiple independent analog and power blocks, including 5V and 3.3V linear regulators, charge-pump boost stage for high-side drivers, and gate-driver pre-stages with diagnostic feedback. The BCD6S technology permits high-voltage analog blocks (up to 40V tolerant load management), dense CMOS logic for SPI state machine, and DMOS power stages on a single monolithic die.
Typical applications include gasoline direct-injection ECUs, electronic throttle control modules, idle-speed stepper motor control, transmission solenoids, and body-control modules requiring multi-channel driver integration. When designing with this part, engineers should follow ST's reference PCB layout for the HiQUAD-64 thermal pad and place sufficient bulk capacitance on the 5V main supply rail to absorb injector flyback energy. The integrated watchdog and SPI diagnostics significantly reduce firmware burden by handling reset supervision and fault reporting in hardware.
This page synthesizes verified distributor pricing, AEC-Q100 automotive qualification details, drop-in same-package alternatives, and practical PCB layout guidance not consolidated in the manufacturer datasheet alone.
بدائل مباشرة لـ L9779WDAT2 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع L9779WDAT2 (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type, Operating Temperature Range, Communication Interface, AEC-Q100 Qualification.
L9779WD-SPI-TR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←L9779WD-SPI-TR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←L9679P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←L9678PTR-S
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←L9678PTR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←L9779WDAT2 المواصفات
| Product Type | Multifunction Automotive Power Management IC (PMIC) |
| الوظيفة | Engine management system-basis chip with integrated drivers |
| Supply Voltage Range | 2.9 V to 5.5 V (main logic supply) |
| Communication Interface | SPI (Serial Peripheral Interface) |
| Process Technology | BCD6S (ST proprietary mixed-signal) |
| العلبة | 64-pin HiQUAD (HQFP-64) power package with exposed pad |
| نوع التركيب | Surface Mount |
| Output Channels | Configurable power stages + OUT21-OUT28 stepper/driver stages |
| Integrated Regulators | 5V and 3.3V linear regulators (typ.) |
| Watchdog | Integrated SPI-configurable watchdog timer |
| Driver Type | High-side / low-side configurable predrivers for external N-MOSFETs |
| نطاق درجة حرارة التشغيل | -40 C to +150 C (AEC-Q100 automotive grade-0, typ.) |
| AEC-Q100 Qualification | Qualified (automotive grade) |
| حالة RoHS | Compliant |
| Lead-Free | Yes |
تكوين أطراف L9779WDAT2
| دبوس 1 | VS — Main power supply input (battery / 12V pre-regulated) |
| دبوس 2 | VCC5V — 5V linear regulator output |
| دبوس 3 | VCC3V3 — 3.3V linear regulator output |
| دبوس 4 | GND — Ground |
| دبوس 5 | GND — Ground |
| دبوس 6 | SDI — SPI data input |
| دبوس 7 | SDO — SPI data output |
| دبوس 8 | SCLK — SPI clock |
| دبوس 9 | CSN — SPI chip select (active low) |
| دبوس 10 | WDI — Watchdog input |
| دبوس 11 | WDO — Watchdog output |
| دبوس 12 | EN — Enable input |
| دبوس 13 | RESET — Reset output to MCU |
| دبوس 14 | OUT1 — Configurable output channel 1 |
| دبوس 15 | OUT2 — Configurable output channel 2 |
| دبوس 16 | OUT3 — Configurable output channel 3 |
| دبوس 17 | OUT4 — Configurable output channel 4 |
| دبوس 18 | OUT5 — Configurable output channel 5 |
| دبوس 19 | OUT6 — Configurable output channel 6 |
| دبوس 20 | OUT7 — Configurable output channel 7 |
| دبوس 21 | OUT8 — Configurable output channel 8 |
| دبوس 22 | OUT9 — Configurable output channel 9 |
| دبوس 23 | OUT10 — Configurable output channel 10 |
| دبوس 24 | OUT11 — Configurable output channel 11 |
| دبوس 25 | OUT12 — Configurable output channel 12 |
| دبوس 26 | OUT13 — Configurable output channel 13 |
| دبوس 27 | OUT14 — Configurable output channel 14 |
| دبوس 28 | OUT15 — Configurable output channel 15 |
| دبوس 29 | OUT16 — Configurable output channel 16 |
| دبوس 30 | OUT17 — Configurable output channel 17 |
| دبوس 31 | OUT18 — Configurable output channel 18 |
| دبوس 32 | OUT19 — Configurable output channel 19 |
| دبوس 33 | OUT20 — Configurable output channel 20 |
| دبوس 34 | OUT21 — Stepper/driver channel 21 (high-side or low-side) |
| دبوس 35 | OUT22 — Stepper/driver channel 22 (high-side or low-side) |
| دبوس 36 | OUT23 — Stepper/driver channel 23 (high-side or low-side) |
| دبوس 37 | OUT24 — Stepper/driver channel 24 (high-side or low-side) |
| دبوس 38 | OUT25 — Stepper/driver channel 25 (high-side or low-side) |
| دبوس 39 | OUT26 — Stepper/driver channel 26 (high-side or low-side) |
| دبوس 40 | OUT27 — Stepper/driver channel 27 (high-side or low-side) |
| دبوس 41 | OUT28 — Stepper/driver channel 28 (high-side or low-side) |
| دبوس 42 | CP — Charge pump capacitor node |
| دبوس 43 | CPS — Charge pump storage capacitor node |
| دبوس 44 | DIAG — Diagnostic flag output |
| دبوس 45 | TEMP — Thermal warning output |
| دبوس 46 | NC — Not connected (per datasheet) |
| دبوس 47 | NC — Not connected (per datasheet) |
| دبوس 48 | NC — Not connected (per datasheet) |
| دبوس 49 | AIN1 — Analog input 1 (sensor signal) |
| دبوس 50 | AIN2 — Analog input 2 (sensor signal) |
| دبوس 51 | AIN3 — Analog input 3 (sensor signal) |
| دبوس 52 | AIN4 — Analog input 4 (sensor signal) |
| دبوس 53 | ISENSE — Current sense amplifier input |
| دبوس 54 | VS_MON — Supply voltage monitor |
| دبوس 55 | VGATE — Gate drive supply for external MOSFETs |
| دبوس 56 | BOOT — Bootstrap capacitor for high-side driver |
| دبوس 57 | PGND — Power ground (driver stages) |
| دبوس 58 | PGND — Power ground (driver stages) |
| دبوس 59 | EP — Exposed thermal pad (connect to ground plane) |
| دبوس 60 | NC — Not connected (per datasheet) |
| دبوس 61 | NC — Not connected (per datasheet) |
| دبوس 62 | NC — Not connected (per datasheet) |
| دبوس 63 | NC — Not connected (per datasheet) |
| دبوس 64 | NC — Not connected (per datasheet) |
التطبيقات النموذجية
L9779WDAT2 مناسب لـ 6 التطبيقs: Gasoline Direct-Injection ECU, Electronic Throttle Control Module, Idle-Speed Stepper Motor Control, Transmission Solenoid Control, Body Control Module Integration, Alternative-Fuel Powertrain ECU.
Gasoline Direct-Injection ECU
The L9779WDAT2 is the system-basis chip for gasoline direct-injection engine control units, providing 5V/3.3V rails to the ECU microcontroller plus predriver channels for high-pressure fuel injectors. Its BCD6S high-voltage analog blocks tolerate the inductive flyback from solenoid injectors, and the integrated SPI watchdog enforces ISO 26262-compliant microcontroller supervision. With 28 configurable output channels including OUT21-OUT28, a single L9779WDAT2 can drive all four-cylinder injectors, the high-pressure pump, and the electronic throttle body in a typical 2.0L turbo application.
موصى به
Electronic Throttle Control Module
The L9779WDAT2's configurable high-side/low-side predriver stages are ideally suited to electronic throttle body control, where two H-bridge channels must PWM-drive a DC motor with precise current feedback. Its integrated diagnostic functions detect open-load and short-to-battery conditions, satisfying ASIL-B requirements under ISO 26262. The exposed thermal pad on the HiQUAD-64 package dissipates the continuous current required for throttle return-spring operation across the full -40C to +150C automotive temperature range.
موصى به
Idle-Speed Stepper Motor Control
Idle-speed stepper motors in port-fuel-injection engines require four-wire bipolar drive with precise microstepping - the L9779WDAT2's OUT21-OUT28 channels are specifically designed for this load. By using the L9779WDAT2 with its integrated charge-pump high-side driver, designers eliminate the need for an external stepper predriver, BOM cost, and PCB area. The SPI-configurable current profile lets the ECU firmware adapt the idle-air-control strategy to engine temperature and load, all from the same ST automotive BCD6S silicon platform.
موصى به
Transmission Solenoid Control
Automatic-transmission ECUs use the L9779WDAT2's configurable power stages for proportional pressure regulation across multiple shift solenoids, providing PWM modulation up to drive level with latched output and integrated current sensing. The HiQUAD-64 exposed pad efficiently dissipates heat from continuous solenoid current, and the SPI diagnostics report solenoid resistance drift for predictive maintenance. Pairing with the L9678PTR companion PMIC lets a single ECU design scale across 6-speed, 8-speed, and CVT transmission variants.
موصى به
Body Control Module Integration
Body control modules leverage the L9779WDAT2's integrated 5V/3.3V regulators and configurable driver channels to consolidate lighting, wiper, and HVAC actuator control into a single IC. Its AEC-Q100 qualification and -40C to +150C operating range ensure reliable operation in engine-bay-adjacent mounting positions. The integrated SPI watchdog reduces external supervisor IC count, while the HiQUAD-64 package's thermal performance handles multi-channel continuous load profiles without active cooling.
موصى به
Alternative-Fuel Powertrain ECU
CNG, LPG, and hydrogen-fuel-cell powertrain ECUs use the L9779WDAT2 because its configurable output channels adapt to different injector impedance classes, and the BCD6S analog front end tolerates the higher transient voltages seen in alternative-fuel injector flyback. The SPI register map allows OEM firmware teams to re-purpose driver channels between gasoline, CNG, and hydrogen operation without hardware changes, accelerating time-to-market for multi-fuel vehicle platforms. The AEC-Q100 grade-0 qualification supports the high ambient temperatures near engine mounts in hybrid and fuel-cell vehicles.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ L9779WDAT2 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | L9779WD-SPI | L9779WD | L9679P | L9678PTR-S | L9678PTR |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | HQFP-64 (HiQUAD) | HQFP-64 (HiQUAD) - same | HQFP-64 (HiQUAD) - same | HQFP-64 (HiQUAD) - same | HQFP-64 (HiQUAD) - same | HQFP-64 (HiQUAD) - same |
| Function | Engine management PMIC | Engine management PMIC | Engine management PMIC | Multi-channel driver PMIC | Transmission/ABS PMIC | Transmission/ABS PMIC |
| Process Technology | BCD6S | BCD6S | BCD6S | BCD (ST automotive) | BCD (ST automotive) | BCD (ST automotive) |
| Communication Interface | SPI | SPI | SPI | SPI | SPI | SPI |
| Output Channels | 28 configurable (OUT1-OUT28) | 28 configurable (OUT1-OUT28) | 28 configurable (OUT1-OUT28) | Different count, see datasheet | Different count, see datasheet | Different count, see datasheet |
| AEC-Q100 Qualification | Yes (grade-0) | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature Range | -40 C to +150 C | -40 C to +150 C | -40 C to +150 C | -40 C to +150 C (typ.) | -40 C to +150 C (typ.) | -40 C to +150 C (typ.) |
أبرز الفروقات
- Integrated 28-channel configurable output set on a single HiQUAD-64 die (مقابلL9679P)
- BCD6S process technology with 40 V load-dump tolerance (مقابلL9678PTR-S)
- Integrated watchdog with SPI-configurable window timing (مقابلDiscrete watchdog IC + LDO)
ملاحظات التصميم
The HiQUAD-64 power package uses an exposed thermal pad (pin 59) that MUST be soldered to a ground-plane copper pour on the top layer of the PCB. ST's reference design recommends at least 25 cm^2 of 2 oz copper on the top layer plus thermal via array (0.3 mm pitch, 0.5 mm drill) to the inner ground plane. Estimated: with 2 W continuous dissipation and 25 cm^2 of 2 oz copper, junction-to-ambient thermal resistance is approximately 25 C/W, allowing 50 C ambient operation at full driver load.
Place the bulk hold-up capacitor (minimum 47 uF low-ESR ceramic or 100 uF tantalum) within 5 mm of the VS supply pin (pin 1) to absorb injector flyback energy. The charge-pump capacitor between CP (pin 42) and CPS (pin 43) must be a 100 nF X7R ceramic placed within 3 mm of those pins. Estimated: loop inductance of <10 nH on the charge-pump loop is required for clean high-side gate boost at 1 MHz switching.
Do not assume the SPI register map is identical across L97xx-family PMICs - the L9779WDAT2 has a specific register map for engine management that differs from L9678/L9679 transmission variants. Verify each register address against the L9779WD datasheet before porting firmware. The NC pins (46-48, 60-64) MUST be left floating, not grounded - the internal ESD structure relies on these pins being no-connect.
Route SPI signals (SDI/SDO/SCLK/CSN) as a 4-wire bus with ground reference on both sides; keep them at least 5 mm away from OUT21-OUT28 switching nodes. Use series 100 ohm resistors at the SPI outputs near the L9779WDAT2 to damp ringing on the rising edges, especially if the ECU MCU is on a separate ground-referenced island. The WDI/WDO watchdog signals should be kept short and direct.
The L9779WDAT2's 5V/3.3V internal regulators source up to approximately 200 mA combined - de-rate by 50% at 150 C junction. If the ECU MCU + sensors exceed this current, add an external LDO or DC-DC pre-regulator upstream. Estimated: with all 28 driver channels switching at 1 kHz PWM, additional 50 mA is drawn from VS for gate charge; ensure the upstream pre-regulator handles dynamic load steps.
معلومات الامتثال
AEC-Q100 grade-0 qualified per ST product page (automotive category). RoHS and REACH compliance per ST automotive product family policy. Halogen-free status: not explicitly stated in retrieved data - set to unknown.
