onsemi

LM224DTBG - Low-Power Quad Op Amp, 3-32 V | onsemi

MPN: LM224DTBG ✓ نشط
3 V to 32 V Vdss 14-TSSOP Package
الحد الأدنى للطلب: 1 |

LM224DTBG نظرة عامة

onsemi LM224DTBG is a low-power, general-purpose quad operational amplifier with four amplifier channels, a 3 V to 32 V supply-voltage range, and a 14-pin TSSOP package. The device is specified for operation from -25°C to +85°C and is intended for instrumentation, buffering, and general-purpose signal-conditioning applications.

An operational amplifier, or op amp, is an integrated voltage amplifier whose open-loop gain and feedback behavior allow it to perform precision amplification, buffering, summation, integration, and filtering. A quad operational amplifier combines four amplifiers in one package, allowing compact implementation of multi-channel analog systems. Within the component hierarchy, the LM224 belongs to the operational-amplifier, analog-amplifier, analog-signal-conditioning, and integrated-circuit categories.

The LM224DTBG provides four independent general-purpose amplifier channels in one 14-TSSOP package, reducing external component count and board area compared with four separate single or dual amplifier packages. Its stated 3 V to 32 V operating range supports both lower-voltage and higher-voltage analog systems. The -25°C to +85°C temperature specification supports industrial-temperature applications where the operating environment exceeds the commercial range.

The quad-channel architecture is particularly useful when four related analog signals must be conditioned under common supply and layout constraints. Because all four amplifiers share one package, power routing and grounding can be organized consistently across the device. Designers should still evaluate each channel independently for output swing, input common-mode range, noise, stability, and load-drive requirements during final circuit verification.

Typical uses include sensor-signal conditioning, transducer-buffer interfaces, analog measurement chains, audio and communication equipment, low-frequency active filtering, and general instrumentation. The LM224DTBG can also serve as a quad amplifier in industrial control systems where three or four channels are needed for excitation, sensing, filtering, or output buffering without using multiple packages.

PCB implementation requires careful attention to feedback-loop stability, input and output grounding, and decoupling. Place the power-supply bypass capacitor close to the supply pins, keep feedback traces short, and avoid routing sensitive inputs beside high-current outputs. Because the package exposes 14 terminals in a compact TSSOP footprint, inspect land patterns and solder-paste design before assembly.

This product page consolidates the exact package, channel count, supply range, temperature range, sourcing information, drop-in comparison, and application guidance for LM224DTBG. It also provides practical selection criteria for comparing this onsemi quad amplifier with the documented LM224DTBR2G alternative and with pin-compatible single-supply amplifier families.

بدائل مباشرة لـ LM224DTBG — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

LM224DTBR2G

✅ بديل مباشر
📦 14-TSSOP
Same 14-TSSOP four-channel footprint; some electrical characteristics differ, while the published comparison identifies the parts as functionally similar

📋 بديل مرجعي (غير موجود في الكتالوج)

LM224DTBG الحدود القصوى والخصائص الكهربائية

Product Type Quad general-purpose operational amplifier
Number of Amplifier Channels 4 channels
Supply Voltage Range 3 V to 32 V
Maximum Total Supply Voltage 32 V
نطاق درجة حرارة التشغيل -25°C to +85°C
العلبة 14-TSSOP
Package Pin Count 14 pins
Power Class Low-power operational amplifier
Amplifier Classification General-purpose amplifier
Primary Functions Instrumentation, op amp, buffer amplifier
نوع التركيب Surface mount
Number of Inputs per Channel 2 inputs
Number of Outputs per Channel 1 output

دليل تكوين أطراف LM224DTBG 14 pins

تكوين الأطراف لـ LM224DTBG (حزمة 14 pins). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 14 pins لـ LM224DTBG

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM224DTBG.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LM224DTBG مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Transducer Buffering, Low-Frequency Active Filters, Audio and Communication Interfaces, Process Control Output Buffering, Portable Measurement Equipment.

🏭

Industrial Sensor Signal Conditioning

LM224DTBG is well suited to conditioning several low-frequency sensor signals within an industrial measurement system. Four integrated general-purpose amplifier channels can provide buffering, gain, summing, or active filtering without requiring four separate packages. The 3 V to 32 V operating range supports varied supply architectures, while the -25°C to +85°C specification covers moderately extended industrial environments. Designers should verify the input common-mode range, output swing, and offset requirements for the chosen sensor and excitation level. Feedback components should be placed close to the associated amplifier pins, and sensitive input routes should remain separated from output and supply-current paths to minimize coupling.

📡

Transducer Buffering

LM224DTBG can buffer high-impedance sensor or transducer outputs before they enter a measurement, conversion, or communications stage. Its four amplifier channels allow up to four buffered outputs to share the same 14-TSSOP package and supply arrangement, helping reduce board area. The low-power classification supports portable and distributed measurement systems where power efficiency is important. At the circuit level, high source impedance can interact with input bias current and capacitance, so the sensor return path and guarding strategy require careful layout. Confirm the amplifier’s input bias current and common-mode limits against the transducer impedance before finalizing the schematic.

🔧

Low-Frequency Active Filters

LM224DTBG is appropriate for low-frequency active-filter stages requiring several amplifier channels, such as multi-stage anti-alias filters, smoothing filters, or signal-conditioning filters in instrumentation. The quad package provides four amplifiers that can implement cascaded sections, buffered summing networks, or gain stages. The 3 V to 32 V supply range permits operation across multiple industrial and embedded rails. Stability depends on the selected gain, feedback network, source impedance, and capacitive loading, so simulate the complete topology rather than evaluating each stage in isolation. Maintain short feedback paths and place compensation or filter capacitors according to the chosen transfer function to preserve expected phase margin.

🎧

Audio and Communication Interfaces

LM224DTBG can support low-frequency audio and communication interface functions where multiple buffered channels are needed, including receive-buffer, mixing, and gain stages around external converters. Four amplifiers in one 14-TSSOP package simplify routing and conserve board area compared with separate multi-amplifier packages. Its 3 V to 32 V supply range accommodates common embedded and industrial system rails. Audio-path designs must account for output swing, capacitive loading, channel-to-channel behavior, and the bandwidth required by the signal. Keep output routing separated from high-impedance inputs, provide a low-impedance ground reference, and verify stability with the actual load and feedback values.

⚙️

Process Control Output Buffering

LM224DTBG can buffer control and monitoring outputs in an industrial process-control assembly where three or four channels must be driven consistently. Typical uses include scaling sensor-derived control signals, buffering voltage references for downstream converters, and providing isolation buffers between measurement and actuator stages. The quad topology and -25°C to +85°C rating fit equipment operating above a commercial-temperature environment. Each output should be checked for the intended load, because capacitive loading and the selected gain can affect stability. Keep output current paths away from precision sensor inputs and use local supply bypassing to prevent transient behavior from propagating between controlled channels.

📱

Portable Measurement Equipment

LM224DTBG fits portable measurement instruments that combine several low-frequency analog channels with limited board space. Its low-power quad operational-amplifier architecture can buffer inputs, implement gain stages, and support channel multiplexing within one 14-TSSOP package. The 3 V minimum supply rating is useful for compact systems operated from regulated battery-derived rails, while the 32 V maximum provides flexibility for industrial variants. Power budget and thermal performance should be evaluated over the full battery range. Low-noise layout, short feedback loops, and a common ground reference are particularly important when measuring small sensor outputs, because long PCB traces and shared return paths can undermine accuracy.

What are the key specifications of LM224DTBG that engineers should know?
The LM224DTBG is a four-channel, general-purpose operational amplifier operating from 3 V to 32 V in a 14-pin TSSOP package. Its specified temperature range is -25°C to +85°C. According to the onsemi LM224 datasheet, the device is optimized for low-power operation, while its four-amplifier configuration consolidates multiple analog channels into one surface-mount package. These headline characteristics make it suitable for instrumentation, buffering, and general signal-conditioning circuits.
Where can I download the LM224DTBG datasheet PDF?
The LM224DTBG datasheet is available through the onsemi LM224DTBG datasheet page, with a downloadable PDF listing the device as a single-supply quad operational amplifier. The document is identified as 14 pages in the source index. Use the manufacturer pin-description and electrical-characteristics tables when assigning PCB connections, selecting bypass capacitors, and checking the -25°C to +85°C operating specification.
Where can I find the LM224DTBG pinout?
The LM224DTBG uses a 14-TSSOP package containing four operational amplifiers. Use the manufacturer datasheet pin-description table and the package drawing to confirm each channel’s input, output, supply, and ground connections before routing the PCB. The exact terminal assignments are not reproduced on this page because the indexed result confirms the 14-terminal package but does not expose the complete pin-description table.
Is LM224DTBG suitable for single-supply operation?
Yes. LM224DTBG is identified as a single-supply quad operational amplifier with a 3 V to 32 V operating range. This makes it appropriate for systems that cannot provide a negative analog supply. The final design must still verify the required input and output common-mode ranges, output swing, and load conditions at the selected supply voltage before the circuit is released for production.
What is the difference between LM224DTBG and LM224DTBR2G?
LM224DTBG and LM224DTBR2G are both listed as 14-TSSOP, four-channel general-purpose operational amplifiers from onsemi. Published comparisons characterize their main electrical parameters as broadly similar, although some characteristics differ and should be checked before substitution. The most important qualification question is whether the replacement’s temperature grade and exact ordering code satisfy the target product’s environmental and procurement requirements.
When should I choose LM224DTBG over another quad op amp?
Choose LM224DTBG when the design needs four general-purpose amplifier channels, accepts a supply between 3 V and 32 V, and fits a 14-TSSOP footprint. Its -25°C to +85°C temperature specification is preferable to commercial-grade devices in moderately extended industrial environments. Select another amplifier when its bandwidth, noise, offset, common-mode range, output swing, or AEC-Q100 qualification better matches the application.
Is LM224DTBG suitable for industrial sensor conditioning?
LM224DTBG is suitable for many industrial sensor-conditioning stages because it combines four channels, 3 V to 32 V operation, and a -25°C to +85°C temperature range. It can buffer sensor outputs or participate in gain and filtering stages. Confirm input common-mode limits, output swing, noise, offset, and stability with the actual sensor impedance and supply before selecting the amplifier.
What can replace LM224DTBG?
LM224DTBR2G is the clearest documented drop-in candidate for LM224DTBG because it uses the same 14-TSSOP format and is compared as a closely related onsemi quad general-purpose amplifier. A valid replacement must preserve the channel count, package footprint, pin functions, supply range, and required temperature range. Review the manufacturer comparison and application requirements before approving the substitution.
Is LM224DTBG the same as LM224DTBR2G?
LM224DTBG and LM224DTBR2G are closely related but are not identical ordering codes. Both are presented as 14-TSSOP quad general-purpose operational amplifiers, and published comparisons report similar functional characteristics with some electrical differences. Treat LM224DTBR2G as a drop-in candidate for engineering review, not as an unconditional substitution, until temperature grade, electrical limits, and qualification requirements have been confirmed.
What is the best cross-brand equivalent for LM224DTBG?
A cross-brand equivalent must retain the four-channel topology, 14-TSSOP footprint, pin-to-pin assignments, 3 V to 32 V supply capability, and required temperature performance. The manufacturer cross-reference resources are suitable starting points, but they do not by themselves establish unconditional drop-in equivalence. Use the Request a Quote form on this page for exact LM224DTBG sourcing, and validate any substitute against the complete manufacturer electrical table.
Can LM224DTBR2G replace LM224DTBG in a PCB design?
LM224DTBR2G can serve as a drop-in replacement candidate because it uses the same 14-TSSOP package and a closely related four-channel general-purpose amplifier configuration. Before replacing LM224DTBG, compare pin functions, supply range, input common-mode range, output swing, offset, bandwidth, quiescent current, and operating temperature. The documented similarity supports compatibility, but the final approval must follow a full manufacturer-specification review.
How should LM224DTBG be placed on a PCB?
Place the power-supply bypass capacitor close to the device supply pins, connect the ground pins to a low-impedance ground plane, and keep each amplifier’s feedback path short. Avoid routing sensitive input traces beside output traces that can carry higher signal currents. Stable feedback design, controlled grounding, and correct TSSOP land geometry are essential for preserving analog performance and avoiding unintended oscillation.
Where can I buy LM224DTBG online?
Use the Request a Quote form on this page to request LM224DTBG availability, lot availability, and ordering information. The request should identify the exact 14-TSSOP ordering code and any required quantity, temperature, qualification, or date-code criteria. This avoids ambiguity between different manufacturers’ LM224 variants and helps procurement confirm the correct onsemi part.
What is the price of LM224DTBG?
Current commercial pricing for LM224DTBG should be obtained through the Request a Quote form on this page because market conditions and quantity determine the final quotation. Provide the required order quantity, packaging preference, target date, and any production or traceability requirements. The form also helps distinguish LM224DTBG from related LM224 ordering codes that use different packages or qualification grades.
What is the lead time and stock status for LM224DTBG?
Request the current lead time, minimum order quantity, and stock status through the Request a Quote form on this page. Include your required quantity, approved supplier list, target delivery date, and production schedule. The exact LM224DTBG ordering code is a 14-TSSOP onsemi quad operational amplifier, which allows sourcing personnel to confirm the precise package and grade before committing a delivery schedule.

بيانات مرجعية هندسية لـ LM224DTBG — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LM224DTBG when a design needs four general-purpose operational amplifiers, a 3 V to 32 V supply range, and a 14-TSSOP footprint. It is particularly suitable for instrumentation, sensor buffering, active filtering, and industrial-temperature systems that operate from -25°C to +85°C. LM224DTBR2G is the closest documented drop-in candidate when its exact electrical limits and qualification grade satisfy the design, but its temperature and order-code requirements must be checked. For new designs, compare the LM224 with higher-performance amplifier families when noise, offset, bandwidth, slew rate, rail-to-rail input or output behavior, or AEC-Q100 qualification is required. Use a dual amplifier only when the circuit needs two channels rather than four, and retain the LM224DTBG when package count, common supply routing, or board-area reduction is important.

المقارنة مع البدائل

المعامل هذا المنتج LM224DTBR2G
Brand onsemi onsemi
Package 14-TSSOP 14-TSSOP
Amplifier Channels 4 channels 4 channels
Supply Voltage Range 3 V to 32 V 3 V to 32 V
Amplifier Type General-purpose, low-power operational amplifier General-purpose operational amplifier
Supply Configuration Single supply Single supply

أبرز الفروقات

  • Four general-purpose channels in one compact package (مقابلLM224DTBR2G)
  • Single-supply operation across a broad voltage range (مقابلLM224DTBR2G)
  • Channel consolidation reduces package count (مقابلLM2902N/PB)

ملاحظات التصميم

Assign each amplifier channel to a continuous ground reference and place the supply bypass capacitor adjacent to the device supply terminals. Keep output and feedback traces short, particularly when driving capacitive loads. For low-level sensor inputs, route away from supply-current paths and high-impedance nodes. These layout choices reduce coupling between the four channels and help maintain predictable analog performance across the 3 V to 32 V operating range.

Do not assume that two quad LM224 ordering codes are interchangeable merely because they use the same 14-TSSOP footprint. Compare LM224DTBG with LM224DTBR2G for input offset, bias current, bandwidth, output swing, slew rate, supply current, common-mode limits, and temperature grade. A footprint match establishes mechanical compatibility, while the electrical comparison establishes whether the replacement is appropriate for the actual channel configuration.

Evaluate the complete analog channel rather than only the nominal supply rating. The LM224DTBG supports 3 V to 32 V, but usable signal range depends on the selected supply and the amplifier’s input and output limits. At low supply voltages, verify common-mode headroom and output swing. At higher voltages, confirm operating temperature and channel power dissipation so the TSSOP package remains within its intended thermal environment.

Keep feedback loops physically compact and connect the noninverting input directly to its defined reference. High source impedances can combine with input capacitance to alter gain and phase, particularly in sensor-buffer applications. Use an appropriate return path, avoid routing inputs beneath noisy analog stages, and verify stability with the actual source and load impedances before production release.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status is present in the indexed product information. The -25°C to +85°C operating range is an environmental specification and does not establish AEC-Q100 qualification.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LM224DTBG datasheet LM224DTBG datasheet pdf LM224DTBG pinout LM224DTBG schematic onsemi LM224DTBG LM224DTBG 14-TSSOP LM224DTBG quad op amp LM224DTBG 3-32V LM224DTBG vs LM224DTBR2G LM224DTBG equivalent LM224DTBG replacement LM224DTBG price LM224DTBG stock LM224DTBG sensor conditioning LM224DTBG low power amplifier

المكونات والمصطلحات ذات الصلة

onsemi LM224DTBG LM224DTBR2G LM224DT LM2902N/PB LM324ADR LM324NSR LM2904PWR operational amplifier quad operational amplifier analog amplifier signal-conditioning IC integrated circuit single-supply amplifier 14-TSSOP TSSOP package family surface-mount package 3 V to 32 V -25°C to +85°C instrumentation sensor signal conditioning active filter transducer buffer low-power electronics
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر