LM2902VDTB - Quad 3-26V Low-Power Op Amp | onsemi
MPN: LM2902VDTB ✓ نشطLM2902VDTB نظرة عامة
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its differential inputs. The LM2902 belongs to the general-purpose operational-amplifier family within the broader hierarchy of amplifier ICs, analog ICs, and semiconductors. Its true differential-input architecture is particularly useful in single-supply circuits because the input common-mode range extends close to the positive supply rail, allowing signals to be measured without a separate negative supply in many designs.
The LM2902 provides four amplifier circuits per package, a 3 V to 26 V operating supply range, and low-power operation in a 14-TSSOP package. These characteristics make it a practical choice for sensor interfaces, current measurements, voltage comparisons, audio signal paths, and general feedback-control circuits. Compared with a discrete single op amp, the integrated quad reduces component count and simplifies power distribution while preserving independent channels for multiple analog functions.
Each channel includes the core functionality expected from a general-purpose amplifier: differential input handling, high open-loop gain, single-supply operation, and output-stage drive suitable for common low-frequency analog networks. Because the four channels share one package, their supply pins and ground reference are common, but the channels remain independent amplifiers. This architecture is useful when one circuit performs input buffering, another provides gain, and two additional channels implement filtering or threshold comparisons.
Typical applications include sensor signal conditioning in industrial systems, audio preamplification, low-voltage logic threshold detection, closed-loop control, current sensing with a sense resistor, and general-purpose instrumentation. The 14-TSSOP outline also helps reduce board area compared with four individual SOIC-8 packages, although the relatively narrow lead pitch requires careful PCB layout and clean assembly practices.
When connecting the LM2902VDTB, verify input and output voltage limits against the selected supply configuration, including the effects of ground offsets and saturation. Decoupling capacitors should be placed close to the supply pins, while sensitive analog traces should remain short and away from switching nodes. The manufacturer datasheet should be used for exact pin assignments, input common-mode limits, output swing, electrical characteristics, and recommended application circuits.
This product page combines the manufacturer device identity with package and supply information, engineering-focused application guidance, drop-in replacement analysis, and practical PCB considerations. It supports faster component selection while directing engineers to the authoritative onsemi datasheet for design-critical electrical limits and package details.
بدائل مباشرة لـ LM2902VDTB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM2902VDTB (نفس عامل الشكل والبصمة) — يختلف في Package, Number of Channels, Power Class, Product Type.
LM2902VDTBR2G
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2902VDTBR2
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2902DTB
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2902VDTBG
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2902VDTB الحدود القصوى والخصائص الكهربائية
| Number of Amplifier Channels | 4 circuits |
| جهد التغذية التشغيلي | 3 V to 26 V |
| Power Class | Low power |
| Input Architecture | True differential inputs |
| العلبة | 14-TSSOP |
| نوع التركيب | Surface mount |
| Product Category | General-purpose operational amplifier |
| Number of Channels | 4 |
دليل تكوين أطراف LM2902VDTB 14-tssop
تكوين الأطراف لـ LM2902VDTB (حزمة 14-tssop). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM2902VDTB.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM2902VDTB مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Audio Preamplification, Current-Sense Amplifier, Threshold Detection and Logic Interface, Closed-Loop Control, General-Purpose Instrumentation.
Industrial Sensor Signal Conditioning
The LM2902VDTB suits industrial sensor interfaces because four channels can buffer, amplify, filter, and compare signals without requiring four separate amplifier packages. Its 3 V to 26 V operating range covers common regulated and industrial supply levels, while true differential inputs help process sensor voltages referenced to a shared ground. Place the amplifier close to the sensor and ADC input, use short grounded traces, and decouple the supply pins to reduce pickup. The principal trade-off is general-purpose performance: applications requiring extremely low offset, rail-to-rail output, or very high bandwidth should use a more specialized amplifier.
موصى به
Audio Preamplification
The LM2902VDTB can provide multiple gain stages for low-frequency audio paths because it contains four general-purpose operational-amplifier channels in one 14-TSSOP package. The 3 V to 26 V supply range supports several portable and fixed-system supply arrangements, and the low-power design avoids the excess dissipation associated with unnecessary amplifier stages. Use each channel for a defined gain or filtering function and keep feedback components close to their associated pins. Confirm the required output swing and bandwidth against the manufacturer datasheet before using the device for high-fidelity or high-drive applications.
موصى به
Current-Sense Amplifier
A low-side shunt-current measurement circuit can use one LM2902VDTB channel to amplify the small differential voltage generated across a sense resistor. The device's true differential-input architecture helps reject common-mode voltage, and its 3 V to 26 V operating range supports operation from low-voltage and industrial rails. Additional channels can monitor the shunt voltage, implement a threshold, or filter the amplified output. Select resistor and feedback values for the intended gain, verify that signal common-mode voltage stays within the datasheet limits, and connect the supply return cleanly to minimize ground-offset error.
موصى به
Threshold Detection and Logic Interface
The LM2902VDTB is useful for translating a slowly varying analog condition into a threshold decision. One channel can compare a sensor voltage against a reference, while other channels can buffer the reference, amplify the decision signal, or provide additional comparisons. Its 3 V to 26 V supply range permits operation across many 5 V, 12 V, and higher industrial rails, and the four-channel package simplifies multi-channel monitoring. For reliable detection, allow the comparator input to cross the threshold with adequate noise margin and observe the output-swing limits stated in the onsemi datasheet.
موصى به
Closed-Loop Control
The LM2902VDTB can implement basic closed-loop controllers where four analog channels are required on a compact board. Typical arrangements use one channel in a feedback amplifier, another to shape a reference, and two channels to control auxiliary stages or monitor system conditions. The low-power quad architecture reduces package count, while the 3 V to 26 V supply range accommodates several industrial control environments. Check loop stability, output-current capability, capacitive-load behavior, and saturation recovery against the manufacturer datasheet, particularly when driving long cables or slow actuator inputs.
موصى به
General-Purpose Instrumentation
The LM2902VDTB is well suited to bench and field instrumentation that needs several low-frequency analog functions in one package. Four channels can handle input buffering, gain, active filtering, and output conditioning while operating from a 3 V to 26 V source. The 14-TSSOP footprint reduces board area compared with separate single-channel packages, and true differential inputs are useful for measurement nodes with small signal differences. Keep sensitive inputs away from motor, relay, and switching-regulator traces, provide local bypass capacitance, and validate offset and noise performance against the minimum system accuracy requirement.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2902VDTB — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM2902VDTBR2G | LM2902VDTBR2 | LM2902DTB | LM2902VDTBG |
|---|---|---|---|---|---|
| Package | TSSOP-14 | TSSOP-14 - same | TSSOP-14 - same | TSSOP-14 - same | TSSOP-14 - same |
| Brand | onsemi | onsemi | onsemi | onsemi | onsemi |
| Number of Amplifier Channels | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Operating Supply Voltage | 3 V to 26 V | 3 V to 26 V | 3 V to 26 V | 3 V to 26 V | 3 V to 26 V |
| Product Category | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier | General-purpose operational amplifier |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount | Surface mount |
أبرز الفروقات
- Matches the identified 14-TSSOP LM2902 replacement architecture (مقابلLM2902VDTBR2G)
- Direct family replacement with matching channel count and voltage range (مقابلLM2902VDTBR2)
- Site-linked onsemi ordering option with the same identified footprint (مقابلLM2902DTB)
ملاحظات التصميم
Place the local supply bypass capacitor directly between the LM2902VDTB supply and ground pins, and keep the connection as short as practical. The 14-TSSOP footprint has a narrow lead pitch, so long loops around the package can increase inductive impedance and allow switching noise to enter the amplifier inputs. Route sensitive input and feedback nets away from power converters, relays, inductors, and high-current return paths.
Assign one physical function to each amplifier channel and keep each input, feedback component, and output connection localized around that channel. Avoid sharing long feedback traces between channels because capacitive coupling in a compact TSSOP layout can create oscillation or crosstalk. Where differential inputs are used, route the positive and negative conductors together and terminate the source close to the amplifier to reduce common-mode pickup.
Do not assume that a quad operational amplifier can operate with inputs or outputs arbitrarily close to the negative or positive supply rail. Consult the onsemi LM2902 datasheet for input common-mode range, output swing, supply-current, and stability limits. Also avoid using the device as a general-purpose comparator without accounting for propagation delay, saturation behavior, and output swing when the input crosses the threshold.
For low-level sensor measurements, minimize ground offsets by returning shunt or sensor current through the same ground structure used by the amplifier. Keep feedback resistors physically close to their associated pins and avoid routing the output near sensitive inputs. If the source has high source impedance, add an appropriate buffer stage or verify that the selected biasing produces acceptable offset and bandwidth behavior.
معلومات الامتثال
Use the current onsemi LM2902 product documentation and orderable-part declarations for environmental and material-compliance requirements.