LM258ADRG4 - Dual 30V 700kHz Op Amp | Texas Instruments
MPN: LM258ADRG4 ✓ نشطLM258ADRG4 نظرة عامة
An operational amplifier is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. The LM258A belongs to the operational-amplifier hierarchy, which includes general-purpose amplifiers, precision amplifiers, instrumentation amplifiers, and comparators. Its two independently compensated channels can implement buffer, gain, summing, active-filter, transducer, and feedback-control circuits from a single or split power supply.
The headline features are 700 kHz bandwidth, 0.3 V/µs slew rate, and ±1.5 V to ±16 V operating range. Typical input offset voltage is 3 mV, while typical input offset current is 2 nA and typical input bias current is 15 nA. The common-mode input range includes ground, making the device useful for circuits that process low-level signals close to the negative supply rail. Internal frequency compensation removes the need for an external compensation network.
Internally, the LM258A uses two frequency-compensated amplifier sections optimized for general-purpose signal conditioning. Its moderate bandwidth supports audio and control applications without requiring the speed or precision of a dedicated high-voltage amplifier. The architecture is intended for broad supply-voltage operation, useful in industrial equipment powered from unregulated rails and in split-supply analog circuits. The maximum-rated differential input range is 32 V, subject to the device's absolute maximum conditions.
Typical applications include low-level sensor signal conditioning, active filtering, audio preamplification, relay and actuator drive interfaces, power-supply feedback, and dual-channel industrial control loops. Using one package for two channels can also reduce board area when both channels require similar common-mode and supply characteristics. The operating-temperature grade supports commercial and industrial ambient conditions rather than the full automotive temperature range.
Design should preserve adequate input and output voltage headroom, account for offset when sensing near ground, and place input-referenced error sources close to the amplifier. Decoupling capacitors should be placed directly across the supply pins, while sensitive feedback nodes require short traces and careful grounding. Verify source and sink current capability against the intended load because a wide supply range alone does not guarantee adequate output-current margin.
This page combines the Texas Instruments product specifications, package and pin information, sourcing guidance, engineering design notes, and a pin-compatible comparison with other dual operational amplifiers. It is intended to accelerate component selection, PCB planning, and replacement assessment for engineers working with the LM258ADRG4 in 8-pin SOIC designs.
بدائل مباشرة لـ LM258ADRG4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM258ADRG4 (نفس عامل الشكل والبصمة) — يختلف في Package, Slew Rate, Amplifier Type, Common-Mode Input Range, Gain-Bandwidth Product.
LM358DR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM358DT
✅ بديل مباشر✓ متوفر في المخزون
$0.0509 / وحدة
عرض ورقة البيانات ←LM258DT
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM258ADRG4 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 700 kHz |
| Slew Rate | 0.3 V/µs |
| Supply Voltage Range | ±1.5 V to ±16 V |
| Maximum Total Supply Voltage | 32 V |
| Typical Input Offset Voltage | 3 mV |
| Typical Input Offset Current | 2 nA |
| Typical Input Bias Current | 15 nA |
| Typical Supply Current | 0.7 mA |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | 32 V |
| نطاق درجة حرارة التشغيل | -25°C to 85°C |
| العلبة | 8-pin SOIC (D) |
| Package Width | 3.90 mm |
| نوع التركيب | Surface mount |
| Frequency Compensation | Internal |
تكوين أطراف LM258ADRG4
| دبوس 1 | OUT1 — Output of amplifier channel 1 |
| دبوس 2 | -IN1 — Inverting input of amplifier channel 1 |
| دبوس 3 | +IN1 — Non-inverting input of amplifier channel 1 |
| دبوس 4 | V− — Negative supply or ground connection |
| دبوس 5 | +IN2 — Non-inverting input of amplifier channel 2 |
| دبوس 6 | -IN2 — Inverting input of amplifier channel 2 |
| دبوس 7 | OUT2 — Output of amplifier channel 2 |
| دبوس 8 | V+ — Positive supply connection |
التطبيقات النموذجية
LM258ADRG4 مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Active Audio Filtering, Power-Supply Feedback Control, Actuator and Relay Drive, Portable Instrumentation Front End, DC Motor and Valve Position Control.
Industrial Sensor Signal Conditioning
The LM258ADRG4 is suitable for amplifying low-level transducer outputs in industrial monitoring circuits because its common-mode input range includes ground and its supply capability reaches ±16 V. Each channel can provide voltage gain around 700 kHz or less, making the amplifier useful for temperature, pressure, and position sensors that require signal amplification before conversion or control. A typical implementation uses the non-inverting input as the sensor input and applies feedback from the output to the inverting input. Keep the sensor return and amplifier ground on the same reference network to prevent ground differences from appearing as input error. With a 3 mV typical input offset voltage, the design is more appropriate for signals well above the millivolt level or for applications where offset can be calibrated at the system level.
موصى به
Active Audio Filtering
The LM258ADRG4 can implement active low-pass or band-pass sections around audio-band signals because its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful bandwidth beyond the base-audio range. Two independently usable channels allow a stereo filter or a second-order filter to be distributed across one IC. RC components around each amplifier determine the filter response, so their tolerances and the amplifier’s 3 mV typical offset directly influence signal integrity. Confirm the output can remain within the required swing at the selected supply voltage. For low-level microphone signals, the common-mode range including ground is useful, but input bias current through the source impedance can create input-referred voltage error that should be included in the noise budget.
موصى به
Power-Supply Feedback Control
The LM258ADRG4 can amplify the error voltage in a linear regulator feedback loop, and its wide operating range of ±1.5 V to ±16 V supports laboratory and industrial supply designs. In a typical topology, one amplifier senses a divided output voltage and drives a feedback element or error amplifier stage. The 700 kHz gain-bandwidth product can respond to loop dynamics above baseband while the 0.3 V/µs slew rate limits how quickly the output can follow error corrections. Compensation values must be calculated with the actual pass device and load because amplifier bandwidth alone does not establish loop stability. The -25°C to 85°C operating range also allows operation across commercial and industrial ambient conditions, subject to the complete system’s thermal and accuracy requirements.
موصى به
Actuator and Relay Drive
The LM258ADRG4 can serve as the error amplifier in relay, solenoid, or actuator-control loops where the feedback network determines the commanded output level. Its 700 kHz gain-bandwidth product provides useful response margin, while the wide ±16 V supply capability accommodates higher-voltage control systems when the output current remains within the amplifier’s limits. The output stage must not be treated as a general power driver; use a suitable transistor when the load requires current beyond the op-amp output capability. Keep feedback routing short and place the output-transistor drive network so switching transients do not couple into the sensitive input node. The amplifier’s 3 mV typical input offset voltage becomes less significant when the loop gain and system resolution are high enough to reject it.
موصى به
Portable Instrumentation Front End
The two channels of the LM258ADRG4 are useful for portable instrumentation that requires buffering or modest gain close to a sensor. Operation from a single supply is possible because the common-mode input range includes ground, while the 0.7 mA typical supply current helps limit consumption in compact systems. A dual package can reduce the component count when buffering a reference and conditioning a measurement channel. Designers should still account for the 15 nA typical input bias current and 2 nA typical input offset current, particularly with high-impedance sensors. Verify battery-voltage variation against the ±1.5 V minimum supply requirement, and use decoupling capacitors close to pins 4 and 8 to keep supply noise from coupling into the measurement path.
موصى به
DC Motor and Valve Position Control
The LM258ADRG4 can form an error amplifier in a position-control or current-feedback loop for small DC actuators. Its 700 kHz gain-bandwidth product and 0.3 V/µs slew rate provide useful loop dynamics, while the two amplifier channels can handle related signal tasks when their grounding and loading remain compatible. The op-amp should generally drive a separate power transistor rather than the motor or valve coil directly. Account for the amplifier’s 3 mV typical offset in the position-error budget, and ensure that the control loop remains stable across the expected supply voltage and load. If the circuit is exposed to motor switching noise, keep power-current paths separate from input and feedback traces and provide local supply bypassing at the package pins.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM258ADRG4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM358DR | LM358DT | LM258DT |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | STMicroelectronics | STMicroelectronics |
| Package | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) | 8-pin SOIC (D) |
| Amplifier Configuration | Dual general-purpose operational amplifier | Dual general-purpose operational amplifier | Dual operational amplifier | Dual operational amplifier |
أبرز الفروقات
- Defined 700 kHz bandwidth and 0.3 V/µs slew rate (مقابلLM358DR)
- Common-mode operation down to ground (مقابلLM358DT)
- Single 8-pin SOIC package provides two amplifiers (مقابلLM258DT)
- Specified commercial and industrial ambient range (مقابلLM358DR)
ملاحظات التصميم
Place the supply-bypass capacitor directly between pins 8 and 4, with the ground end connected to the quiet ground plane. Keep the two input and two output traces short, and route feedback components close to their associated amplifier pins. The inverting input is sensitive to parasitic capacitance, so avoid routing it beside high-impedance input or switching-node traces. A solid ground plane and short return paths reduce common-mode pickup and maintain predictable operation across both channels.
Do not assume that the common-mode input range includes ground under every output and supply condition. Check the input common-mode range and output swing curves in the manufacturer datasheet against the actual signal range. When operating from a single supply, leave sufficient output headroom for the load. Also account for 3 mV typical input offset, 15 nA typical input bias current, and 2 nA typical input offset current when resolving small signals.
Estimated: with a 0.7 mA typical supply current and a 5 V single supply, LM258ADRG4 power dissipation is approximately 0.0035 W. This estimate uses 0.7 mA supply current and 5 V supply voltage and excludes load-current dissipation in external circuitry. At ±16 V, supply-current dissipation rises in proportion to the supply voltage, so thermal review should use the highest operating supply and actual measured or worst-case supply current.
When one channel performs low-level sensing and the other handles a faster control function, retain a common ground reference but avoid sharing sensitive feedback nodes. The two channels are independent, yet poor grounding can couple output transients into an adjacent input. Use separate passive filtering only where its effect on phase margin is acceptable, and verify that added RC networks do not unintentionally reduce stability in a feedback loop.
معلومات الامتثال
The product is an operational amplifier rather than an automotive-qualified device. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current manufacturer product documentation or the Request a Quote form.