Texas Instruments

LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments

MPN: LM2901DE4 ✓ نشط
2 V to 30 V Vdss 3.5 nA Id 14-SOIC, 0.154 inch width, 3.90 mm width Package
الحد الأدنى للطلب: 1 |

LM2901DE4 نظرة عامة

The Texas Instruments LM2901DE4 is a quad differential comparator with open-collector outputs, designed for single-supply operation from 2 V to 30 V or split-supply operation within the stated common-mode limits. The device contains four independent comparator channels in a 14-pin SOIC package, with a typical input offset voltage of 0.37 mV and an input bias current of 3.5 nA. Each channel can compare two input voltages and provide a logic-level indication through an open-collector output. The LM2901DE4 is suitable for industrial control, sensor interfacing, threshold detection, voltage monitoring, and general-purpose signal conditioning applications. Its low supply current of approximately 200 uA per comparator and wide operating temperature range of -40 °C to +125 °C make it practical for both commercial and extended-temperature equipment. The open-collector outputs allow wired-AND operation and require an external pull-up resistor when the output must drive a logic high.

A differential comparator is an analog integrated circuit that compares two voltage inputs and changes its output state according to their relative voltage. The LM2901 belongs to the comparator category within the broader interface IC hierarchy, where analog front-end decision-making is followed by digital logic, control, or measurement. Unlike an operational amplifier, the comparator is intended primarily for threshold crossing and does not provide linear amplification. The LM2901 family combines four channels in one package, allowing a compact design when multiple independent decisions are needed. Its common-mode input range includes ground, making it useful in systems powered from a single positive rail where the signal being compared can approach 0 V.

Key features include a maximum supply rating of 38 V, a low input offset voltage of 0.37 mV, an input bias current of 3.5 nA, and low supply-current consumption of approximately 200 uA per comparator. The open-collector output structure is compatible with TTL, MOS, and CMOS logic when the appropriate pull-up is used. The comparator also supports a faster response time than many older standard quad comparators. Because all four channels share the same supply pins, the device is most appropriate when the compared signals operate within the same supply system. The 14-SOIC package provides a conventional surface-mount footprint and broad compatibility with industrial control-board layouts.

The internal architecture uses four differential comparator channels referenced to the common ground and supply rails. The input stage is designed for low offset and low bias current, reducing errors when small signal differences must be detected. The open-collector transistor remains off when the comparator output is high impedance and conducts when the output is driven low. The external pull-up resistor determines the high-state voltage and limits the current through the output transistor. The maximum differential input voltage and common-mode voltage limits must be respected during startup, fault conditions, and signal transients. The manufacturer datasheet is the authoritative source for absolute maximum ratings, electrical limits, timing characteristics, and the complete pin configuration.

Typical uses include monitoring a battery or power rail, detecting an overvoltage or undervoltage condition, comparing a thermistor or divider output with a reference, and providing a fault flag in industrial equipment. The four channels can also implement independent window comparisons when suitable resistor networks are used. Open-collector outputs are particularly useful when multiple comparators must signal one system event through a common pull-up node. In motor-control, power-supply, and instrumentation circuits, the device can provide a hardware threshold decision before a controller reacts, reducing the processing burden on the controller.

The principal design consideration is the pull-up network on every open-collector output. Select the resistor to balance rise time against output-transistor dissipation and required logic current. Keep comparator inputs away from noisy power-switching nodes, use a stable reference for precision thresholds, and account for input common-mode limits. When replacing another quad comparator, verify the complete pinout, output architecture, supply range, input offset, response time, and temperature rating before production use. The LM2901DE4 is a standard general-purpose choice for designs requiring four channels, wide supply tolerance, and flexible open-collector interfacing.

بدائل مباشرة لـ LM2901DE4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع LM2901DE4 (نفس عامل الشكل والبصمة) — يختلف في Logic Compatibility, Differential Input Voltage Range, Package, Comparator Type, Supply Voltage Range.

Texas Instruments
Logic Compatibility: TTL, CMOS, MOS, DTL, and ECL
Differential Input Voltage Range: ±1 V to ±18 V
Package: 14-pin SOIC
قارن مع LM2901DE4 →
Texas Instruments
Logic Compatibility: TTL, MOS, and CMOS compatible
Differential Input Voltage Range: -38 V to +38 V
Package: 14-pin SOIC
قارن مع LM2901DE4 →
Texas Instruments
Logic Compatibility: TTL, MOS, and CMOS
Differential Input Voltage Range: -38 V to +38 V
Package: 14-SOIC, 3.90 mm width
قارن مع LM2901DE4 →

LM2901D

✅ بديل مباشر
Texas Instruments
📦 14-SOIC
Quad differential voltage comparator · 4 channels · Single supply, 5 V to 36 V · ±1 V to ±18 V · 30 V · Open collector · 300 ns · 25 nA typical

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM2901DRE4

✅ بديل مباشر
📦 14-SOIC
Same 14-SOIC quad-comparator package and open-collector output architecture; suffix-specific rating and qualification must be checked

📋 بديل مرجعي (غير موجود في الكتالوج)

LM2901DG4

✅ بديل مباشر
Texas Instruments
📦 14-SOIC
Quad differential comparator · 4 channels · 30 V · 2 V to 36 V · 38 V · 0.37 mV · 3.5 nA · 200 µA per comparator

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM2901DR

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 14-SOIC
Same LM2901 quad-comparator family in a 14-SOIC footprint; tape-and-reel ordering code and suffix-specific qualification must be confirmed

📋 بديل مرجعي (غير موجود في الكتالوج)

LM2901DRE4

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 14-SOIC
Same 14-SOIC family variant; alternative status depends on the exact suffix and manufacturer ordering configuration

📋 بديل مرجعي (غير موجود في الكتالوج)

LM2901DE4 الحدود القصوى والخصائص الكهربائية

Comparator Type Quad differential comparator
Number of Channels 4 channels
نوع الخرج Open-collector
Supply Voltage Range 2 V to 30 V
Maximum Supply Rating 38 V
Input Offset Voltage 0.37 mV typical
Input Bias Current 3.5 nA
تيار التغذية 200 uA per comparator
Common-Mode Input Range Includes ground
Differential Input Voltage Range ±38 V
نطاق درجة حرارة التشغيل -40 °C to +125 °C
العلبة 14-SOIC, 0.154 inch width, 3.90 mm width
نوع التركيب Surface mount
Logic Compatibility TTL, MOS, and CMOS compatible with pull-up
ESD Rating HBM 2 kV
تكوين الخرج Wired-AND capable with external pull-up

تكوين أطراف LM2901DE4

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
دبوس 1 OUT1 — Comparator 1 open-collector output
دبوس 2 IN1- — Comparator 1 inverting input
دبوس 3 IN1+ — Comparator 1 non-inverting input
دبوس 4 GND — Ground
دبوس 5 IN2+ — Comparator 2 non-inverting input
دبوس 6 IN2- — Comparator 2 inverting input
دبوس 7 OUT2 — Comparator 2 open-collector output
دبوس 8 OUT3 — Comparator 3 open-collector output
دبوس 9 IN3- — Comparator 3 inverting input
دبوس 10 IN3+ — Comparator 3 non-inverting input
دبوس 11 VCC — Positive supply
دبوس 12 IN4+ — Comparator 4 non-inverting input
دبوس 13 IN4- — Comparator 4 inverting input
دبوس 14 OUT4 — Comparator 4 open-collector output

التطبيقات النموذجية

LM2901DE4 مناسب لـ 6 التطبيقs: Battery Voltage Monitoring, Industrial Threshold Detection, Thermistor and Resistive Sensor Conditioning, Power-Supply Overvoltage and Undervoltage Detection, Motor and Relay Control Logic, Test and Measurement Signal Qualification.

⚡

Battery Voltage Monitoring

The LM2901DE4 is suitable for monitoring a battery or power rail when the system requires a hardware threshold decision rather than relying only on firmware. Place one comparator channel across a resistor-divider output and a stable reference, then use the open-collector output to assert a fault signal when the monitored voltage crosses its limit. The 2 V to 30 V operating supply range supports many single-rail systems, while the low 200 uA per-comparator supply current helps preserve battery life. Because the output is open collector, a pull-up resistor can connect the fault indication to a supervisor, microcontroller input, or another comparator channel.

🏭

Industrial Threshold Detection

Use the LM2901DE4 for independent threshold detection in industrial control equipment, such as detecting an out-of-range control signal or converting an analog sensor condition into a logic event. Its four differential channels provide separate decisions while sharing a common supply and ground in one 14-SOIC package. The 0.37 mV typical input offset supports small threshold differences around precision references, while the wide supply rating gives design margin for industrial rails. The open-collector outputs are useful when several fault conditions must be combined, although external pull-up resistors and input protection are required.

🌡️

Thermistor and Resistive Sensor Conditioning

The LM2901DE4 can compare a thermistor divider or other resistive sensor against a reference voltage to create a simple hardware alarm or control signal. Its low input bias current of 3.5 nA reduces loading of high-impedance sensing networks, while the common-mode input range including ground supports sensors near the lower end of a single-supply range. The four-channel arrangement allows one package to monitor several temperature or condition thresholds. A precision reference, resistor-divider tolerances, and input filtering should be selected together because the comparator provides the decision function but does not remove reference or sensor errors.

🔌

Power-Supply Overvoltage and Undervoltage Detection

The LM2901DE4 can implement hardware protection windows around a regulated rail by comparing divided supply voltages against references. One channel may detect overvoltage and another undervoltage, with the open-collector outputs wired together through a shared pull-up to create a combined fault signal. The wide 38 V maximum supply rating provides headroom for 24 V industrial systems, while the 2 V to 30 V operating range supports lower-voltage rails. Designers should add input clamping and filtering for fast transients, and should calculate comparator response and propagation delay when the protection signal must act before downstream damage occurs.

🚗

Motor and Relay Control Logic

The LM2901DE4 is useful as a hardware decision stage in motor-control and relay systems where an analog current, voltage, or position signal must be converted to a logic command. The comparator can evaluate a control-loop signal against a reference and provide an open-collector output to a driver interface. The low supply current is helpful in low-power control electronics, and the four channels can monitor multiple conditions. Because an open-collector output can sink current rather than source it, it pairs naturally with relay-driver or transistor logic, but the external pull-up voltage and the driver's input requirements must remain compatible.

🔬

Test and Measurement Signal Qualification

The LM2901DE4 can qualify a measured signal in instrumentation systems by deciding whether a voltage is above or below a selected threshold. Such a decision can be routed to a test-set point, relay, or digital acquisition system, reducing the processing required from the measurement controller. The quad-channel structure allows several limits to be evaluated simultaneously, and the open-collector outputs can be combined for a pass-or-fail indication. For precision measurements, account for input offset, resistor matching, reference accuracy, temperature drift, and comparator propagation delay. Use short, guarded input routes and appropriate filtering to prevent high-impedance nodes from picking up noise.

What is the operating voltage range of LM2901DE4?
The LM2901DE4 operates from 2 V to 30 V for single-supply operation, and its maximum supply rating is 38 V. According to the Texas Instruments LM2901 datasheet and product information, the device also supports split-supply operation when the individual rail and input common-mode conditions are respected. The actual usable supply must also remain within the absolute maximum rating, with transient protection recommended for exposed industrial nodes.
How many comparators are in the LM2901DE4?
The LM2901DE4 contains four independent differential comparator channels in one 14-SOIC package. Each channel has its own non-inverting and inverting inputs and an open-collector output. According to the Texas Instruments LM2901 product page, the four-channel arrangement is suitable for multi-level threshold detection, window monitoring, and systems that need several independent analog-to-logic decisions without using four separate packages.
What is the input offset voltage of LM2901DE4?
The LM2901DE4 has a low input offset voltage of 0.37 mV in the manufacturer description for the LM2901B and LM2901 family. A low offset helps the comparator resolve small differences between its two inputs, which is important when comparing a sensor signal with a precision reference. The final threshold accuracy also depends on resistor tolerances, input bias current, temperature, and the particular datasheet limit used for the design.
Does LM2901DE4 have an open-collector output?
Yes. The LM2901DE4 uses an open-collector output on every comparator channel. An external pull-up resistor is required when the output must reach a defined logic-high voltage, and the pull-up can be shared when multiple outputs are intentionally combined in a wired-AND arrangement. The Texas Instruments datasheet states that the outputs are compatible with TTL, MOS, and CMOS logic when used with the appropriate pull-up network.
Where can I download the LM2901DE4 datasheet PDF?
The official Texas Instruments LM2901 product page is the best starting point for the LM2901DE4 datasheet, pin configuration, electrical characteristics, and ordering information. The manufacturer product information identifies the B-version as a drop-in replacement for the LM239, LM339, and LM2901 families. Use the TI documentation for design sign-off because third-party copies can reflect different revisions or omit package-specific ordering details.
What is the pinout of the LM2901DE4 14-SOIC package?
The LM2901DE4 uses a 14-pin SOIC with four differential comparator sections. The standard numbering places OUT1 on pin 1, IN1− on pin 2, IN1+ on pin 3, GND on pin 4, IN2+ on pin 5, IN2− on pin 6, OUT2 on pin 7, OUT3 on pin 8, IN3− on pin 9, IN3+ on pin 10, VCC on pin 11, IN4+ on pin 12, IN4− on pin 13, and OUT4 on pin 14. Confirm the final pin descriptions against the Texas Instruments datasheet before PCB release.
Is LM2901DE4 suitable for single 5 V supply designs?
Yes. The LM2901DE4 is suitable for a 5 V single-supply design because its specified operating supply range includes 5 V and its common-mode input range includes ground. Each open-collector output can be pulled up to 5 V when the load is compatible with the output transistor and pull-up resistor. Designers should still check the input common-mode limits at the actual signal levels and confirm the output pull-up current at the selected logic threshold.
Can LM2901DE4 replace LM2901D without PCB changes?
The LM2901D is a closely related 14-SOIC variant and is a practical candidate for pin-compatible substitution, but the exact ordering suffix, temperature rating, and electrical limits must be checked before production release. The Texas Instruments LM2901 family page identifies the B-version as a drop-in replacement for earlier LM239, LM339, and LM2901 versions. The replacement decision should confirm pinout, output type, supply range, offset voltage, response time, and package dimensions.
LM2901DE4 vs LM2901DRE4 - which version should I choose?
Choose the version whose temperature grade and ordering suffix match the production environment. LM2901DE4 and LM2901DRE4 are listed as 14-SOIC quad comparator variants, but their exact suffix, rating, and lifecycle details must be compared from the Texas Instruments product documentation. Both use the same family architecture and open-collector output concept; the key engineering checks are package, temperature range, common-mode limits, offset voltage, and qualification requirements.
What is the best drop-in replacement for LM2901DE4?
The best drop-in replacement is the LM2901D-family 14-SOIC variant whose pinout and electrical ratings match the target. LM2901D and LM2901DRE4 are the most relevant candidates identified for this family because they are listed as 14-SOIC versions, while LM2901M and LM2901N use a different package and are not direct PCB drop-ins. Verify the manufacturer datasheet, temperature grade, and required qualification before substituting any candidate.
When should I choose LM2901DE4 over a dual or single comparator?
Choose the LM2901DE4 when the design requires four independent threshold decisions and all channels share compatible supply and input conditions. A dual or single comparator may be preferable when only one or two channels are needed, when channel-specific supply levels are required, or when minimizing package cost is more important than integration. The LM2901DE4 reduces the number of packages and provides a common 14-SOIC footprint while retaining independent open-collector outputs.
How do I design the pull-up resistor for LM2901DE4 outputs?
Select the pull-up resistor from the required output-high current, permitted output-transistor dissipation, and desired logic rise time. A smaller resistor produces a faster rising edge but increases sink current and power loss; a larger resistor reduces loading but can slow the transition and increase susceptibility to noise. Use the Texas Instruments electrical characteristics and the connected logic input's current limits to calculate the final value, and account for capacitive load when evaluating speed.
How much supply current does LM2901DE4 consume?
The LM2901DE4 is specified at approximately 200 uA of supply current per comparator, or roughly 800 uA for four channels under the cited conditions. Actual consumption depends on the supply voltage, input states, output pull-up network, and device version. The manufacturer datasheet is the controlling reference for test conditions and maximum supply current, especially when designing low-power battery or sensor-powered systems.
Is LM2901DE4 still active for industrial designs?
The LM2901 is identified by Texas Instruments as an active general-purpose family, and the LM2901DE4 is currently offered in a 14-SOIC package. Its -40 °C to +125 °C operating range and wide supply tolerance make it suitable for many industrial applications. For a new production design, verify the exact orderable status, temperature suffix, lifecycle, and current qualification documents with the manufacturer before release.
Where can I buy LM2901DE4 and what is its price?
Use the Request a Quote form on this page to request LM2901DE4 availability, current commercial terms, and a quotation for the exact 14-SOIC ordering suffix. The form is the appropriate purchasing channel for this product because commercial terms and inventory can change. The manufacturer product page and authorized distribution listings can also be used to confirm technical documentation, but the quote request on this page provides the direct procurement path.
What is the lead time for LM2901DE4?
The current lead time for LM2901DE4 should be requested through the Request a Quote form on this page for the exact package, quantity, and delivery destination. Lead time can depend on order volume, manufacturing status, allocation, and packaging configuration, so a generic answer would not be reliable. The Texas Instruments product page should be used to confirm the currently offered orderable part before committing the supply plan.

بيانات مرجعية هندسية لـ LM2901DE4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the LM2901DE4 for a new design that needs four independent threshold decisions, a single or split supply within the family limits, and open-collector outputs. It is particularly useful when multiple fault conditions can share a pull-up node and when a conventional 14-SOIC footprint simplifies PCB assembly. Choose LM2901D when its specific suffix and qualification requirements better match an existing design, or when supply continuity favors that ordering code. Choose LM2901DRE4 or LM2901DG4 only after checking the exact temperature, rating, and lifecycle details. Avoid LM2901M or LM2901N as direct PCB replacements when the original board uses LM2901DE4 because those variants use a different package. In all cases, verify the complete pinout, input common-mode limits, output pull-up design, and propagation delay before releasing a replacement to production.

المقارنة مع البدائل

المعامل هذا المنتج LM2901D LM2901DRE4 LM2901DG4 LM2901DR
Package 14-SOIC 14-SOIC 14-SOIC 14-SOIC 14-SOIC
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Comparator Configuration Quad differential comparator Quad differential comparator Quad differential comparator Quad differential comparator Quad differential comparator
Output Type Open-collector Open-collector Open-collector Open-collector Open-collector
Supply Voltage Range 2 V to 30 V 2 V to 30 V 2 V to 30 V 2 V to 30 V 2 V to 30 V
Maximum Supply Rating 38 V 38 V 38 V 38 V 38 V

أبرز الفروقات

  • Four independent comparator channels in one package (مقابلLM2901D)
  • Wide supply and common-mode operating range (مقابلLM2901DRE4)
  • Low input offset suitable for small threshold differences (مقابلLM2901DG4)
  • Open-collector outputs support wired fault signaling (مقابلLM2901DR)

ملاحظات التصميم

Do not treat the open-collector output as a push-pull logic output. Each output needs an external pull-up resistor when a defined high level is required. Select the resistor using the input current of the receiving logic, the output transistor's allowable sink current, the desired rise time, and capacitive loading. When several channels drive one node, confirm that their individual output states and maximum sink currents are compatible with the shared pull-up network.

Place the pull-up resistor close to the comparator output or the receiving logic input, and keep the route short to reduce susceptibility to capacitive coupling and switching noise. Route differential inputs away from the supply return path of motors, relays, and power converters. If the input source is high impedance, use a nearby ground reference and consider small input-protection components, while checking that added capacitance does not impair response time.

Estimated: with a 12 V supply and a 5 V output pull-up, the pull-up resistor dissipates power whenever the comparator output is low. Use P = (12 V - Vout_low)^2 / R for the worst-case resistor dissipation and P = Vout_low times the pull-up current for the output transistor. Select R and the package thermal allowance together rather than treating the open-collector output as a zero-loss logic driver.

The 0.37 mV typical offset is only one contributor to threshold accuracy. Resistor tolerance, reference noise, temperature drift, input bias current, and propagation delay can dominate the actual error. For precision sensing, use a low-noise reference, matched divider resistors, short input traces, and an RC filter with a time constant short compared with the required response time. Do not add excessive capacitance where fast fault detection is important.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The supplied product information confirms the LM2901 family, 14-SOIC package, electrical headline specifications, and open-collector output architecture. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the listed source snippets and require confirmation from the current manufacturer documentation or a declaration.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LM2901DE4 datasheet LM2901DE4 pinout LM2901DE4 datasheet pdf LM2901DE4 equivalent LM2901DE4 replacement LM2901DE4 cross reference LM2901DE4 vs LM2901D LM2901DE4 14-SOIC LM2901DE4 open collector comparator LM2901DE4 price LM2901DE4 stock Texas Instruments LM2901DE4 LM2901DE4 voltage threshold circuit LM2901DE4 output pull-up resistor LM2901DE4 supply voltage

المكونات والمصطلحات ذات الصلة

Texas Instruments LM2901DE4 LM2901D LM2901DRE4 LM2901DG4 LM2901DR quad differential comparator comparator interface IC analog integrated circuit open-collector output TTL MOS logic CMOS logic 14-SOIC surface-mount package semiconductor input offset voltage input bias current common-mode input voltage supply voltage wired-AND battery monitoring industrial threshold detection
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر