LM2901DE4 - Quad Open-Collector Comparator, 2-30V | Texas Instruments
부품 번호: LM2901DE4 ✓ 활성LM2901DE4 개요
A differential comparator is an analog integrated circuit that compares two voltage inputs and changes its output state according to their relative voltage. The LM2901 belongs to the comparator category within the broader interface IC hierarchy, where analog front-end decision-making is followed by digital logic, control, or measurement. Unlike an operational amplifier, the comparator is intended primarily for threshold crossing and does not provide linear amplification. The LM2901 family combines four channels in one package, allowing a compact design when multiple independent decisions are needed. Its common-mode input range includes ground, making it useful in systems powered from a single positive rail where the signal being compared can approach 0 V.
Key features include a maximum supply rating of 38 V, a low input offset voltage of 0.37 mV, an input bias current of 3.5 nA, and low supply-current consumption of approximately 200 uA per comparator. The open-collector output structure is compatible with TTL, MOS, and CMOS logic when the appropriate pull-up is used. The comparator also supports a faster response time than many older standard quad comparators. Because all four channels share the same supply pins, the device is most appropriate when the compared signals operate within the same supply system. The 14-SOIC package provides a conventional surface-mount footprint and broad compatibility with industrial control-board layouts.
The internal architecture uses four differential comparator channels referenced to the common ground and supply rails. The input stage is designed for low offset and low bias current, reducing errors when small signal differences must be detected. The open-collector transistor remains off when the comparator output is high impedance and conducts when the output is driven low. The external pull-up resistor determines the high-state voltage and limits the current through the output transistor. The maximum differential input voltage and common-mode voltage limits must be respected during startup, fault conditions, and signal transients. The manufacturer datasheet is the authoritative source for absolute maximum ratings, electrical limits, timing characteristics, and the complete pin configuration.
Typical uses include monitoring a battery or power rail, detecting an overvoltage or undervoltage condition, comparing a thermistor or divider output with a reference, and providing a fault flag in industrial equipment. The four channels can also implement independent window comparisons when suitable resistor networks are used. Open-collector outputs are particularly useful when multiple comparators must signal one system event through a common pull-up node. In motor-control, power-supply, and instrumentation circuits, the device can provide a hardware threshold decision before a controller reacts, reducing the processing burden on the controller.
The principal design consideration is the pull-up network on every open-collector output. Select the resistor to balance rise time against output-transistor dissipation and required logic current. Keep comparator inputs away from noisy power-switching nodes, use a stable reference for precision thresholds, and account for input common-mode limits. When replacing another quad comparator, verify the complete pinout, output architecture, supply range, input offset, response time, and temperature rating before production use. The LM2901DE4 is a standard general-purpose choice for designs requiring four channels, wide supply tolerance, and flexible open-collector interfacing.
드롭인 대체품: LM2901DE4 — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: LM2901DE4 (동일 폼 팩터 및 풋프린트) — 차이점: Logic Compatibility, Differential Input Voltage Range, Package, Comparator Type, Supply Voltage Range.
LM2901D
✅ 드롭인가격 문의
데이터시트 보기 →LM2901DRE4
✅ 드롭인📋 참조 대체품 (카탈로그에 없음)
LM2901DG4
✅ 드롭인가격 문의
데이터시트 보기 →LM2901DR
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2901DRE4
✅ 드롭인 ⚠️ 사양 미검증📋 참조 대체품 (카탈로그에 없음)
LM2901DE4 최대 정격 & 전기적 특성
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| 출력 유형 | Open-collector |
| Supply Voltage Range | 2 V to 30 V |
| Maximum Supply Rating | 38 V |
| Input Offset Voltage | 0.37 mV typical |
| Input Bias Current | 3.5 nA |
| 공급 전류 | 200 uA per comparator |
| Common-Mode Input Range | Includes ground |
| Differential Input Voltage Range | ±38 V |
| 동작 온도 범위 | -40 °C to +125 °C |
| 패키지 | 14-SOIC, 0.154 inch width, 3.90 mm width |
| 실장 유형 | Surface mount |
| Logic Compatibility | TTL, MOS, and CMOS compatible with pull-up |
| ESD Rating HBM | 2 kV |
| 출력 구성 | Wired-AND capable with external pull-up |
LM2901DE4 핀 구성
| 핀 1 | OUT1 — Comparator 1 open-collector output |
| 핀 2 | IN1- — Comparator 1 inverting input |
| 핀 3 | IN1+ — Comparator 1 non-inverting input |
| 핀 4 | GND — Ground |
| 핀 5 | IN2+ — Comparator 2 non-inverting input |
| 핀 6 | IN2- — Comparator 2 inverting input |
| 핀 7 | OUT2 — Comparator 2 open-collector output |
| 핀 8 | OUT3 — Comparator 3 open-collector output |
| 핀 9 | IN3- — Comparator 3 inverting input |
| 핀 10 | IN3+ — Comparator 3 non-inverting input |
| 핀 11 | VCC — Positive supply |
| 핀 12 | IN4+ — Comparator 4 non-inverting input |
| 핀 13 | IN4- — Comparator 4 inverting input |
| 핀 14 | OUT4 — Comparator 4 open-collector output |
일반적인 애플리케이션
LM2901DE4 적합 용도: 6 애플리케이션s: Battery Voltage Monitoring, Industrial Threshold Detection, Thermistor and Resistive Sensor Conditioning, Power-Supply Overvoltage and Undervoltage Detection, Motor and Relay Control Logic, Test and Measurement Signal Qualification.
Battery Voltage Monitoring
The LM2901DE4 is suitable for monitoring a battery or power rail when the system requires a hardware threshold decision rather than relying only on firmware. Place one comparator channel across a resistor-divider output and a stable reference, then use the open-collector output to assert a fault signal when the monitored voltage crosses its limit. The 2 V to 30 V operating supply range supports many single-rail systems, while the low 200 uA per-comparator supply current helps preserve battery life. Because the output is open collector, a pull-up resistor can connect the fault indication to a supervisor, microcontroller input, or another comparator channel.
추천
Industrial Threshold Detection
Use the LM2901DE4 for independent threshold detection in industrial control equipment, such as detecting an out-of-range control signal or converting an analog sensor condition into a logic event. Its four differential channels provide separate decisions while sharing a common supply and ground in one 14-SOIC package. The 0.37 mV typical input offset supports small threshold differences around precision references, while the wide supply rating gives design margin for industrial rails. The open-collector outputs are useful when several fault conditions must be combined, although external pull-up resistors and input protection are required.
추천
Thermistor and Resistive Sensor Conditioning
The LM2901DE4 can compare a thermistor divider or other resistive sensor against a reference voltage to create a simple hardware alarm or control signal. Its low input bias current of 3.5 nA reduces loading of high-impedance sensing networks, while the common-mode input range including ground supports sensors near the lower end of a single-supply range. The four-channel arrangement allows one package to monitor several temperature or condition thresholds. A precision reference, resistor-divider tolerances, and input filtering should be selected together because the comparator provides the decision function but does not remove reference or sensor errors.
추천
Power-Supply Overvoltage and Undervoltage Detection
The LM2901DE4 can implement hardware protection windows around a regulated rail by comparing divided supply voltages against references. One channel may detect overvoltage and another undervoltage, with the open-collector outputs wired together through a shared pull-up to create a combined fault signal. The wide 38 V maximum supply rating provides headroom for 24 V industrial systems, while the 2 V to 30 V operating range supports lower-voltage rails. Designers should add input clamping and filtering for fast transients, and should calculate comparator response and propagation delay when the protection signal must act before downstream damage occurs.
추천
Motor and Relay Control Logic
The LM2901DE4 is useful as a hardware decision stage in motor-control and relay systems where an analog current, voltage, or position signal must be converted to a logic command. The comparator can evaluate a control-loop signal against a reference and provide an open-collector output to a driver interface. The low supply current is helpful in low-power control electronics, and the four channels can monitor multiple conditions. Because an open-collector output can sink current rather than source it, it pairs naturally with relay-driver or transistor logic, but the external pull-up voltage and the driver's input requirements must remain compatible.
추천
Test and Measurement Signal Qualification
The LM2901DE4 can qualify a measured signal in instrumentation systems by deciding whether a voltage is above or below a selected threshold. Such a decision can be routed to a test-set point, relay, or digital acquisition system, reducing the processing required from the measurement controller. The quad-channel structure allows several limits to be evaluated simultaneously, and the open-collector outputs can be combined for a pass-or-fail indication. For precision measurements, account for input offset, resistor matching, reference accuracy, temperature drift, and comparator propagation delay. Use short, guarded input routes and appropriate filtering to prevent high-impedance nodes from picking up noise.
추천
추천 제품 요약
엔지니어링 참조 데이터: LM2901DE4 — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | LM2901D | LM2901DRE4 | LM2901DG4 | LM2901DR |
|---|---|---|---|---|---|
| Package | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC | 14-SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Configuration | Quad differential comparator | Quad differential comparator | Quad differential comparator | Quad differential comparator | Quad differential comparator |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Supply Voltage Range | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V | 2 V to 30 V |
| Maximum Supply Rating | 38 V | 38 V | 38 V | 38 V | 38 V |
주요 차별점
- Four independent comparator channels in one package (vs LM2901D)
- Wide supply and common-mode operating range (vs LM2901DRE4)
- Low input offset suitable for small threshold differences (vs LM2901DG4)
- Open-collector outputs support wired fault signaling (vs LM2901DR)
설계 노트
Do not treat the open-collector output as a push-pull logic output. Each output needs an external pull-up resistor when a defined high level is required. Select the resistor using the input current of the receiving logic, the output transistor's allowable sink current, the desired rise time, and capacitive loading. When several channels drive one node, confirm that their individual output states and maximum sink currents are compatible with the shared pull-up network.
Place the pull-up resistor close to the comparator output or the receiving logic input, and keep the route short to reduce susceptibility to capacitive coupling and switching noise. Route differential inputs away from the supply return path of motors, relays, and power converters. If the input source is high impedance, use a nearby ground reference and consider small input-protection components, while checking that added capacitance does not impair response time.
Estimated: with a 12 V supply and a 5 V output pull-up, the pull-up resistor dissipates power whenever the comparator output is low. Use P = (12 V - Vout_low)^2 / R for the worst-case resistor dissipation and P = Vout_low times the pull-up current for the output transistor. Select R and the package thermal allowance together rather than treating the open-collector output as a zero-loss logic driver.
The 0.37 mV typical offset is only one contributor to threshold accuracy. Resistor tolerance, reference noise, temperature drift, input bias current, and propagation delay can dominate the actual error. For precision sensing, use a low-noise reference, matched divider resistors, short input traces, and an RC filter with a time constant short compared with the required response time. Do not add excessive capacitance where fast fault detection is important.
규정 준수 정보
The supplied product information confirms the LM2901 family, 14-SOIC package, electrical headline specifications, and open-collector output architecture. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established by the listed source snippets and require confirmation from the current manufacturer documentation or a declaration.