Texas Instruments

LM2903BIPWR - Dual 36V Comparator | Texas Instruments

MPN: LM2903BIPWR ✓ نشط
2 V to 36 V Vdss 3.5 nA Id 8-pin TSSOP (PW) Package
الحد الأدنى للطلب: 1 |

LM2903BIPWR نظرة عامة

The Texas Instruments LM2903BIPWR is a dual industrial-grade comparator with a 2 V to 36 V supply range, 1 µs response time, and open-collector outputs in an 8-pin TSSOP package. Each channel provides an independent comparison function, with input offset voltage as low as 0.37 mV and input bias current as low as 3.5 nA. The device is designed for robust threshold detection, industrial signal conditioning, and systems powered from higher-voltage rails.

A voltage comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903B belongs to the comparator hierarchy, where it functions as a general-purpose comparator, analog signal interface, and power-management building block. Its two channels can monitor independent sensors or participate in window-detection and overvoltage-protection circuits. Open-collector outputs also make wired-AND behavior possible when multiple comparators share a pull-up resistor.

The B-version improvements include a maximum supply rating of 38 V, a 2 kV human-body-model ESD rating, low input offset, low input bias current, and supply current of 200 µA per comparator. The 1 µs response time supports faster decision-making than legacy comparators, while the rail-to-rail input characteristic permits operation from the ground rail to the positive supply rail. The industrial temperature range covers applications from -40 °C to +125 °C.

Each output uses an open-drain transistor rather than a push-pull output stage. This architecture provides flexible voltage-level compatibility because an external pull-up resistor determines the output voltage. It also permits several outputs to be connected together when the resulting wired-AND behavior is intentional. A pull-up resistor is required even when only one output is used; without it, the output cannot rise to a valid high state.

Typical uses include industrial sensor interfaces, battery threshold detection, motor and actuator protection, window comparators, relay-control logic, and power-supply monitoring. The 36 V operating range is useful in industrial systems where the comparator may directly observe a protected signal node. The low 200 µA per-comparator supply current also makes the device suitable for low-power monitoring when the signal source can be brought close to the supply rail.

For reliable layout, route each comparison input directly to its device pin and keep feedback or output loops away from the input traces. Place the output pull-up resistor close to the open-collector output, and use a local supply bypass capacitor where the power rail can produce disturbance. Account for input common-mode voltage and output leakage when designing the system threshold.

This page combines the Texas Instruments ordering information, device specifications, package details, pin assignments, sourcing workflow, and practical replacement guidance to support faster component selection and PCB design. Use the manufacturer datasheet for the complete electrical characteristics, timing definitions, and application guidance.

بدائل مباشرة لـ LM2903BIPWR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع LM2903BIPWR (نفس عامل الشكل والبصمة) — يختلف في Comparator Type, ESD Rating, Input Bias Current, Input Offset Voltage, Package.

Texas Instruments
Comparator Type: Dual differential comparator
ESD Rating: 2kV HBM
Input Bias Current: 3.5nA maximum
قارن مع LM2903BIPWR →
Texas Instruments
Comparator Type: Dual differential comparator
قارن مع LM2903BIPWR →

LM2903PWR

✅ بديل مباشر
Texas Instruments
📦 8-pin TSSOP (PW)
Dual differential comparator · 2 channels · Open-collector · Rail-to-rail · ±18V / 36V total · Up to 38V · 0.37mV maximum · 3.5nA maximum

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM2903BIPWR الحدود القصوى والخصائص الكهربائية

Comparator Type Dual general-purpose voltage comparator
Number of Channels 2 channels
Supply Voltage Range 2 V to 36 V
Absolute Maximum Supply Voltage 38 V
Input Offset Voltage 0.37 mV
Input Bias Current 3.5 nA
تيار التغذية 200 µA per comparator
Response Time 1 µs
نوع الخرج Open-collector
Input Common-Mode Range Rail-to-rail
ESD Rating 2 kV HBM
نطاق درجة حرارة التشغيل -40 °C to +125 °C
العلبة 8-pin TSSOP (PW)
نوع التركيب Surface mount

تكوين أطراف LM2903BIPWR

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
دبوس 1 OUT1 — Open-collector output for comparator channel 1
دبوس 2 IN1- — Inverting input for comparator channel 1
دبوس 3 IN1+ — Non-inverting input for comparator channel 1
دبوس 4 GND — Ground connection
دبوس 5 IN2+ — Non-inverting input for comparator channel 2
دبوس 6 IN2- — Inverting input for comparator channel 2
دبوس 7 OUT2 — Open-collector output for comparator channel 2
دبوس 8 VCC — Positive supply connection

التطبيقات النموذجية

LM2903BIPWR مناسب لـ 6 التطبيقs: 24 V Industrial Sensor Threshold Detection, Battery Pack Overvoltage Protection, Power-Supply Overvoltage Detection, Motor and Actuator Limit Detection, Window Comparator and Fault Logic, TTL and CMOS Logic Interfacing.

🏭

24 V Industrial Sensor Threshold Detection

The LM2903BIPWR fits 24 V industrial sensor interfaces because its 2 V to 36 V operating range accommodates protected sensor nodes while its 0.37 mV input offset helps distinguish closely spaced trip points. Place one channel across a divided sensor signal and the other at a configurable upper threshold. The open-collector output can directly pull down an isolated digital input or PLC input when the threshold is exceeded, with an external pull-up defining the logic voltage. The 200 µA per-comparator supply current limits continuous overhead, while the 1 µs response time reduces detection delay.

⚡

Battery Pack Overvoltage Protection

The LM2903BIPWR is useful for battery-pack protection because its rail-to-rail inputs can monitor a divided pack voltage and its two channels can supervise upper and lower boundaries. Use resistor dividers to bring the cell stack within the comparator input range, then connect the open-collector outputs to a protection latch or disconnect driver. The 200 µA current per comparator limits divider and monitoring overhead, while the 1 µs response supports rapid fault detection. The 36 V operating capability is valuable for industrial battery systems, although the external divider must maintain suitable fault margins.

⚡

Power-Supply Overvoltage Detection

The LM2903BIPWR can supervise a rectified or regulated power rail when its monitored voltage is scaled to remain within the 2 V to 36 V comparator range. The two independent channels support separate high and low limits, allowing a compact window comparator without using a dedicated window-comparator IC. An open-collector output can drive a fault latch, relay, or optocoupler through an appropriate pull-up and interface network. Its low 0.37 mV offset supports fine threshold control after amplification, and its 1 µs response time helps minimize the interval between a rail excursion and the protective action.

🚗

Motor and Actuator Limit Detection

The LM2903BIPWR suits motor and actuator limit detection where two independent thresholds monitor position, current, or feedback voltages. Its 1 µs response time helps minimize propagation through the comparison stage, while the open-collector output can pull a protection input or gate-driver interface into an active state. The wide 36 V operating range accommodates industrial control rails, and the 200 µA per-comparator current is useful in power-conserving supervisory designs. Input common-mode limits and transient protection remain important when connected to motor-node signals because the comparator package alone does not provide surge protection.

🧩

Window Comparator and Fault Logic

The LM2903BIPWR's two independent channels can implement a window detector, with one comparator establishing the lower limit and the other establishing the upper limit. Their open-collector outputs can share a pull-up when wired-AND behavior is required, allowing the combined output to indicate whether a monitored signal is outside its acceptable range. The B-version's 3.5 nA input bias current minimizes error in high-impedance divider networks, and its 0.37 mV offset improves threshold precision. Design the pull-up and downstream logic so the wired output polarity matches the intended fault convention.

🖥️

TTL and CMOS Logic Interfacing

The LM2903BIPWR can interface industrial sensors with TTL or CMOS logic because its open-collector output requires an external pull-up that can be connected to the destination logic rail. This allows the comparator output voltage to be defined independently of its 2 V to 36 V supply range. The 1 µs response time supports moderately fast threshold events, while the 200 µA per-comparator supply current helps maintain low system overhead. Use a pull-up value that balances input current, switching speed, power dissipation, and the number of outputs connected to the same node.

What is the operating voltage of LM2903BIPWR?
The LM2903BIPWR operates from 2 V to 36 V, with an absolute maximum supply rating of 38 V. According to the Texas Instruments LM2903B product information and manufacturer datasheet, this wide operating range makes the dual comparator suitable for industrial signal-threshold detection where the monitored node can vary substantially. Each channel operates independently, although both channels share the same supply pins.
What are the key specifications of LM2903BIPWR that engineers should know?
The LM2903BIPWR is a dual, open-collector comparator with a 2 V to 36 V operating range, 0.37 mV input offset voltage, 3.5 nA input bias current, 200 µA supply current per comparator, and 1 µs response time. Texas Instruments describes it as an industrial-grade device with rail-to-rail inputs, a 2 kV HBM ESD rating, and an operating temperature range of -40 °C to +125 °C.
Where can I download the LM2903BIPWR datasheet PDF?
The LM2903BIPWR datasheet can be downloaded from the Texas Instruments LM2903B product page at https://www.ti.com/product/LM2903B. The ordering-information page for the exact LM2903BIPWR suffix is at https://www.ti.com/product/LM2903B/part-details/LM2903BIPWR. These manufacturer pages provide the device description, ordering information, electrical characteristics, pinout, and supporting application information.
Where can I find the LM2903BIPWR pinout?
The LM2903BIPWR pinout is defined for its 8-pin TSSOP package, with pins 1 and 7 assigned to the two open-collector outputs, pins 2 and 6 to inverting inputs, pins 3 and 5 to non-inverting inputs, pin 4 to ground, and pin 8 to the positive supply. Use the pin-description table in the Texas Instruments manufacturer datasheet when assigning PCB tracks.
Is LM2903BIPWR the same as LM2903PWR?
The LM2903BIPWR and LM2903PWR use the same 8-pin TSSOP package and provide the same dual open-collector comparator function, but the LM2903BIPWR is the upgraded B-version. Texas Instruments identifies the B version as a drop-in replacement for LM293, LM393, and LM2903 A and V versions, with improved offset, bias current, supply current, response time, voltage capability, and ESD performance.
What is the best drop-in replacement for LM2903BIPWR?
The LM2903PWR is the closest same-package drop-in alternative identified for the LM2903BIPWR because both are dual open-collector comparators in an 8-pin TSSOP arrangement. The B-version LM2903BIPWR provides the improved 0.37 mV offset, 3.5 nA bias current, 200 µA per-comparator supply current, and 1 µs response time, so retain the B version when those upgraded specifications matter.
What can replace LM2903BIPWR?
The LM2903PWR can replace the LM2903BIPWR on the same 8-TSSOP footprint when its legacy electrical ratings satisfy the design. The LM2903BIPWR is preferable when the application benefits from the B-version's 0.37 mV offset, 3.5 nA input bias current, 200 µA supply current per comparator, and 1 µs response time. Confirm every operating limit against the manufacturer datasheet before substitution.
Is the STMicroelectronics LM2903B a drop-in replacement for LM2903BIPWR?
The STMicroelectronics LM2903B is a functional family alternative because it also contains two independent low-power comparators for single-supply operation. However, the ordering suffix and package must be confirmed to match the LM2903BIPWR's 8-pin TSSOP footprint before treating it as a direct drop-in replacement. The Texas Instruments LM2903BIPWR remains the reference choice for its documented TSSOP ordering configuration.
LM2903BIPWR vs LM2903PWR — which is better for a 24 V industrial sensor?
The LM2903BIPWR is generally better for a new 24 V industrial sensor interface because it is the upgraded B-version and supports operation from 2 V to 36 V. The LM2903PWR shares the 8-pin TSSOP footprint and open-collector architecture, but the LM2903BIPWR adds improved offset voltage, bias current, supply current, response time, maximum voltage capability, and ESD performance.
When should I choose LM2903BIPWR over LM2903PWR?
Choose the LM2903BIPWR when low offset, low input bias current, low supply consumption, fast response, or the wider 36 V operating range is important. Its documented improvements include 0.37 mV input offset, 3.5 nA input bias current, 200 µA per comparator, and 1 µs response time. Choose the LM2903PWR only when its older ratings meet the design and board reuse makes it the lower-complexity option.
Is LM2903BIPWR suitable for battery-powered monitoring?
The LM2903BIPWR can suit battery-powered monitoring when the monitored signals operate within its 2 V to 36 V range and low quiescent consumption is important. Its supply current is 200 µA per comparator, while the open-collector output can be pulled up to a low logic voltage. Input leakage, the pull-up resistor, and the battery voltage should be included in the total power budget.
How do I use the open-collector outputs of LM2903BIPWR?
Each LM2903BIPWR output requires an external pull-up resistor because the output transistor can pull the node low but cannot actively drive it high. Connect the pull-up to the desired logic supply and use a suitable resistor value for the required speed and current. Multiple open-collector outputs may share one pull-up to implement wired-AND behavior, provided the resulting logic is intentional.
What thermal and layout considerations apply to LM2903BIPWR?
Keep the LM2903BIPWR's supply and ground connections short, place the bypass capacitor close to pin 8 and pin 4, and route the high-impedance input traces away from the output and pull-up network. The device dissipates little power in normal comparator operation because its supply current is 200 µA per comparator, but adequate copper area remains important for stable supply behavior and temperature rise.
Is LM2903BIPWR suitable for automotive applications?
The LM2903BIPWR is an industrial-grade comparator with a -40 °C to +125 °C operating temperature range, but that temperature rating alone does not establish automotive qualification. The exact LM2903BIPWR ordering option should not be treated as AEC-Q100 qualified unless the manufacturer marks it accordingly. Use a specifically automotive-qualified comparator orderable in the required package for vehicle designs.
Where to buy LM2903BIPWR online and what is its lead time?
Use the Request a Quote form on this page to request LM2903BIPWR availability, current lead time, and order quantities from XAIPART. The device is an 8-pin TSSOP part offered by Texas Instruments, and a current distributor listing identifies it as in stock. The manufacturer ordering page should be used to confirm the exact suffix, package, and qualification status.
What is the price of LM2903BIPWR?
The current commercial price for LM2903BIPWR is shown through the Request a Quote form on this page because pricing and availability can change with quantity, inventory, and order timing. Submit the required quantity and target package information with the request. The manufacturer identifies the exact device as an 8-pin TSSOP comparator for industrial-grade applications.
Is LM2903BIPWR in stock?
LM2903BIPWR is shown as in stock in a current distributor listing, but transaction-ready inventory should be confirmed through the Request a Quote form on this page. The form allows you to request the current quantity, lead time, and order confirmation for the exact LM2903BIPWR ordering code. This avoids relying on a static listing status that may change.

بيانات مرجعية هندسية لـ LM2903BIPWR — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LM2903BIPWR for new industrial designs that benefit from the B-version's 2 V to 36 V operating range, 0.37 mV input offset, 3.5 nA input bias current, 200 µA per-comparator supply current, and 1 µs response time. It is particularly suitable for 24 V sensing, battery protection, window comparison, and threshold detection where an external pull-up can define the logic level. Choose LM2903PWR when an existing 8-pin TSSOP design uses the legacy device, its lower 30 V maximum rating is acceptable, and reducing redesign risk is more important than obtaining the improved B-version specifications. Do not select a functional equivalent solely by its family name; confirm the exact package suffix, pin mapping, common-mode range, output type, temperature grade, and qualification requirements before approving a replacement.

المقارنة مع البدائل

المعامل هذا المنتج LM2903PWR
Brand Texas Instruments Texas Instruments
Package 8-pin TSSOP (PW) 8-pin TSSOP (PW) - same
Comparator Configuration Dual Dual
Maximum Supply Voltage 38 V 30 V
Supply Current 200 µA per comparator 400 µA per comparator
Output Type Open-collector Open-collector

أبرز الفروقات

  • Higher supply-voltage capability (مقابلLM2903PWR)
  • Lower supply consumption (مقابلLM2903PWR)
  • Improved B-version signal performance (مقابلLM2903PWR)

ملاحظات التصميم

Route the two non-inverting and two inverting inputs as short, guarded traces, keeping them away from the open-collector outputs and pull-up resistors. High-impedance divider nodes can couple output-edge noise into the reference input and cause false switching. Use a ground reference that returns cleanly to pin 4, and place the supply bypass capacitor close to pins 8 and 4.

Every open-collector output needs an external pull-up resistor. The device can pull the output low, but it cannot actively drive the node high. Select the pull-up supply carefully so it remains within the destination logic's voltage range. When several outputs share one pull-up, verify that the wired-AND polarity produces the intended fault indication and that the combined sink current remains within rating.

Keep the supply voltage between 2 V and 36 V during normal operation and observe the 38 V absolute maximum rating only as a stress limit. The B version's 200 µA supply current per comparator reduces continuous overhead, but divider resistance and pull-up values can dominate total power. Choose the pull-up no larger than necessary for the required switching speed and destination input capacitance.

Do not substitute the LM2903BIPWR solely by comparator function. The replacement must use the same 8-pin TSSOP pin arrangement and meet the required input common-mode, output leakage, supply-voltage, response-time, and temperature limits. The legacy LM2903PWR has the same package and output architecture, but its lower supply-current capability and lower maximum supply rating require circuit-level verification.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The device is described by Texas Instruments as an industrial-grade dual comparator. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact LM2903BIPWR ordering code should be confirmed on the manufacturer product and ordering pages.

تم التحقق من البيانات في: 2026-11-17 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

LM2903BIPWR datasheet LM2903BIPWR pinout LM2903BIPWR datasheet pdf LM2903BIPWR equivalent LM2903BIPWR replacement LM2903BIPWR vs LM2903PWR LM2903BIPWR 8-TSSOP footprint Texas Instruments LM2903BIPWR LM2903BIPWR 36V comparator LM2903BIPWR industrial sensor LM2903BIPWR price LM2903BIPWR stock

المكونات والمصطلحات ذات الصلة

Texas Instruments LM2903BIPWR LM2903PWR LM2903B STMicroelectronics 3PEAK voltage comparator dual comparator general-purpose comparator analog comparator IC semiconductor open-collector output open-drain output rail-to-rail input input offset voltage input bias current supply current response time wired-AND logic TSSOP-8 TSSOP package family surface-mount package industrial temperature grade ESD protection 24 V industrial control
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر