LM2903BIPWR - Dual 36V Comparator | Texas Instruments
Référence : LM2903BIPWR ✓ ActifLM2903BIPWR Présentation
A voltage comparator is a signal-conditioning integrated circuit that compares two input voltages and changes its output state according to their relationship. The LM2903B belongs to the comparator hierarchy, where it functions as a general-purpose comparator, analog signal interface, and power-management building block. Its two channels can monitor independent sensors or participate in window-detection and overvoltage-protection circuits. Open-collector outputs also make wired-AND behavior possible when multiple comparators share a pull-up resistor.
The B-version improvements include a maximum supply rating of 38 V, a 2 kV human-body-model ESD rating, low input offset, low input bias current, and supply current of 200 µA per comparator. The 1 µs response time supports faster decision-making than legacy comparators, while the rail-to-rail input characteristic permits operation from the ground rail to the positive supply rail. The industrial temperature range covers applications from -40 °C to +125 °C.
Each output uses an open-drain transistor rather than a push-pull output stage. This architecture provides flexible voltage-level compatibility because an external pull-up resistor determines the output voltage. It also permits several outputs to be connected together when the resulting wired-AND behavior is intentional. A pull-up resistor is required even when only one output is used; without it, the output cannot rise to a valid high state.
Typical uses include industrial sensor interfaces, battery threshold detection, motor and actuator protection, window comparators, relay-control logic, and power-supply monitoring. The 36 V operating range is useful in industrial systems where the comparator may directly observe a protected signal node. The low 200 µA per-comparator supply current also makes the device suitable for low-power monitoring when the signal source can be brought close to the supply rail.
For reliable layout, route each comparison input directly to its device pin and keep feedback or output loops away from the input traces. Place the output pull-up resistor close to the open-collector output, and use a local supply bypass capacitor where the power rail can produce disturbance. Account for input common-mode voltage and output leakage when designing the system threshold.
This page combines the Texas Instruments ordering information, device specifications, package details, pin assignments, sourcing workflow, and practical replacement guidance to support faster component selection and PCB design. Use the manufacturer datasheet for the complete electrical characteristics, timing definitions, and application guidance.
Alternatives de remplacement direct pour LM2903BIPWR — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec LM2903BIPWR (même facteur de forme et même empreinte) — différant par Comparator Type, ESD Rating, Input Bias Current, Input Offset Voltage, Package.
LM2903PWR
✅ Remplacement directContactez-nous pour le prix
Voir la fiche technique →LM2903BIPWR Valeurs maximales et caractéristiques électriques
| Comparator Type | Dual general-purpose voltage comparator |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2 V to 36 V |
| Absolute Maximum Supply Voltage | 38 V |
| Input Offset Voltage | 0.37 mV |
| Input Bias Current | 3.5 nA |
| Courant d'alimentation | 200 µA per comparator |
| Response Time | 1 µs |
| Type de sortie | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| ESD Rating | 2 kV HBM |
| Plage de température de fonctionnement | -40 °C to +125 °C |
| Boîtier | 8-pin TSSOP (PW) |
| Type de montage | Surface mount |
Configuration des broches de LM2903BIPWR
| Broche 1 | OUT1 — Open-collector output for comparator channel 1 |
| Broche 2 | IN1- — Inverting input for comparator channel 1 |
| Broche 3 | IN1+ — Non-inverting input for comparator channel 1 |
| Broche 4 | GND — Ground connection |
| Broche 5 | IN2+ — Non-inverting input for comparator channel 2 |
| Broche 6 | IN2- — Inverting input for comparator channel 2 |
| Broche 7 | OUT2 — Open-collector output for comparator channel 2 |
| Broche 8 | VCC — Positive supply connection |
Applications typiques
LM2903BIPWR convient pour 6 applications: 24 V Industrial Sensor Threshold Detection, Battery Pack Overvoltage Protection, Power-Supply Overvoltage Detection, Motor and Actuator Limit Detection, Window Comparator and Fault Logic, TTL and CMOS Logic Interfacing.
24 V Industrial Sensor Threshold Detection
The LM2903BIPWR fits 24 V industrial sensor interfaces because its 2 V to 36 V operating range accommodates protected sensor nodes while its 0.37 mV input offset helps distinguish closely spaced trip points. Place one channel across a divided sensor signal and the other at a configurable upper threshold. The open-collector output can directly pull down an isolated digital input or PLC input when the threshold is exceeded, with an external pull-up defining the logic voltage. The 200 µA per-comparator supply current limits continuous overhead, while the 1 µs response time reduces detection delay.
Recommandé
Battery Pack Overvoltage Protection
The LM2903BIPWR is useful for battery-pack protection because its rail-to-rail inputs can monitor a divided pack voltage and its two channels can supervise upper and lower boundaries. Use resistor dividers to bring the cell stack within the comparator input range, then connect the open-collector outputs to a protection latch or disconnect driver. The 200 µA current per comparator limits divider and monitoring overhead, while the 1 µs response supports rapid fault detection. The 36 V operating capability is valuable for industrial battery systems, although the external divider must maintain suitable fault margins.
Recommandé
Power-Supply Overvoltage Detection
The LM2903BIPWR can supervise a rectified or regulated power rail when its monitored voltage is scaled to remain within the 2 V to 36 V comparator range. The two independent channels support separate high and low limits, allowing a compact window comparator without using a dedicated window-comparator IC. An open-collector output can drive a fault latch, relay, or optocoupler through an appropriate pull-up and interface network. Its low 0.37 mV offset supports fine threshold control after amplification, and its 1 µs response time helps minimize the interval between a rail excursion and the protective action.
Recommandé
Motor and Actuator Limit Detection
The LM2903BIPWR suits motor and actuator limit detection where two independent thresholds monitor position, current, or feedback voltages. Its 1 µs response time helps minimize propagation through the comparison stage, while the open-collector output can pull a protection input or gate-driver interface into an active state. The wide 36 V operating range accommodates industrial control rails, and the 200 µA per-comparator current is useful in power-conserving supervisory designs. Input common-mode limits and transient protection remain important when connected to motor-node signals because the comparator package alone does not provide surge protection.
Recommandé
Window Comparator and Fault Logic
The LM2903BIPWR's two independent channels can implement a window detector, with one comparator establishing the lower limit and the other establishing the upper limit. Their open-collector outputs can share a pull-up when wired-AND behavior is required, allowing the combined output to indicate whether a monitored signal is outside its acceptable range. The B-version's 3.5 nA input bias current minimizes error in high-impedance divider networks, and its 0.37 mV offset improves threshold precision. Design the pull-up and downstream logic so the wired output polarity matches the intended fault convention.
Recommandé
TTL and CMOS Logic Interfacing
The LM2903BIPWR can interface industrial sensors with TTL or CMOS logic because its open-collector output requires an external pull-up that can be connected to the destination logic rail. This allows the comparator output voltage to be defined independently of its 2 V to 36 V supply range. The 1 µs response time supports moderately fast threshold events, while the 200 µA per-comparator supply current helps maintain low system overhead. Use a pull-up value that balances input current, switching speed, power dissipation, and the number of outputs connected to the same node.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour LM2903BIPWR — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | LM2903PWR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-pin TSSOP (PW) | 8-pin TSSOP (PW) - same |
| Comparator Configuration | Dual | Dual |
| Maximum Supply Voltage | 38 V | 30 V |
| Supply Current | 200 µA per comparator | 400 µA per comparator |
| Output Type | Open-collector | Open-collector |
Principaux différenciateurs
- Higher supply-voltage capability (vs LM2903PWR)
- Lower supply consumption (vs LM2903PWR)
- Improved B-version signal performance (vs LM2903PWR)
Notes de conception
Route the two non-inverting and two inverting inputs as short, guarded traces, keeping them away from the open-collector outputs and pull-up resistors. High-impedance divider nodes can couple output-edge noise into the reference input and cause false switching. Use a ground reference that returns cleanly to pin 4, and place the supply bypass capacitor close to pins 8 and 4.
Every open-collector output needs an external pull-up resistor. The device can pull the output low, but it cannot actively drive the node high. Select the pull-up supply carefully so it remains within the destination logic's voltage range. When several outputs share one pull-up, verify that the wired-AND polarity produces the intended fault indication and that the combined sink current remains within rating.
Keep the supply voltage between 2 V and 36 V during normal operation and observe the 38 V absolute maximum rating only as a stress limit. The B version's 200 µA supply current per comparator reduces continuous overhead, but divider resistance and pull-up values can dominate total power. Choose the pull-up no larger than necessary for the required switching speed and destination input capacitance.
Do not substitute the LM2903BIPWR solely by comparator function. The replacement must use the same 8-pin TSSOP pin arrangement and meet the required input common-mode, output leakage, supply-voltage, response-time, and temperature limits. The legacy LM2903PWR has the same package and output architecture, but its lower supply-current capability and lower maximum supply rating require circuit-level verification.
Informations de conformité
The device is described by Texas Instruments as an industrial-grade dual comparator. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status for the exact LM2903BIPWR ordering code should be confirmed on the manufacturer product and ordering pages.