LM324KNSR - Quad 30-V 1.2-MHz Op Amp | Texas Instruments
MPN: LM324KNSR ✓ نشطLM324KNSR نظرة عامة
An operational amplifier, or op amp, is a high-gain differential amplifier that compares two input voltages and drives its output to represent their difference. Within the broader semiconductor hierarchy, an op amp is an analog amplifier IC used for signal conditioning, buffering, amplification, filtering, feedback control, and voltage-level conversion. The LM324KNSR integrates four such amplifiers into one package, reducing board area compared with four separate single or dual amplifier packages.
The principal device ratings include operation from a single or split supply, a 30 V maximum supply voltage, 1.2 MHz gain-bandwidth bandwidth, and 2 kV improved ESD protection. The manufacturer identifies LM324KNSR as a standard general-purpose amplifier with four circuits and a 14-pin SOP package. Its specified operating-temperature range is 0 to 70 °C, making it appropriate for commercial equipment where an extended industrial temperature rating is not required.
The LM324K family is designed for broad compatibility with established LM324-type amplifier boards. Because the four amplifiers share a common package but operate independently, separate signal paths can be implemented within one device. The frequency-compensated architecture simplifies closed-loop use when the amplifier is configured as a standard inverting or non-inverting gain stage, although loop stability and bandwidth still depend on the external feedback network and load.
Typical uses include audio preamplification, sensor signal conditioning, current-to-voltage conversion, active filtering, voltage comparison, and general instrumentation. The four-amplifier arrangement is especially useful when a design needs several channels of similar gain and bandwidth, such as multiple sensor inputs or a balanced differential stage followed by additional gain stages.
PCB layout should keep input and feedback connections short and route them away from high-current switching nodes. Decoupling capacitors should be placed close to the power pins, while the unused amplifier in any unused channel must be configured according to the Texas Instruments LM324K datasheet rather than left floating. The 14-pin SOIC footprint simplifies replacement on compatible LM324NS-style boards.
This product record combines manufacturer specifications, package and ordering information, drop-in candidate analysis, comparison parameters, and practical PCB guidance. It helps engineers evaluate the LM324KNSR for general-purpose analog designs and identify whether a same-footprint LM324-family device is appropriate when supply voltage, temperature grade, or sourcing requirements change.
بدائل مباشرة لـ LM324KNSR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM324KNSR (نفس عامل الشكل والبصمة) — يختلف في Package, Supply Configuration, Input Offset Voltage, Maximum Supply Voltage, Amplifier Type.
LM324ANSR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LM324ADR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM324DR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2902NSR
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LM324KNS
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM324KNSR الحدود القصوى والخصائص الكهربائية
| Amplifier Count | 4 independent amplifiers |
| Product Type | Quad general-purpose operational amplifier |
| Maximum Supply Voltage | 30 V |
| Supply Configuration | Single or split supply |
| Gain-Bandwidth Product | 1.2 MHz |
| Improved ESD Protection | 2 kV |
| نطاق درجة حرارة التشغيل | 0 °C to 70 °C |
| العلبة | 14-pin SOIC (NS, SOP) |
| عدد الأطراف | 14 pins |
| نوع التركيب | Surface mount |
| Shipping Form | NSR ordering code |
دليل تكوين أطراف LM324KNSR 14-pin soic (ns, sop)
تكوين الأطراف لـ LM324KNSR (حزمة 14-pin soic (ns, sop)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM324KNSR.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM324KNSR مناسب لـ 6 التطبيقs: General-Purpose Sensor Signal Conditioning, Audio Preamplification, Active Filtering and Control Loops, Power Supply Current Measurement, Instrumentation Buffering, Interface and Level Conditioning.
General-Purpose Sensor Signal Conditioning
The LM324KNSR fits four-channel sensor conditioning because it integrates four independent, frequency-compensated amplifiers with 1.2 MHz gain-bandwidth bandwidth in one 14-pin SOIC package. Each amplifier can scale a low-level sensor signal or drive a feedback network before conversion. The 30 V maximum supply rating supports 5 V, 12 V, and other supply arrangements, while the 0 to 70 °C range targets commercial equipment. Place supply-decoupling capacitors near the package and keep high-impedance input traces short to reduce noise pickup and imbalance error.
موصى به
Audio Preamplification
The LM324KNSR can provide the general-purpose gain stages used around audio sources because each amplifier is frequency compensated and supports single or split supplies. The 1.2 MHz gain-bandwidth bandwidth is sufficient for many low-to-moderate-bandwidth preamplifier and mixer stages, while four amplifiers allow balanced input handling or two stereo channels in one package. The 2 kV improved ESD rating also benefits equipment exposed to electrostatic discharge. Designers should verify output swing and bandwidth at the intended signal amplitude instead of assuming the full 30 V supply can appear at the output.
موصى به
Active Filtering and Control Loops
The four channels in LM324KNSR are useful for active filter and feedback-control implementations where several related amplifier stages share the same supply. The 1.2 MHz gain-bandwidth bandwidth provides a defined performance point for evaluating closed-loop filter response and control-loop compensation. Because the amplifiers are independent, separate filters or a multistage servo loop can be implemented in one 14-pin SOIC. Use the Texas Instruments LM324K gain and phase characteristics to select resistor and capacitor values, and keep sensitive summing nodes away from power-supply and switching traces.
موصى به
Power Supply Current Measurement
LM324KNSR can form the transimpedance and buffering stages of a current-measurement system because it combines four independent amplifiers with a 30 V maximum supply rating. A shunt amplifier, differential sensing stage, output filter, and monitor amplifier can share one package when their signal ranges and bandwidth requirements suit the 1.2 MHz device. The commercial 0 to 70 °C range is appropriate for room-temperature test equipment. Confirm input offset, input bias current, common-mode range, and output swing at the actual shunt voltage before relying on accuracy at microampere or milliampere levels.
موصى به
Instrumentation Buffering
The LM324KNSR is suitable for instrumentation buffering when the design needs several high-input-impedance buffer or gain functions rather than a single precision amplifier. Its four independent channels can isolate sensor outputs, buffer reference voltages, and amplify intermediate signals within one 14-pin SOIC package. The 30 V rating is useful for powered laboratory and industrial control boards, while the 1.2 MHz bandwidth supports many low-frequency measurement paths. The 2 kV improved ESD protection is relevant for bench equipment, although system-level grounding and connector protection still determine real transient immunity.
موصى به
Interface and Level Conditioning
LM324KNSR can condition logic-level, analog-reference, or low-speed communications signals when a board needs several op-amp channels with common supply connections. Single- or split-supply operation supports both grounded and offset signal paths, and the four-amplifier configuration can implement buffering, comparison, gain, and active filtering in parallel. The 1.2 MHz bandwidth is more than adequate for many low-speed interface tasks but should be checked against edge-rate requirements. Route outputs away from fast digital nets and use local supply bypassing to maintain predictable behavior in mixed-signal equipment.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM324KNSR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM324ANSR | LM324ADR | LM324DR | LM2902NSR | LM324KNS |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 14-SOIC (NS) | 14-SOIC (NS) | 14-SOIC | 14-SOIC | 14-SOIC (NS) | 14-SOIC (NS) |
| Amplifier Count | 4 independent amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers | 4 amplifiers |
| Supply Configuration | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply | Single or split supply |
| Special Feature | Improved ESD protection | LM324A family | LM324A family | Legacy LM324 family | LM2902 family | Improved ESD protection |
أبرز الفروقات
- Improved electrostatic-discharge protection in the selected LM324K family (مقابلLM324ADR)
- Commercial-temperature ordering profile (مقابلLM324DR)
- Same LM324K family with direct NS-footprint reuse (مقابلLM324KNS)
- Four independent amplifiers in one package (مقابلLM2902NSR)
ملاحظات التصميم
Place the supply-bypass capacitors immediately beside pins 4 and 11, with short, low-inductance connections to the ground plane. Keep each amplifier's noninverting input, inverting input, and feedback components close together and away from switching nodes. The four amplifiers share supply pins, so a noisy load on one channel can couple through the common supply network; isolate high-current outputs and use local decoupling when necessary.
Treat high-impedance input traces as sensitive nodes because input offset and bias current establish the practical accuracy of a general-purpose amplifier stage. Minimize leakage from PCB contamination, flux residue, humidity, and nearby high-impedance sources. Where the 1.2 MHz device operates near its bandwidth limit, keep feedback loops compact and verify both magnitude and phase margin using the gain-bandwidth and output-capability information in the LM324K datasheet.
Do not assume that the 30 V maximum supply rating permits a 30 V output or unrestricted input range. The valid common-mode input range and output swing depend on the selected supply and output conditions. Likewise, configure every unused amplifier as a stable stage rather than allowing its input to float. Before replacing LM324KNSR with LM324ANSR, LM324ADR, LM324DR, LM2902NSR, or LM324KNS, verify the complete operating limits and pin description for the exact ordering suffix.
معلومات الامتثال
No explicit LM324KNSR compliance declarations or AEC-Q100 qualification were identified. A commercial 0 to 70 °C operating-temperature range is not, by itself, evidence of AEC-Q100 qualification.