LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments
MPN: LM2904AVQPWRG4 ✓ نشطLM2904AVQPWRG4 نظرة عامة
An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 belongs to the operational-amplifier hierarchy, where it serves as a general-purpose amplifier for signal conditioning, buffering, voltage amplification, and feedback-based control. Its common-mode input range includes ground, allowing direct sensing of signals near 0 V.
The device operates from single or dual supplies. The manufacturer specifies operation from up to 26 V total for single-supply operation, or up to 13 V per rail for dual supplies. A typical supply-current drain of 0.7 mA is specified as independent of supply voltage. The two-amplifier configuration also supports independent operation of each channel rather than requiring both channels to perform the same function.
The 700 kHz gain-bandwidth product supports general-purpose amplification at low and moderate frequencies rather than high-speed signal conditioning. Because this is not a rail-to-rail input or output device, the input and output operating regions must remain within the amplifier’s supply-dependent limits. Bias and offset requirements should be checked against the circuit’s signal amplitude and source impedance.
Typical applications include low-frequency sensor conditioning, analog signal buffering, feedback control, audio preamplification, and general instrumentation. The TSSOP package supports compact surface-mount layouts, while the dual channel count reduces component count when two gain stages are needed. In a single-supply system, the input common-mode range extending to ground is especially useful for signals produced by sensors near the lower supply rail.
When laying out the circuit, keep feedback components and input sources close to the appropriate pins, maintain a common ground reference, and decouple the supply connection. Avoid relying on the amplifier for isolation or level translation outside its specified input and output ranges. Stability with capacitive loads should be evaluated because capacitive loading can alter the effective gain-bandwidth response and introduce peaking.
This product page combines the manufacturer’s electrical characteristics with package, sourcing, replacement, and application guidance. It also identifies the differences between verified same-brand family alternatives and highlights the electrical checks required before treating any substitute as a true drop-in replacement.
بدائل مباشرة لـ LM2904AVQPWRG4 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LM2904BIPWRG4
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LM2904BAIPWRG4
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LM2904AIPWRG4
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LM2904AQDWRG4
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها📋 بديل مرجعي (غير موجود في الكتالوج)
LM2902AVQPWRG4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM2904AVQPWRG4 الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 700 kHz |
| Maximum Total Supply Voltage | 26 V |
| Maximum Supply Voltage per Rail | 13 V for dual supplies |
| تيار التغذية | 0.7 mA typical |
| Common-Mode Input Voltage Range | Includes ground |
| Number of Inputs | 4 inputs |
| عدد المخارج | 2 outputs |
| العلبة | 8-TSSOP, 4.40 mm width |
| نوع التركيب | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
تكوين أطراف LM2904AVQPWRG4
| دبوس 1 | OUTA — Amplifier A output |
| دبوس 2 | INA- — Inverting input for amplifier A |
| دبوس 3 | INA+ — Noninverting input for amplifier A |
| دبوس 4 | V+ — Positive supply connection |
| دبوس 5 | INB+ — Noninverting input for amplifier B |
| دبوس 6 | INB- — Inverting input for amplifier B |
| دبوس 7 | OUTB — Amplifier B output |
| دبوس 8 | V- — Negative supply or ground connection |
التطبيقات النموذجية
LM2904AVQPWRG4 مناسب لـ 6 التطبيقs: Low-Frequency Sensor Signal Conditioning, Audio Preamplification, Industrial Instrumentation Buffering, Feedback Control and Voltage Amplification, Automotive Signal Conditioning, General-Purpose Analog Interface.
Low-Frequency Sensor Signal Conditioning
The LM2904AVQPWRG4 fits sensor-amplifier stages that operate near ground because its common-mode input-voltage range includes ground. The 700 kHz gain-bandwidth product is appropriate for sensors with bandwidth well below that level, such as temperature, pressure, and slow position sensors. Each channel can independently amplify a sensor output or form a gain stage around the sensor. Because the device is not described as rail-to-rail, confirm the sensor’s output range against the available supply voltage and the amplifier’s output-swing limits. A single-supply arrangement simplifies grounding and reduces the number of external signal connections.
موصى به
Audio Preamplification
The LM2904AVQPWRG4 can provide modest-gain audio preamplification for source impedances and bandwidths compatible with a 700 kHz gain-bandwidth product. Two independent channels support stereo signal paths, and operation from a single supply is useful when the source signal is referenced to ground. Input and output swing must remain inside the amplifier’s supply-dependent operating region. This device is better suited to general audio conditioning than precision low-noise audio paths where a wide rail-to-rail input range, low distortion, and specified noise performance are essential.
موصى به
Industrial Instrumentation Buffering
The LM2904AVQPWRG4 is appropriate for buffering sensor and measurement lines in compact industrial instruments where a 700 kHz bandwidth and low typical supply-current drain of 0.7 mA are sufficient. The dual-channel package can buffer two related signals or separate instrumentation stages. Its common-mode range including ground supports measurements near the lower supply rail, but the selected supply must still maintain the required input and output voltage range. Place the amplifier close to the source, use a stable ground reference, and decouple the supply pin to minimize noise coupled into sensitive measurement paths.
موصى به
Feedback Control and Voltage Amplification
The LM2904AVQPWRG4 can implement feedback voltage-amplifier and control stages because it provides two operational-amplifier channels and a 700 kHz gain-bandwidth product. The bandwidth is suitable for loops or control paths whose dynamics remain well below the amplifier’s unity-gain bandwidth. Designers should include compensation for loop stability, account for input and output voltage limits, and confirm that the selected supply supports the required output swing. The low 0.7 mA typical supply-current drain can help where power consumption is secondary to simplicity and robustness.
موصى به
Automotive Signal Conditioning
The LM2904AVQPWRG4 is identified as an AEC-Q100-qualified automotive option, making it suitable for qualified general-purpose signal-conditioning positions when its electrical ratings meet the system requirements. Its 700 kHz gain-bandwidth product supports low-frequency vehicle signals rather than high-bandwidth communications. Two channels can process related inputs without adding a second package. Automotive production designs should also observe the manufacturer’s specified temperature range, supply limits, and qualification conditions. PCB layout should provide stable grounding and short feedback paths to reduce susceptibility to electrical transients.
موصى به
General-Purpose Analog Interface
The LM2904AVQPWRG4 can serve as a general analog interface for voltage scaling, impedance buffering, and active filtering in equipment that does not require rail-to-rail operation. Its 700 kHz gain-bandwidth product supports moderate-frequency active filters, while the common-mode range extending to ground simplifies interfaces referenced to the negative supply rail in single-supply systems. Component tolerances and the closed-loop gain determine effective accuracy. Validate filter stability, output loading, and supply bypass layout on the final board rather than relying only on nominal amplifier characteristics.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2904AVQPWRG4 — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM2904BIPWRG4 | LM2904BAIPWRG4 | LM2904AIPWRG4 | LM2904AQDWRG4 | LM2902AVQPWRG4 |
|---|---|---|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-SOIC | 8-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 1 channel |
أبرز الفروقات
- Two independent amplifier channels in one package (مقابلLM2902AVQPWRG4)
- Same-family revised replacement option (مقابلLM2904BIPWRG4)
- Verified automotive pin-compatible option (مقابلLM2902AVQPWRG4)
ملاحظات التصميم
Route each feedback loop locally and connect the bypass capacitor from the V+ pin to the same ground reference used by the circuit. Keep input traces away from the supply pin and output pin to reduce capacitive feedthrough. For a single-supply design, pin 8 normally connects to ground; in a dual-supply design, connect it to the negative supply rail. Confirm the complete pin map in the manufacturer datasheet before releasing PCB artwork.
Do not assume rail-to-rail input or output behavior. The common-mode input range includes ground, but the usable output range still depends on the supply voltage and load. Check the signal’s minimum and maximum values against the datasheet limits. Likewise, confirm that the 700 kHz gain-bandwidth product is adequate for the closed-loop gain, source impedance, and capacitive loading of the intended application.
Use a local supply bypass capacitor at the V+ pin and provide a low-impedance ground return. The typical supply-current drain is 0.7 mA, but actual current varies with supply voltage and output conditions. When two channels drive different loads, evaluate each channel independently because the first and second amplifiers may not present identical loading to the supply and ground pins.
معلومات الامتثال
The verified cross-reference identifies LM2904AVQPWRG4 as AEC-Q100 qualified. Other environmental and material-compliance attributes require confirmation from the manufacturer product documentation.