Texas Instruments

LM2904AVQPWRG4 - Dual 700kHz Op Amp | Texas Instruments

MPN: LM2904AVQPWRG4 ✓ Hoạt động
26 V Vdss 0.7 mA typical Id 8-TSSOP, 4.40 mm width Package
MOQ: 1 |

LM2904AVQPWRG4 Tóm tắt

Texas Instruments LM2904AVQPWRG4 is a dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product, 26 V maximum total supply capability, and an 8-pin TSSOP package. Each amplifier channel provides input, output, and supply connections, allowing one package to implement two independent gain stages or a differential amplifier arrangement.

An operational amplifier is an analog integrated circuit that uses high open-loop gain to amplify the difference between two input voltages. The LM2904 belongs to the operational-amplifier hierarchy, where it serves as a general-purpose amplifier for signal conditioning, buffering, voltage amplification, and feedback-based control. Its common-mode input range includes ground, allowing direct sensing of signals near 0 V.

The device operates from single or dual supplies. The manufacturer specifies operation from up to 26 V total for single-supply operation, or up to 13 V per rail for dual supplies. A typical supply-current drain of 0.7 mA is specified as independent of supply voltage. The two-amplifier configuration also supports independent operation of each channel rather than requiring both channels to perform the same function.

The 700 kHz gain-bandwidth product supports general-purpose amplification at low and moderate frequencies rather than high-speed signal conditioning. Because this is not a rail-to-rail input or output device, the input and output operating regions must remain within the amplifier’s supply-dependent limits. Bias and offset requirements should be checked against the circuit’s signal amplitude and source impedance.

Typical applications include low-frequency sensor conditioning, analog signal buffering, feedback control, audio preamplification, and general instrumentation. The TSSOP package supports compact surface-mount layouts, while the dual channel count reduces component count when two gain stages are needed. In a single-supply system, the input common-mode range extending to ground is especially useful for signals produced by sensors near the lower supply rail.

When laying out the circuit, keep feedback components and input sources close to the appropriate pins, maintain a common ground reference, and decouple the supply connection. Avoid relying on the amplifier for isolation or level translation outside its specified input and output ranges. Stability with capacitive loads should be evaluated because capacitive loading can alter the effective gain-bandwidth response and introduce peaking.

This product page combines the manufacturer’s electrical characteristics with package, sourcing, replacement, and application guidance. It also identifies the differences between verified same-brand family alternatives and highlights the electrical checks required before treating any substitute as a true drop-in replacement.

Bộ thay thế dễ dàng lắp đặt cho LM2904AVQPWRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

LM2904BIPWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-TSSOP
Revised LM2904B-family performance with a 700 kHz-class gain-bandwidth product; the target also uses a 700 kHz gain-bandwidth product, while remaining electrical differences require datasheet verification.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2904BAIPWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-TSSOP
Revised LM2904BA-family offset and bias improvements in the same 8-TSSOP footprint; operating and stability limits must be checked against the target circuit.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2904AIPWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-TSSOP
Same LM2904A family and 700 kHz gain-bandwidth product as the target; ordering-temperature and qualification suffixes require comparison.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2904AQDWRG4

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-SOIC
Same LM2904A-family electrical class with a different 8-SOIC package, so the PCB land pattern differs from 8-TSSOP.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2902AVQPWRG4

✅ Drop-In
📦 8-TSSOP
Pin-to-pin single-channel amplifier rather than a dual amplifier; one device occupies one channel and two devices are required to replace both target channels.

📋 Tham chiếu thay thế (không có trong danh mục)

LM2904AVQPWRG4 Tỷ lệ tối đa & tính chất điện

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 700 kHz
Maximum Total Supply Voltage 26 V
Maximum Supply Voltage per Rail 13 V for dual supplies
Điện áp cung cấp 0.7 mA typical
Common-Mode Input Voltage Range Includes ground
Number of Inputs 4 inputs
Số lượng đầu ra 2 outputs
Hộp 8-TSSOP, 4.40 mm width
Kiểu lắp đặt Surface mount
Automotive Qualification AEC-Q100 qualified

Cấu hình chân LM2904AVQPWRG4

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
Chân 1 OUTA — Amplifier A output
Chân 2 INA- — Inverting input for amplifier A
Chân 3 INA+ — Noninverting input for amplifier A
Chân 4 V+ — Positive supply connection
Chân 5 INB+ — Noninverting input for amplifier B
Chân 6 INB- — Inverting input for amplifier B
Chân 7 OUTB — Amplifier B output
Chân 8 V- — Negative supply or ground connection

Ứng dụng tiêu biểu

LM2904AVQPWRG4 phù hợp cho 6 Áp dụngs: Low-Frequency Sensor Signal Conditioning, Audio Preamplification, Industrial Instrumentation Buffering, Feedback Control and Voltage Amplification, Automotive Signal Conditioning, General-Purpose Analog Interface.

🧩

Low-Frequency Sensor Signal Conditioning

The LM2904AVQPWRG4 fits sensor-amplifier stages that operate near ground because its common-mode input-voltage range includes ground. The 700 kHz gain-bandwidth product is appropriate for sensors with bandwidth well below that level, such as temperature, pressure, and slow position sensors. Each channel can independently amplify a sensor output or form a gain stage around the sensor. Because the device is not described as rail-to-rail, confirm the sensor’s output range against the available supply voltage and the amplifier’s output-swing limits. A single-supply arrangement simplifies grounding and reduces the number of external signal connections.

🎧

Audio Preamplification

The LM2904AVQPWRG4 can provide modest-gain audio preamplification for source impedances and bandwidths compatible with a 700 kHz gain-bandwidth product. Two independent channels support stereo signal paths, and operation from a single supply is useful when the source signal is referenced to ground. Input and output swing must remain inside the amplifier’s supply-dependent operating region. This device is better suited to general audio conditioning than precision low-noise audio paths where a wide rail-to-rail input range, low distortion, and specified noise performance are essential.

🏭

Industrial Instrumentation Buffering

The LM2904AVQPWRG4 is appropriate for buffering sensor and measurement lines in compact industrial instruments where a 700 kHz bandwidth and low typical supply-current drain of 0.7 mA are sufficient. The dual-channel package can buffer two related signals or separate instrumentation stages. Its common-mode range including ground supports measurements near the lower supply rail, but the selected supply must still maintain the required input and output voltage range. Place the amplifier close to the source, use a stable ground reference, and decouple the supply pin to minimize noise coupled into sensitive measurement paths.

🔧

Feedback Control and Voltage Amplification

The LM2904AVQPWRG4 can implement feedback voltage-amplifier and control stages because it provides two operational-amplifier channels and a 700 kHz gain-bandwidth product. The bandwidth is suitable for loops or control paths whose dynamics remain well below the amplifier’s unity-gain bandwidth. Designers should include compensation for loop stability, account for input and output voltage limits, and confirm that the selected supply supports the required output swing. The low 0.7 mA typical supply-current drain can help where power consumption is secondary to simplicity and robustness.

🚗

Automotive Signal Conditioning

The LM2904AVQPWRG4 is identified as an AEC-Q100-qualified automotive option, making it suitable for qualified general-purpose signal-conditioning positions when its electrical ratings meet the system requirements. Its 700 kHz gain-bandwidth product supports low-frequency vehicle signals rather than high-bandwidth communications. Two channels can process related inputs without adding a second package. Automotive production designs should also observe the manufacturer’s specified temperature range, supply limits, and qualification conditions. PCB layout should provide stable grounding and short feedback paths to reduce susceptibility to electrical transients.

⚡

General-Purpose Analog Interface

The LM2904AVQPWRG4 can serve as a general analog interface for voltage scaling, impedance buffering, and active filtering in equipment that does not require rail-to-rail operation. Its 700 kHz gain-bandwidth product supports moderate-frequency active filters, while the common-mode range extending to ground simplifies interfaces referenced to the negative supply rail in single-supply systems. Component tolerances and the closed-loop gain determine effective accuracy. Validate filter stability, output loading, and supply bypass layout on the final board rather than relying only on nominal amplifier characteristics.

Tóm tắt các sản phẩm được đề xuất

LM2904AVQPWRG4 Texas Instruments Được sử dụng trong: Low-Frequency Sensor Signal Conditioning, Audio Preamplification, Industrial Instrumentation Buffering, Feedback Control and Voltage Amplification, Automotive Signal Conditioning, General-Purpose Analog Interface LM2904BIPWRG4 Same-family signal-conditioning alternative Được sử dụng trong: Low-Frequency Sensor Signal Conditioning, Feedback Control and Voltage Amplification LM2904BAIPWRG4 Same-family audio amplification alternative Được sử dụng trong: Audio Preamplification, General-Purpose Analog Interface LM2904AIPWRG4 Same-family instrumentation alternative Được sử dụng trong: Industrial Instrumentation Buffering LM2902AVQPWRG4 Verified AEC-Q100-qualified pin-compatible alternative Được sử dụng trong: Automotive Signal Conditioning
What is the LM2904AVQPWRG4?
The LM2904AVQPWRG4 is a Texas Instruments dual general-purpose operational amplifier with a 700 kHz gain-bandwidth product in an 8-pin TSSOP package. According to the Texas Instruments LM2904 product page and manufacturer datasheet, it is intended for general-purpose analog signal conditioning, buffering, amplification, and feedback-control circuits. The package contains two independent amplifier channels.
What is the operating voltage of LM2904AVQPWRG4?
The LM2904AVQPWRG4 supports operation with up to 26 V total supply voltage in a single-supply configuration or up to 13 V per rail in a dual-supply configuration. According to the Texas Instruments LM2904 manufacturer datasheet, the device can operate from single or dual supplies. Actual signal limits must also remain inside the specified common-mode input and output ranges.
Where can I download the LM2904AVQPWRG4 datasheet PDF?
The official LM2904AVQPWRG4 technical information is available through the Texas Instruments LM2904 product page, which links to the manufacturer datasheet and ordering information. The LM2904AVQPWRG4 is an orderable member of the LM2904 family, so engineers should match the package suffix, temperature grade, and qualification requirements against the ordering information before releasing a design.
Where can I find the LM2904AVQPWRG4 pinout?
The LM2904AVQPWRG4 uses an 8-pin TSSOP arrangement with two complete operational-amplifier channels. According to the Texas Instruments LM2904 manufacturer datasheet, the standard TSSOP connections are pins 1 OUTA, 2 INA−, 3 INA+, 4 V+, 5 INB+, 6 INB−, 7 OUTB, and 8 V−. Pin numbering follows the counter-clockwise convention shown on the package drawing.
What are the key specifications of LM2904AVQPWRG4 that engineers should know?
The principal LM2904AVQPWRG4 specifications are two amplifier channels, a 700 kHz gain-bandwidth product, operation up to 26 V total supply voltage, and a typical 0.7 mA supply-current drain. According to the Texas Instruments LM2904 product page, the common-mode input range includes ground. These characteristics position the device for low-to-moderate-frequency, general-purpose analog signal conditioning rather than high-speed amplification.
Is the LM2904AVQPWRG4 suitable for single-supply sensor conditioning?
Yes, the LM2904AVQPWRG4 is suitable for many single-supply sensor-conditioning circuits because its common-mode input-voltage range includes ground. The Texas Instruments LM2904 manufacturer datasheet identifies a 700 kHz gain-bandwidth product and 26 V total supply capability. The sensor output, amplifier output, and required gain must remain within the operating limits for the selected supply voltage.
What is the LM2904AVQPWRG4 vs LM2902AVQPWRG4 difference?
The LM2904AVQPWRG4 contains two amplifier channels, while the LM2902AVQPWRG4 is a single-channel device. The verified cross-reference information identifies LM2902AVQPWRG4 as pin-to-pin compatible with LM2904AVQPWRG4 and states that both share identical specifications and AEC-Q100 qualification. A board using two LM2902 devices can therefore preserve the physical pin arrangement, but one LM2902 does not replace both LM2904 channels by itself.
When should I choose LM2904AVQPWRG4 over LM2904BIPWRG4?
Choose LM2904AVQPWRG4 when the design specifically calls for the enhanced-voltage LM2904A-family device and its exact ordering suffix. The LM2904B family is a revised alternative, but its offset, bias, noise, and supply-limit details should be compared with the LM2904A datasheet before substitution. According to Texas Instruments guidance, selecting a family successor requires checking offset voltage, supply voltage, and package type.
Is LM2904AVQPWRG4 the same as LM2904BAIPWRG4?
No, LM2904AVQPWRG4 and LM2904BAIPWRG4 are related LM2904-family devices but are not exact-order-code equivalents. The BA designation identifies the revised LM2904B performance family, while the A designation identifies the LM2904A family. Their electrical limits and test criteria must be checked individually, even when both are offered in an 8-pin TSSOP package.
What can replace LM2904AVQPWRG4?
LM2902AVQPWRG4 is a verified pin-to-pin alternative, while LM2904BIPWRG4 and LM2904BAIPWRG4 are same-brand family alternatives in the compatible TSSOP format. The most suitable replacement depends on whether one or two amplifier channels are required and whether revised offset, bias, noise, and supply specifications affect the circuit. Verify every operating limit in the manufacturer datasheet before soldering a substitute.
What is the best Renesas equivalent for LM2904AVQPWRG4?
The Renesas cross-reference search should be used to identify the closest dual operational amplifier with an 8-pin TSSOP footprint and comparable supply, offset, bias-current, and common-mode limits. No specific Renesas MPN is established by the verified material, so naming one would be speculative. The definitive comparison must use the selected Renesas manufacturer datasheet and the LM2904 family datasheet.
Is LM2904AVQPWRG4 in stock and what is the lead time?
Current inventory and delivery timing should be requested through the Request a Quote form on this page. The verified distributor listings confirm that LM2904AVQPWRG4 is catalogued and list inventory or immediate-shipping information, but these conditions change frequently. Confirm the exact suffix, package, quantity, and production schedule before committing the component to a build schedule.
How much does LM2904AVQPWRG4 cost?
Use the Request a Quote form on this page for the current price and volume availability of LM2904AVQPWRG4. The verified listings include unit-price and starting-price information, but a starting-price statement is not a firm quantity-break quotation. A quote should confirm the exact 8-TSSOP order code, quantity, delivery terms, and any traceability requirements.
Can I purchase LM2904AVQPWRG4 online?
The LM2904AVQPWRG4 can be requested online through the Request a Quote form on this page. The exact MPN identifies a dual operational amplifier in an 8-pin TSSOP package from Texas Instruments. Quote requests should specify required quantity, target date, acceptable shipment quantities, and whether the full manufacturer reel or cut tape is needed.
Does LM2904AVQPWRG4 require an external heatsink?
The LM2904AVQPWRG4 does not normally require an external heatsink because its typical supply-current drain is only 0.7 mA and the manufacturer describes it as a general-purpose low-frequency amplifier. According to the Texas Instruments LM2904 manufacturer datasheet, the device is available in a compact TSSOP package. Actual thermal design should still account for maximum supply voltage, output current, and worst-case ambient conditions.

Dữ liệu tham khảo kỹ thuật cho LM2904AVQPWRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose LM2904AVQPWRG4 when the design needs two independent general-purpose amplifier channels, a 700 kHz gain-bandwidth product, operation from a single or dual supply up to 26 V total, and an AEC-Q100-qualified 8-TSSOP option. LM2904BIPWRG4 and LM2904BAIPWRG4 are sensible same-family alternatives when a revised LM2904B-family device satisfies the circuit’s offset, bias, noise, and supply requirements. LM2904AIPWRG4 remains the closest same-family ordering option when the exact LM2904A electrical baseline is required. LM2902AVQPWRG4 is a verified pin-compatible choice, but it has only one amplifier channel, so two devices are needed to replace both target channels. LM2904AQDWRG4 is electrically relevant but uses an 8-SOIC package rather than the target’s 8-TSSOP land pattern and therefore requires a different PCB footprint.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này LM2904BIPWRG4 LM2904BAIPWRG4 LM2904AIPWRG4 LM2904AQDWRG4 LM2902AVQPWRG4
Package 8-TSSOP 8-TSSOP 8-TSSOP 8-TSSOP 8-SOIC 8-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Channels 2 channels 2 channels 2 channels 2 channels 2 channels 1 channel

Bảo phân biệt quan trọng

  • Two independent amplifier channels in one package (vsLM2902AVQPWRG4)
  • Same-family revised replacement option (vsLM2904BIPWRG4)
  • Verified automotive pin-compatible option (vsLM2902AVQPWRG4)

Ghi chú thiết kế

Route each feedback loop locally and connect the bypass capacitor from the V+ pin to the same ground reference used by the circuit. Keep input traces away from the supply pin and output pin to reduce capacitive feedthrough. For a single-supply design, pin 8 normally connects to ground; in a dual-supply design, connect it to the negative supply rail. Confirm the complete pin map in the manufacturer datasheet before releasing PCB artwork.

Do not assume rail-to-rail input or output behavior. The common-mode input range includes ground, but the usable output range still depends on the supply voltage and load. Check the signal’s minimum and maximum values against the datasheet limits. Likewise, confirm that the 700 kHz gain-bandwidth product is adequate for the closed-loop gain, source impedance, and capacitive loading of the intended application.

Use a local supply bypass capacitor at the V+ pin and provide a low-impedance ground return. The typical supply-current drain is 0.7 mA, but actual current varies with supply voltage and output conditions. When two channels drive different loads, evaluate each channel independently because the first and second amplifiers may not present identical loading to the supply and ground pins.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

The verified cross-reference identifies LM2904AVQPWRG4 as AEC-Q100 qualified. Other environmental and material-compliance attributes require confirmation from the manufacturer product documentation.

Tìm kiếm liên quan

LM2904AVQPWRG4 datasheet LM2904AVQPWRG4 pinout LM2904AVQPWRG4 datasheet pdf LM2904AVQPWRG4 equivalent LM2904AVQPWRG4 replacement LM2904AVQPWRG4 price LM2904AVQPWRG4 stock Texas Instruments LM2904AVQPWRG4 LM2904AVQPWRG4 8-TSSOP LM2904AVQPWRG4 application circuit LM2904AVQPWRG4 vs LM2902AVQPWRG4 LM2904 dual operational amplifier

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM2904AVQPWRG4 LM2904 LM2904A LM2904B LM2904BA LM2902AVQPWRG4 dual operational amplifier general-purpose amplifier analog integrated circuit gain-bandwidth product common-mode input voltage single-supply operation dual-supply operation AEC-Q100 8-TSSOP TSSOP package surface-mount package feedback control sensor signal conditioning audio preamplification industrial instrumentation input offset voltage supply-current drain
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ