LM2904P-MAND - Dual 26V 700kHz Op Amp | Texas Instruments
MPN: LM2904P-MAND ✓ نشطLM2904P-MAND نظرة عامة
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM2904 contains two independent, internally frequency-compensated amplifiers, making it suitable for signal conditioning, feedback-control loops, sensor interfaces, and general-purpose analog signal processing. As a dual amplifier, it can implement two functions in one package while reducing board area and component count.
The 26 V supply rating supports higher-voltage industrial and automotive systems than common low-voltage operational amplifiers. A 700 kHz gain-bandwidth figure provides useful bandwidth for general-purpose control and conditioning tasks. The manufacturer identifies the LM2904 family for automotive and industrial control applications, while the standard general-purpose amplifier classification supports use across conventional analog designs.
Each amplifier has its own input and output pins, allowing the two sections to operate independently. Internal frequency compensation simplifies closed-loop implementation without requiring an external compensation network. This makes the device suitable for noninverting and inverting amplifiers, voltage followers, comparators, differential stages, transimpedance functions, and active-filter building blocks where appropriate stability and bandwidth requirements are met.
Common applications include transducer signal conditioning, closed-loop actuator control, low-side current sensing, buffered sensor inputs, and general industrial instrumentation. The dual configuration can also reduce the number of packages in designs requiring two independent amplifier channels, such as a sensor front end paired with a control or output-conditioning channel.
PCB design should preserve the standard 8-pin PDIP footprint and route high-impedance input signals away from switching nodes and output pins. Stable operation depends on suitable feedback compensation, source impedance, load capability, bypass capacitors, and supply decoupling. The LM2904P-MAND is best selected when its 26 V supply capability and dual channel count match the system while its 700 kHz bandwidth is adequate for the intended signal or control loop.
This page combines the manufacturer product specifications with application guidance, pin mapping, verified-source links, and practical drop-in comparison data. It is designed to help engineers identify the correct operational-amplifier footprint, evaluate supply and bandwidth requirements, and plan PCB integration without relying on generic dual-op-amp assumptions.
بدائل مباشرة لـ LM2904P-MAND — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM2904P-MAND (نفس عامل الشكل والبصمة) — يختلف في Package, Gain-Bandwidth Product, Amplifier Type.
LM2904P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2904ANG
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2904P
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2904P-MAND الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 |
| Maximum Supply Voltage | 26 V |
| Gain-Bandwidth Product | 700 kHz |
| Architecture | Two independent, internally frequency-compensated amplifiers |
| العلبة | 8-pin PDIP |
| نوع التركيب | Through-hole |
| Supply Configuration | Single supply |
| Primary Application | Automotive and industrial control systems |
تكوين أطراف LM2904P-MAND
| دبوس 1 | OUT1 — Amplifier 1 output |
| دبوس 2 | -IN1 — Amplifier 1 inverting input |
| دبوس 3 | +IN1 — Amplifier 1 non-inverting input |
| دبوس 4 | V- — Negative supply or ground connection |
| دبوس 5 | +IN2 — Amplifier 2 non-inverting input |
| دبوس 6 | -IN2 — Amplifier 2 inverting input |
| دبوس 7 | OUT2 — Amplifier 2 output |
| دبوس 8 | V+ — Positive supply connection |
التطبيقات النموذجية
LM2904P-MAND مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Automotive Control-Signal Conditioning, Current-Sense Amplifier, Active Filter and Frequency Compensation, Data Acquisition Front End, Power-Supply Feedback and Monitoring.
Industrial Sensor Signal Conditioning
The LM2904P-MAND fits industrial sensor-conditioning circuits that require two independent analog channels and a higher-voltage supply environment than typical low-voltage precision amplifiers provide. Its two internally frequency-compensated amplifiers can form a noninverting or inverting gain stage, while the 26 V family supply rating supports systems operating above conventional 5 V or 3.3 V rails. The 700 kHz gain-bandwidth characteristic permits useful closed-loop bandwidth for moderately responsive process-control signals. Design the first stage around the sensor output range, check the selected amplifier’s common-mode and output-swing limits, and place bypass capacitors close to the supply pins.
موصى به
Automotive Control-Signal Conditioning
The LM2904P-MAND is suitable for general-purpose automotive control electronics where a dual through-hole operational amplifier is acceptable. Two independent channels can condition separate sensor or switch signals without duplicating an entire amplifier package, and the 26 V supply rating aligns with higher-voltage automotive and industrial environments. The 700 kHz gain-bandwidth product is suitable for low-to-moderate-frequency control and filtering functions rather than precision signal-chain requirements at high frequency. Engineers should confirm the exact ordering code’s qualification and temperature requirements, protect input paths from automotive transients, and verify the chosen gain against the device’s full operating limits.
موصى به
Current-Sense Amplifier
The LM2904P-MAND can implement a single-ended current-sense amplifier in applications where the sense voltage is small and bandwidth requirements are modest. One amplifier channel can amplify the voltage developed across a low-value shunt, while the second channel can provide buffering, offset correction, or an independent monitoring function. The 700 kHz gain-bandwidth rating provides a practical bandwidth ceiling, and the dual package can simplify implementation where a second signal chain is also needed. The input common-mode voltage, input offset voltage, shunt resistance, amplifier gain, and output-swing limits must be checked before applying the device.
موصى به
Active Filter and Frequency Compensation
The LM2904P-MAND can support active low-pass, high-pass, or second-order filter stages when the required signal bandwidth remains comfortably below its 700 kHz gain-bandwidth capability. Two independent amplifiers permit cascaded sections, a Sallen-Key stage, or a combined filter and buffer on one board. Internal frequency compensation reduces external compensation-component requirements for many closed-loop configurations, although component tolerances, source impedance, and load impedance still affect response. Choose resistor and capacitor values against the manufacturer’s stability guidance, test gain peaking with the actual source and load, and maintain the intended common-mode range throughout the passband.
موصى به
Data Acquisition Front End
The LM2904P-MAND is useful in compact data-acquisition front ends that must amplify or buffer inputs before conversion or digitization. Its two independent channels can serve as a differential input stage, a gain stage, or a pair of buffered sensor channels, while the 26 V supply capability accommodates higher-voltage industrial interfaces. The 700 kHz bandwidth is appropriate for many slowly varying measurement signals but not for high-speed waveform acquisition. Select the closed-loop gain so that signal bandwidth and phase margin remain acceptable, verify input common-mode limits for every input excursion, and account for offset and bias-current errors at the selected gain.
موصى به
Power-Supply Feedback and Monitoring
The LM2904P-MAND can monitor a supply rail or participate in a feedback-control loop in industrial power systems using its two independent amplifier channels. One section may buffer a divided feedback signal, while the other can amplify the error against a reference for an analog control function. The 26 V supply rating is useful when the amplifier operates from a nominal 24 V industrial bus with appropriate protection, and 700 kHz bandwidth is sufficient for many slow regulation loops. Do not exceed the absolute supply limit, include input filtering for switching-node coupling, and ensure the feedback divider keeps the amplifier input within its common-mode range at startup and during fault conditions.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2904P-MAND — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM2904P | LM2904ANG | LM2904P |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Package | 8-PDIP | 8-PDIP | 8-PDIP | 8-PDIP |
| Amplifier Configuration | Dual | Dual | Dual | Dual |
| Maximum Supply Voltage | 26 V | 26 V | 26 V | 26 V |
| Number of Independent Amplifiers | 2 | 2 | 2 | 2 |
أبرز الفروقات
- Maintains the same verified 26 V supply class as the closest same-brand candidates (مقابلLM2904P)
- Provides two independent amplifier channels in one through-hole package (مقابلLM324KAPWR)
- Offers a 700 kHz gain-bandwidth product for general-purpose control signals (مقابلLM2904ANG)
ملاحظات التصميم
Treat the two amplifier channels as separate signal paths even though they share one package. Keep high-impedance input traces away from OUT1, OUT2, and switching inductors, and avoid routing input and output paths in parallel to minimize capacitive coupling. Place the supply bypass capacitor close to pin 8 and the ground return close to pin 4 so switching-current loops do not share sensitive signal-ground paths.
Do not treat the 26 V family rating as a recommended operating point. The design must remain below the maximum supply voltage with transient margin, and protection may be required for industrial or automotive transients. Also verify the input common-mode range, output swing, source impedance, and load drive at the intended gain before finalizing the schematic.
Calculate the closed-loop bandwidth from the 700 kHz gain-bandwidth value and the selected noise gain. The signal source should present an impedance low enough for the amplifier input stage, and the load should not exceed the output-drive capability. For filtering applications, simulate component tolerances and source/load parasitics to check for unexpected peaking near the intended cutoff.
Use the manufacturer package drawing to preserve the 8-pin PDIP footprint and observe the notch or pin-1 orientation during assembly. Avoid excessive thermal exposure during manual soldering because the through-hole package can move before the joints cool. Maintain adequate spacing around the package for inspection and rework, particularly in densely populated control boards.
معلومات الامتثال
The LM2904 family is identified for automotive and industrial control applications, but no exact RoHS, REACH, lead-free, halogen-free, conflict-minerals, or AEC-Q100 statement was confirmed for LM2904P-MAND. Confirm the exact ordering code in the manufacturer product documentation before qualification.