LM358AWDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics
MPN: LM358AWDT ✓ نشطLM358AWDT نظرة عامة
An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Each amplifier in the dual package can amplify noninverting or inverting signals, while negative feedback defines the closed-loop gain and bandwidth. This makes the device useful where a sensor, divider, comparator, or analog front end needs a higher-current drive than the preceding circuit can provide.
The LM358AWDT offers two independent amplifiers in one 8-SOIC package, reducing board area compared with two separate single amplifiers. Its 1.1 MHz bandwidth supports general-purpose signal paths operating well below megahertz data rates. The low-power architecture also makes the device appropriate for battery-operated, test, measurement, and embedded-control equipment, subject to the device-specific limits in the manufacturer datasheet.
Operationally, the part combines input, output, and biasing functions within each amplifier section. The output stage must remain within its voltage limits, so designers should provide suitable load current and verify common-mode and output-swing conditions at the actual supply voltage. Feedback components set the gain and bandwidth; choosing resistor and capacitor values consistent with the amplifier’s stable operating region is essential for predictable behavior.
Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filtering, bridge or differential signal conditioning, and general feedback control. Two amplifiers in one package can also handle a matched pair of channels when their grounding, decoupling, and signal paths are laid out carefully. The same package size simplifies replacement with compatible SOIC-8 dual operational amplifiers when their electrical ratings and pin functions have been checked.
The primary layout consideration is decoupling. Place a suitable supply bypass capacitor close to the power pin, keep the feedback loop compact, and route output and input signals away from the noisy supply and ground-return paths. Avoid using the ground lead as a high-current return for external loads, because resistance in the ground trace can introduce gain error and channel coupling.
This product page combines the LM358AWDT ordering information, package identification, operating limits, verified listings, drop-in candidate analysis, and practical implementation guidance. It also highlights where engineers must consult the manufacturer datasheet for detailed pin descriptions, input limits, offset, current, noise, and recommended application circuits before completing a production design.
بدائل مباشرة لـ LM358AWDT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع LM358AWDT (نفس عامل الشكل والبصمة) — يختلف في Package, Amplifier Type, Slew Rate, Input Offset Voltage, Supply Voltage (Single).
LM358DT
✅ بديل مباشر✗ غير متوفر
$0.0509 / وحدة
عرض ورقة البيانات ←LM358D
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←LM358ADDR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2904DR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←RC4558DR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
LM358AWDT الحدود القصوى والخصائص الكهربائية
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Amplifiers | 2 circuits |
| Unity-Gain Bandwidth | 1.1 MHz |
| Maximum Operating Temperature | 70 °C |
| العلبة | 8-SOIC |
| نوع التركيب | Surface mount |
دليل تكوين أطراف LM358AWDT 8-soic
تكوين الأطراف لـ LM358AWDT (حزمة 8-soic). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM358AWDT.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM358AWDT مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Battery-Powered Instrumentation, Active Audio and Control Filtering, Test and Measurement Buffering, Process Control Interface, Portable Sensor and IoT Modules.
Industrial Sensor Signal Conditioning
The LM358AWDT fits two-stage sensor conditioning where a transducer produces a small signal that must be amplified before conversion or comparison. Its two amplifiers in one 8-SOIC package can provide an inverting or noninverting gain stage and a unity-gain buffer, reducing board area while preserving a 1.1 MHz published bandwidth. Place the amplifier close to the sensor source, use short feedback paths, and provide local supply bypassing to minimize pickup and ground-drop error. The application must remain within the device’s 70 °C maximum operating temperature, while the manufacturer datasheet should be consulted for input common-mode range, output swing, offset, and bias-current limits.
موصى به
Battery-Powered Instrumentation
LM358AWDT is useful in low-power instrumentation that must amplify or buffer signals without consuming unnecessary board area. The dual configuration supports two measurement channels, a gain stage followed by a buffer, or an instrumentation amplifier arrangement built from multiple amplifier sections. Its low-power designation and 1.1 MHz unity-gain bandwidth provide a practical combination for low-frequency sensor signals. Battery-operated designs should still verify supply current and rail-to-rail performance because those values are not established by the product listing. Use a common ground reference, avoid injecting sensor current into the IC ground pin, and select capacitor values that remain within the feedback network’s intended bandwidth.
موصى به
Active Audio and Control Filtering
The LM358AWDT can implement active low-pass, high-pass, or notch-filter stages in audio monitoring and industrial control equipment. Its published 1.1 MHz unity-gain bandwidth gives the design headroom beyond many low-frequency control signals, while the two amplifier sections support cascaded stages or buffer isolation between filter sections. Component tolerances directly determine the filter’s cutoff frequency and attenuation, so use resistor and capacitor values calculated for the intended gain. Keep the op-amp feedback loop compact and place input and output protection components where they cannot introduce excessive loading. Confirm output-swing and load-current limits in the manufacturer datasheet for headphone, line, or speaker-adjacent circuits.
موصى به
Test and Measurement Buffering
LM358AWDT is suitable for buffering sensor, divider, or probe outputs in test and measurement systems where a high-impedance source must drive a subsequent instrument stage. The dual 8-SOIC package allows one section to amplify and the other to buffer, while its 1.1 MHz bandwidth is appropriate for many general-purpose low-frequency measurements. Keep input bias current in mind when selecting source impedance, because the bias current can create an offset across a high-value source resistance. Use short, shielded signal routes and a stable reference ground to preserve measurement integrity. The 70 °C maximum operating temperature should be checked against enclosure temperatures, and supply, offset, and noise limits should be verified in the manufacturer datasheet.
موصى به
Process Control Interface
LM358AWDT can support low-level process-control interfaces where a controller requires amplified sensor feedback or a conditioned comparator input. The two internal amplifier sections can be assigned to separate control or monitoring functions, reducing component count within an 8-SOIC footprint. Its 1.1 MHz bandwidth is more than adequate for many slow process variables, and the general-purpose architecture simplifies standard feedback networks. Designers must verify the amplifier’s input common-mode range and output swing against the controller’s supply voltage, including behavior during startup. Add input filtering appropriate to the sensor environment, maintain solid ground returns, and keep feedback loops away from switching nodes to reduce coupling into the measured signal.
موصى به
Portable Sensor and IoT Modules
LM358AWDT fits portable sensing modules that require analog amplification close to the sensor before digital conversion. The low-power dual-amplifier configuration supports a compact 8-SOIC layout, and the 1.1 MHz bandwidth is suitable for many sensor signals below that frequency. Local decoupling helps isolate the analog section from supply variations, while short traces between the sensor, amplifier, and converter reduce noise pickup. Because the device’s maximum operating temperature is 70 °C, it should not be assumed suitable for hot automotive, outdoor, or high-temperature industrial locations without a grade that covers the intended environment. Verify supply current, noise, offset, and input-range behavior before finalizing a low-power design.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM358AWDT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | LM358DT | LM358D | LM358A | LM2904DR | RC4558DR |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC option | 8-SOIC | 8-SOIC |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | Texas Instruments | onsemi | Texas Instruments |
| Number of Amplifiers | 2 circuits | 2 circuits | 2 circuits | Dual | 2 circuits | 2 circuits |
| Number of Channels | 2 | 2 | 2 | 2 | 2 | 2 |
أبرز الفروقات
- Higher published bandwidth than the TI LM358A candidate (مقابلLM358A)
- Confirmed 70 °C operating-temperature ceiling (مقابلRC4558DR)
- Dual amplifier integration in a compact package (مقابلLM2904DR)
ملاحظات التصميم
Place the supply bypass capacitor immediately beside the LM358AWDT power pin and connect it to the device ground reference with a short path. Keep each feedback loop compact and route the noninverting input away from supply, output, and switching-node traces. This is especially important in sensor-conditioning circuits because long, high-impedance input routes can couple noise directly into the amplified output.
Do not assume that two amplifiers in one package may share arbitrary output and input loads. Check each amplifier’s output-current capability, load impedance, output-swing range, and stability conditions in the manufacturer datasheet. The 70 °C maximum operating temperature must also be compared with the highest expected PCB or enclosure temperature rather than only the nominal ambient condition.
Use a single defined analog ground return for the sensor, amplifier, and downstream converter rather than routing external load current through the IC ground pin. Ground bounce caused by shared return paths can look like input offset and can couple one channel into the other. Where the circuit requires isolation, follow the manufacturer’s grounding and decoupling recommendations and verify the assembled board with appropriate instrumentation.
معلومات الامتثال
No explicit compliance declarations for the exact LM358AWDT suffix were established in the retrieved product and cross-reference records. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status from the current manufacturer product documentation before qualification.