STMicroelectronics

LM358AWDT - Dual 1.1MHz Low-Power Op Amp | STMicroelectronics

Référence : LM358AWDT ✓ Actif
8-SOIC Package
MOQ : 1 |

LM358AWDT Présentation

STMicroelectronics LM358AWDT is a low-power dual operational amplifier packaged in an 8-pin SOIC. The device contains two amplifiers, operates from a single supply, and is specified at 1.1 MHz unity-gain bandwidth with a 70°C maximum operating temperature. Its general-purpose design makes it suitable for signal conditioning, buffering, and analog amplification in industrial and embedded systems.

An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify the difference between two input voltages. The LM358 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors. Each amplifier in the dual package can amplify noninverting or inverting signals, while negative feedback defines the closed-loop gain and bandwidth. This makes the device useful where a sensor, divider, comparator, or analog front end needs a higher-current drive than the preceding circuit can provide.

The LM358AWDT offers two independent amplifiers in one 8-SOIC package, reducing board area compared with two separate single amplifiers. Its 1.1 MHz bandwidth supports general-purpose signal paths operating well below megahertz data rates. The low-power architecture also makes the device appropriate for battery-operated, test, measurement, and embedded-control equipment, subject to the device-specific limits in the manufacturer datasheet.

Operationally, the part combines input, output, and biasing functions within each amplifier section. The output stage must remain within its voltage limits, so designers should provide suitable load current and verify common-mode and output-swing conditions at the actual supply voltage. Feedback components set the gain and bandwidth; choosing resistor and capacitor values consistent with the amplifier’s stable operating region is essential for predictable behavior.

Typical applications include buffering sensor outputs, amplifying low-level analog signals, active filtering, bridge or differential signal conditioning, and general feedback control. Two amplifiers in one package can also handle a matched pair of channels when their grounding, decoupling, and signal paths are laid out carefully. The same package size simplifies replacement with compatible SOIC-8 dual operational amplifiers when their electrical ratings and pin functions have been checked.

The primary layout consideration is decoupling. Place a suitable supply bypass capacitor close to the power pin, keep the feedback loop compact, and route output and input signals away from the noisy supply and ground-return paths. Avoid using the ground lead as a high-current return for external loads, because resistance in the ground trace can introduce gain error and channel coupling.

This product page combines the LM358AWDT ordering information, package identification, operating limits, verified listings, drop-in candidate analysis, and practical implementation guidance. It also highlights where engineers must consult the manufacturer datasheet for detailed pin descriptions, input limits, offset, current, noise, and recommended application circuits before completing a production design.

Alternatives de remplacement direct pour LM358AWDT — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec LM358AWDT (même facteur de forme et même empreinte) — différant par Package, Amplifier Type, Slew Rate, Input Offset Voltage, Supply Voltage (Single).

Texas Instruments
Package: 8-SOIC (D)
Amplifier Type: General Purpose
Slew Rate: 0.3 V/us
Comparer avec LM358AWDT →
Texas Instruments
Package: SOIC-8 (D)
Amplifier Type: General Purpose, Bipolar
Slew Rate: 0.3 V/us
Comparer avec LM358AWDT →
Texas Instruments
Package: SOIC-8 (D)
Amplifier Type: General Purpose Operational Amplifier
Slew Rate: 0.3 V/µs
Comparer avec LM358AWDT →
STMicroelectronics
Package: SOIC-8 (SO-8)
Slew Rate: 0.6 V/µs
Input Offset Voltage: 2 mV (typical)
Comparer avec LM358AWDT →

LM358DT

✅ Remplacement direct
STMicroelectronics
📦 8-SOIC
2 · 3 V to 32 V · ±1.5 V to ±16 V · 350 µA (typical) · 2 mV (typical) · 45 nA (typical) · 1.1 MHz · 0.6 V/µs

✗ Rupture de stock

$0.0509 / unité

Voir la fiche technique →

LM358D

✅ Remplacement direct ⚠️ Spécifications non vérifiées
Texas Instruments
📦 8-SOIC
General Purpose Operational Amplifier · 2 · 700 kHz · 0.3 V/µs · 3 V to 32 V · ±1.5 V to ±16 V · 0.7 mA (typ) · 2 mV (typ), 7 mV (max)

Contactez-nous pour le prix

Voir la fiche technique →

LM358ADDR

✅ Remplacement direct
Texas Instruments
📦 8-SOIC
2 · 3 V to 30 V · +/-1.5 V to +/-15 V · 700 kHz · 0.3 V/us · 3 mV · 500 uA · Includes ground (single-supply)

Contactez-nous pour le prix

Voir la fiche technique →

LM2904DR

✅ Remplacement direct
Texas Instruments
📦 8-SOIC
2 · 3 V to 26 V · ±1.5 V to ±13 V · 700 kHz · 0.3 V/us · 2 mV (typical) · 500 uA (typical) · 0.7 mA (typical)

Contactez-nous pour le prix

Voir la fiche technique →

RC4558DR

✅ Remplacement direct
📦 8-SOIC
The dual general-purpose topology and 8-SOIC footprint match, while offset voltage, bandwidth, noise, and temperature-range differences require comparison with the target limits.

📋 Alternative de référence (hors catalogue)

LM358AWDT Valeurs maximales et caractéristiques électriques

Amplifier Type Dual general-purpose operational amplifier
Number of Amplifiers 2 circuits
Unity-Gain Bandwidth 1.1 MHz
Maximum Operating Temperature 70 °C
Boîtier 8-SOIC
Type de montage Surface mount

Guide de configuration des broches du LM358AWDT 8-soic

Configuration des broches du LM358AWDT (boîtier 8-soic). Ce composant analogique comporte des broches d'entrée, de sortie et d'alimentation. Consultez la fiche technique du fabricant pour les configurations des broches d'annulation d'offset, de compensation et d'activation. Idéal pour le conditionnement de signaux et les circuits amplificateurs.

Schéma de brochage du boîtier 8-soic pour le LM358AWDT

Aucune donnée de brochage détaillée disponible pour LM358AWDT.

Consultez la fiche technique pour la configuration complète des broches.

Applications typiques

LM358AWDT convient pour 6 applications: Industrial Sensor Signal Conditioning, Battery-Powered Instrumentation, Active Audio and Control Filtering, Test and Measurement Buffering, Process Control Interface, Portable Sensor and IoT Modules.

🏭

Industrial Sensor Signal Conditioning

The LM358AWDT fits two-stage sensor conditioning where a transducer produces a small signal that must be amplified before conversion or comparison. Its two amplifiers in one 8-SOIC package can provide an inverting or noninverting gain stage and a unity-gain buffer, reducing board area while preserving a 1.1 MHz published bandwidth. Place the amplifier close to the sensor source, use short feedback paths, and provide local supply bypassing to minimize pickup and ground-drop error. The application must remain within the device’s 70 °C maximum operating temperature, while the manufacturer datasheet should be consulted for input common-mode range, output swing, offset, and bias-current limits.

🔧

Battery-Powered Instrumentation

LM358AWDT is useful in low-power instrumentation that must amplify or buffer signals without consuming unnecessary board area. The dual configuration supports two measurement channels, a gain stage followed by a buffer, or an instrumentation amplifier arrangement built from multiple amplifier sections. Its low-power designation and 1.1 MHz unity-gain bandwidth provide a practical combination for low-frequency sensor signals. Battery-operated designs should still verify supply current and rail-to-rail performance because those values are not established by the product listing. Use a common ground reference, avoid injecting sensor current into the IC ground pin, and select capacitor values that remain within the feedback network’s intended bandwidth.

🎧

Active Audio and Control Filtering

The LM358AWDT can implement active low-pass, high-pass, or notch-filter stages in audio monitoring and industrial control equipment. Its published 1.1 MHz unity-gain bandwidth gives the design headroom beyond many low-frequency control signals, while the two amplifier sections support cascaded stages or buffer isolation between filter sections. Component tolerances directly determine the filter’s cutoff frequency and attenuation, so use resistor and capacitor values calculated for the intended gain. Keep the op-amp feedback loop compact and place input and output protection components where they cannot introduce excessive loading. Confirm output-swing and load-current limits in the manufacturer datasheet for headphone, line, or speaker-adjacent circuits.

🔧

Test and Measurement Buffering

LM358AWDT is suitable for buffering sensor, divider, or probe outputs in test and measurement systems where a high-impedance source must drive a subsequent instrument stage. The dual 8-SOIC package allows one section to amplify and the other to buffer, while its 1.1 MHz bandwidth is appropriate for many general-purpose low-frequency measurements. Keep input bias current in mind when selecting source impedance, because the bias current can create an offset across a high-value source resistance. Use short, shielded signal routes and a stable reference ground to preserve measurement integrity. The 70 °C maximum operating temperature should be checked against enclosure temperatures, and supply, offset, and noise limits should be verified in the manufacturer datasheet.

🏭

Process Control Interface

LM358AWDT can support low-level process-control interfaces where a controller requires amplified sensor feedback or a conditioned comparator input. The two internal amplifier sections can be assigned to separate control or monitoring functions, reducing component count within an 8-SOIC footprint. Its 1.1 MHz bandwidth is more than adequate for many slow process variables, and the general-purpose architecture simplifies standard feedback networks. Designers must verify the amplifier’s input common-mode range and output swing against the controller’s supply voltage, including behavior during startup. Add input filtering appropriate to the sensor environment, maintain solid ground returns, and keep feedback loops away from switching nodes to reduce coupling into the measured signal.

🧩

Portable Sensor and IoT Modules

LM358AWDT fits portable sensing modules that require analog amplification close to the sensor before digital conversion. The low-power dual-amplifier configuration supports a compact 8-SOIC layout, and the 1.1 MHz bandwidth is suitable for many sensor signals below that frequency. Local decoupling helps isolate the analog section from supply variations, while short traces between the sensor, amplifier, and converter reduce noise pickup. Because the device’s maximum operating temperature is 70 °C, it should not be assumed suitable for hot automotive, outdoor, or high-temperature industrial locations without a grade that covers the intended environment. Verify supply current, noise, offset, and input-range behavior before finalizing a low-power design.

What is the LM358AWDT?
The LM358AWDT is an STMicroelectronics low-power dual operational amplifier in an 8-SOIC package. According to the manufacturer datasheet description, it provides two general-purpose amplifier circuits with a published unity-gain bandwidth of 1.1 MHz. The device is intended for general analog signal conditioning, buffering, amplification, and feedback-control circuits where two amplifier sections in one package simplify the layout.
What is the operating voltage range of LM358AWDT?
The LM358AWDT operating-voltage range is defined in the STMicroelectronics manufacturer datasheet and should be taken from its absolute-maximum and recommended-operating-condition tables. The retrieved product information confirms that this is an 8-SOIC dual operational amplifier but does not state the numerical supply limits. Use the datasheet limits when selecting the supply rail and checking input and output headroom.
Where can I download the LM358AWDT datasheet PDF?
The LM358AWDT datasheet is available through the STMicroelectronics product documentation and the datasheet listing identified on this page. The manufacturer datasheet is the authoritative source for the complete pin description, electrical characteristics, recommended operating conditions, and application information. The linked datasheet archive also identifies the document as an 18-page low-power dual operational-amplifier datasheet.
Where can I find the LM358AWDT pinout?
The LM358AWDT pinout is identified as an 8-SOIC package, with two operational-amplifier sections. Use the pin-description table and package drawing in the STMicroelectronics manufacturer datasheet when assigning each connection. The retrieved listing confirms the 8-SOIC format, but it does not reproduce all eight terminal names, so the complete pin map should be transferred directly from the manufacturer’s package diagram.
What are the key specifications of LM358AWDT that engineers should know?
The principal confirmed specifications for the LM358AWDT are two amplifier circuits, 1.1 MHz unity-gain bandwidth, a maximum operating temperature of 70 °C, and an 8-SOIC surface-mount package. These characteristics position it as a general-purpose, low-power dual operational amplifier. Supply range, offset, input bias current, slew rate, output swing, noise, and current limits require confirmation in the manufacturer datasheet.
Where can I buy LM358AWDT online?
Use the Request a Quote form on this page to request LM358AWDT availability, current commercial terms, and a quotation for the required quantity. The product is listed by STMicroelectronics and appears in multiple authorized-product and distributor listings. Quote requests through this page allow the exact suffix, package, delivery quantity, and any required traceability documents to be confirmed together.
What is the price of LM358AWDT?
The current commercial price for LM358AWDT should be requested through the Request a Quote form on this page. Structured listing evidence is used here only when a supplier prints explicit quantity-break prices for this exact suffix, and no qualifying USD quantity-break table was found. The request form allows the quantity, packaging, delivery destination, and required supply-chain documentation to be considered in the quotation.
Is LM358AWDT in stock and what is its lead time?
Current stock and lead time for LM358AWDT should be confirmed through the Request a Quote form on this page. The manufacturer online store and distributor records show that the exact LM358AWDT orderable part is actively offered, but availability can change by quantity, date, and destination. Request the current on-hand quantity, scheduled delivery date, minimum order quantity, and factory allocation status.
What can replace LM358AWDT?
A replacement for LM358AWDT must use the same 8-SOIC footprint, preserve both amplifier pin functions, and meet the actual supply-voltage, input-range, output-swing, bandwidth, and load-current requirements. LM358DT, TI LM358A-family devices, LM2904DR, and RC4558DR are listed as drop-in candidates, but each candidate requires datasheet and qualification checks. The Request a Quote form can identify the current manufacturer’s approved equivalents.
Is LM358AWDT the same as LM358DT?
LM358AWDT and LM358DT are both STMicroelectronics LM358-family dual operational amplifiers associated with an 8-SOIC footprint, but their ordering suffixes can encode different grade or delivery conditions. A component comparison identifies LM358DT as a distinct orderable variant from LM358AWDT. Confirm temperature grade, electrical limits, packing code, and marking requirements before treating either device as a substitution.
LM358AWDT vs LM358DT: which is better for a new design?
LM358AWDT is the better selection when its confirmed 1.1 MHz bandwidth, 70 °C maximum operating temperature, and exact STMicroelectronics ordering requirements match the design. LM358DT may be preferable when its grade or qualification attributes better fit the application. Because the retrieved comparison does not provide a complete side-by-side electrical table, review the manufacturer datasheets for both suffixes before deciding.
When should I choose LM358AWDT over another dual SOIC op amp?
Choose LM358AWDT when the design needs two general-purpose amplifier channels in one 8-SOIC package, supports a 1.1 MHz-class bandwidth signal path, and remains within the 70 °C maximum operating-temperature specification. Retain it over another dual amplifier when STMicroelectronics qualification, exact ordering continuity, or validated sourcing is important. Choose a different device if the circuit needs wider bandwidth, lower offset, rail-to-rail operation, lower noise, or a different temperature grade.
Is LM358AWDT suitable for industrial sensor conditioning?
LM358AWDT can be suitable for industrial sensor-conditioning circuits when the application remains within its 70 °C maximum operating temperature and all electrical limits from the manufacturer datasheet are satisfied. The dual 1.1 MHz amplifier configuration is useful for buffering, gain stages, and active filters. Validate input common-mode range, output swing, noise, offset, electromagnetic interference, and temperature drift at the system level.
Can LM2904DR replace LM358AWDT?
LM2904DR can be considered a footprint-compatible alternative because it is identified as an LM358-family equivalent in the cross-reference information and uses the dual SOIC-8 format. Compatibility is not automatic: verify supply range, input common-mode limits, output swing, offset, bias current, noise, slew rate, load capability, and temperature grade. The 70 °C maximum rating of the target also requires explicit attention in an industrial design.
What is the best TI equivalent for LM358AWDT?
The TI LM358A family is the leading cross-brand candidate because the manufacturer identifies it as a dual, 30 V, 700 kHz, 3 mV offset-voltage operational amplifier. A SOIC-8 ordering option may support footprint reuse, but its 700 kHz bandwidth is approximately 36% below the LM358AWDT’s 1.1 MHz bandwidth. Confirm the exact TI suffix, pinout, electrical ratings, temperature grade, and qualification before substitution.

Données de référence d'ingénierie pour LM358AWDT — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose LM358AWDT for general-purpose dual analog signal conditioning when the design fits its confirmed 1.1 MHz bandwidth, 8-SOIC footprint, and 70 °C maximum operating temperature. Select LM358DT when that ordering suffix provides the required STMicroelectronics grade or delivery condition; verify the manufacturer tables before interchangeability is assumed. Consider LM358A when its 30 V maximum supply rating and 3 mV offset are advantageous, but account for its 700 kHz bandwidth, which is about 36% below the target. LM2904DR may suit an LM358-family-compatible design requiring a different manufacturer source, while RC4558DR may be useful when its offset, noise, bandwidth, and temperature characteristics better match the circuit. For every alternative, confirm the complete pinout, supply range, input and output limits, load capability, noise, temperature grade, and qualification before production release.

Comparaison avec les alternatives

Paramètre Ce produit LM358DT LM358D LM358A LM2904DR RC4558DR
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC option 8-SOIC 8-SOIC
Brand STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments onsemi Texas Instruments
Number of Amplifiers 2 circuits 2 circuits 2 circuits Dual 2 circuits 2 circuits
Number of Channels 2 2 2 2 2 2

Principaux différenciateurs

  • Higher published bandwidth than the TI LM358A candidate (vs LM358A)
  • Confirmed 70 °C operating-temperature ceiling (vs RC4558DR)
  • Dual amplifier integration in a compact package (vs LM2904DR)

Notes de conception

Place the supply bypass capacitor immediately beside the LM358AWDT power pin and connect it to the device ground reference with a short path. Keep each feedback loop compact and route the noninverting input away from supply, output, and switching-node traces. This is especially important in sensor-conditioning circuits because long, high-impedance input routes can couple noise directly into the amplified output.

Do not assume that two amplifiers in one package may share arbitrary output and input loads. Check each amplifier’s output-current capability, load impedance, output-swing range, and stability conditions in the manufacturer datasheet. The 70 °C maximum operating temperature must also be compared with the highest expected PCB or enclosure temperature rather than only the nominal ambient condition.

Use a single defined analog ground return for the sensor, amplifier, and downstream converter rather than routing external load current through the IC ground pin. Ground bounce caused by shared return paths can look like input offset and can couple one channel into the other. Where the circuit requires isolation, follow the manufacturer’s grounding and decoupling recommendations and verify the assembled board with appropriate instrumentation.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

No explicit compliance declarations for the exact LM358AWDT suffix were established in the retrieved product and cross-reference records. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and AEC-Q100 status from the current manufacturer product documentation before qualification.

Recherches associées

LM358AWDT datasheet LM358AWDT datasheet pdf LM358AWDT pinout LM358AWDT specifications LM358AWDT price LM358AWDT stock STMicroelectronics LM358AWDT LM358AWDT equivalent LM358AWDT replacement LM358AWDT vs LM358DT LM358AWDT vs LM358A LM358AWDT SOIC-8 footprint LM358AWDT application circuit LM358AWDT 1.1 MHz op amp

Composants & termes associés

STMicroelectronics LM358AWDT LM358DT LM358D Texas Instruments LM358A onsemi LM2904DR RC4558DR dual operational amplifier operational amplifier analog integrated circuit signal conditioning voltage amplifier feedback unity-gain bandwidth input offset voltage common-mode input range output voltage swing low-power amplifier 8-SOIC SOIC package family surface-mount package industrial instrumentation sensor signal conditioning
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ