Texas Instruments

LM393MX/NOPB - Dual Open-Collector Comparator | Texas Instruments

MPN: LM393MX/NOPB ✓ نشط
2 V to 36 V Vdss 25 nA typical Id SOIC (D), 8 pins Package
الحد الأدنى للطلب: 1 |

LM393MX/NOPB نظرة عامة

Texas Instruments LM393MX/NOPB is a low-power, low-offset-voltage dual differential comparator with two independent comparison channels, open-collector outputs, and an 8-pin SOIC (D) package. It operates from a single supply or split supplies within a 2 V to 36 V total operating range. The device provides a typical response time of 1.3 us, offset voltage as low as 2.0 mV maximum, and typical input bias current of 25 nA.

A comparator is a semiconductor circuit that compares two input voltages and changes its output when the difference between them crosses a defined threshold. The LM393 family belongs to the broader analog IC and signal-conditioning hierarchy. Its open-collector outputs can sink logic-level current and require an external pull-up resistor, making the device useful for interfacing with TTL, CMOS, DTL, ECL, and MOS logic systems.

The LM393MX/NOPB combines two independent comparators in one package. Maximum input offset voltage is 2.0 mV for the indicated family specification, while the typical input bias current is 25 nA. A response time of 1.3 us is suitable for threshold detection, supervision, and signal conversion rather than high-speed waveform comparison. The open-collector architecture also provides wired-AND behavior when multiple outputs share a pull-up resistor.

Operation from a single supply supports industrial and embedded systems with 2 V to 36 V supply capability, while split-supply operation permits input signals near ground potential. Input common-mode range, output current limits, electrical characteristics by temperature, and detailed timing behavior should be confirmed against the Texas Instruments LM393 datasheet before final circuit sign-off.

Typical uses include battery monitoring, power-supply sequencing, overvoltage detection, sensor threshold conditioning, window comparison, and conversion of analog levels into digital logic. Because the outputs are open collector, each channel requires a pull-up resistor to the appropriate logic supply. The external pull-up also determines rise time, so it should be selected with the required logic speed and bus capacitance in mind.

For PCB design, place the pull-up resistor close to the output node and keep comparator inputs away from switching-current paths and high-speed digital edges. Check input and output absolute maximum ratings against the manufacturer's datasheet, especially in automotive or industrial environments where transients and supply variation may be significant. The LM393MX/NOPB is listed as active by Texas Instruments and is ordered in the 8-pin SOIC package for industrial and general-purpose comparison applications.

بدائل مباشرة لـ LM393MX/NOPB — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع LM393MX/NOPB (نفس عامل الشكل والبصمة) — يختلف في Operating Temperature Range, Package, Comparator Type, Response Time, Output Compatibility.

Texas Instruments
Operating Temperature Range: -40 °C to +125 °C
Package: 8-pin SOIC
Comparator Type: Dual differential comparator
Texas Instruments
Operating Temperature Range: 0 C to +70 C
Package: 8-SOIC
Comparator Type: Dual differential comparator
Texas Instruments
Operating Temperature Range: 0 °C to +70 °C
Package: SOIC-8 (D), 3.90 mm body width
Response Time: 1.3 µs (typical)
Texas Instruments
Operating Temperature Range: 0 °C to 70 °C
Package: 8-pin SOIC (D), 3.90 mm width
Comparator Type: Dual differential voltage comparator
Texas Instruments
Operating Temperature Range: 0°C to +70°C
Package: 8-SOIC
Comparator Type: Standard (General Purpose)

LM393MX

✅ بديل مباشر
Texas Instruments
📦 SOIC-8 (D)
Standard (General Purpose) · 2 · Open-Collector · Rail-to-Rail · 2 V to 36 V · 1 mA · 1.3 µs · 8-SOIC

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393M/NOPB

✅ بديل مباشر
Texas Instruments
📦 SOIC-8 (D)
Dual differential voltage comparator · 2 · Open-collector · 2.0 mV maximum · 0 °C to 70 °C

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393ADR

✅ بديل مباشر
Texas Instruments
📦 SOIC-8 (D)
Dual differential comparator · 2 channels · Open collector · Includes ground · -38 V to +38 V · TTL, MOS, and CMOS · Commercial grade · 8-SOIC

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393DR

✅ بديل مباشر
Texas Instruments
📦 SOIC-8 (D)
Texas Instruments · LM393DR · Dual Differential Comparator · 2 · Open-Collector · 2 V to 36 V · ±1 V to ±18 V · 1 mV

✗ غير متوفر

$0.11 / وحدة

عرض ورقة البيانات ←

LM2903DR

✅ بديل مباشر
Texas Instruments
📦 SOIC-8 (D)
Dual differential comparator · 2 channels · 2 V to 36 V · Open-collector · 300 ns · 8-pin SOIC · Surface mount · -40 °C to +125 °C

تواصل لمعرفة السعر

عرض ورقة البيانات ←

LM393MX/NOPB الحدود القصوى والخصائص الكهربائية

Comparator Type Low-power, low-offset-voltage dual differential comparator
Number of Comparators 2 independent channels
نوع الخرج Open collector
Supply Voltage Range 2 V to 36 V
Single-Supply Operation Supported
Split-Supply Operation Supported
Response Time 1.3 us
Input Offset Voltage 2.0 mV maximum
Input Bias Current 25 nA typical
تيار التغذية 1 mA
العلبة SOIC (D), 8 pins
Package Height 1.45 mm maximum
Package Width 3.9 mm to 4.5 mm
نطاق درجة حرارة التشغيل 0 C to 70 C
نوع التركيب Surface mount
Output Compatibility CMOS, DTL, ECL, MOS, and TTL logic

دليل تكوين أطراف LM393MX/NOPB 3.9 mm to 4.5 mm

تكوين الأطراف لـ LM393MX/NOPB (حزمة 3.9 mm to 4.5 mm). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.

مخطط توزيع أطراف حزمة 3.9 mm to 4.5 mm لـ LM393MX/NOPB

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM393MX/NOPB.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

LM393MX/NOPB مناسب لـ 6 التطبيقs: Battery Voltage Monitoring, Power-Supply Sequencing, Overvoltage and Undervoltage Protection, Sensor Threshold Conditioning, Industrial Limit Detection, Open-Collector Logic Interfacing.

⚡

Battery Voltage Monitoring

The LM393MX/NOPB is suitable for detecting a battery pack's transition between normal, undervoltage, and overvoltage conditions. Its 2 V to 36 V operating supply range accommodates many industrial battery systems, while offset voltage as low as 2.0 mV maximum helps separate closely spaced thresholds. Each independent comparator channel can monitor one limit, and its open-collector output can directly drive an enable, charger-state, or fault input when an appropriate pull-up is added. Because the output is open collector, the pull-up voltage defines the logic-high level and should match the monitored controller. The input signals must remain within the datasheet common-mode range, and a protected input divider should limit fault energy during charging transients.

⚡

Power-Supply Sequencing

LM393MX/NOPB can supervise several supply rails and generate discrete power-sequencing or power-good signals. The two independent channels allow two thresholds to be compared, while the 1.3 us response time is suitable for settling events that do not require sub-microsecond response. Each open-collector output can pull down a control node or shared wired-AND fault bus. A pull-up resistor should be placed close to the logic input being controlled to minimize bus rise time. In a multi-rail design, verify the common-mode limits, supply sequencing tolerances, and output behavior during power-off. The 2 V to 36 V operating range provides flexibility across low-voltage logic and higher-voltage industrial rails.

🏭

Overvoltage and Undervoltage Protection

The LM393MX/NOPB is useful for window or discrete overvoltage and undervoltage protection because it provides two independent differential comparison channels. With a 2.0 mV maximum offset specification in the indicated family description, it can resolve narrow threshold differences, while the typical 25 nA input bias current reduces error caused by high-impedance divider networks. Connect each channel to a reference and sensed voltage, then use its open-collector output to disable a downstream circuit or assert a fault signal. External pull-up resistors establish the active-high or active-low fault polarity. The input network should include appropriate limiting resistance, and transient protection should be selected so that fault conditions do not exceed the comparator's absolute maximum ratings.

🧩

Sensor Threshold Conditioning

LM393MX/NOPB can convert an analog sensor level into a logic event when the signal crosses a preset threshold. A reference voltage is applied to one input and the sensor signal to the other, with the two independent channels available for different sensor or threshold assignments. The 1.3 us response time is adequate for many temperature, light, pressure, and industrial level sensors, and the typical 25 nA input bias current is useful when the sensing network has high source impedance. The open-collector output can drive a pull-up-connected microcontroller input, gate, or relay-control stage. Keep the sensing node away from switching-current paths and confirm that the common-mode input range covers the complete sensor and temperature range.

🏭

Industrial Limit Detection

The LM393MX/NOPB fits industrial limit-detection circuits where a measurement must be translated into a high or low state for a controller. Its 2 V to 36 V operating supply range supports equipment using multiple logic levels, and its 1.3 us response time handles process variables without requiring a high-speed comparator. The two channels operate independently, allowing one part to monitor two limits or one limit in a redundant arrangement. Open-collector outputs permit wired-AND fault reporting when connected to a common pull-up node. Industrial implementations should include input filtering against motor and relay transients, maintain short ground-return paths, and verify temperature, common-mode, and output-current limits against the manufacturer datasheet.

🔧

Open-Collector Logic Interfacing

LM393MX/NOPB is particularly useful when an analog decision must be presented to TTL, CMOS, DTL, ECL, MOS, or other logic-family circuitry. The open-collector output can sink the required logic current, and an external pull-up resistor connects the output to the receiving system's supply voltage. This architecture also permits wired-AND behavior, allowing several comparator channels to share one pull-up node and signal a fault if any channel asserts low. The output's finite transition speed and pull-up-generated rise time must be included in interface timing. Place the pull-up close to the receiver or bus, use a resistor value appropriate for the required rise time, and check the device's output sink-current limit before adding multiple loads.

What are the key specifications of LM393MX/NOPB that engineers should know?
The LM393MX/NOPB is a dual, open-collector comparator in an 8-pin SOIC package. According to the Texas Instruments manufacturer datasheet, the device supports a 2 V to 36 V supply range, has a 1.3 us response time, offset voltage as low as 2.0 mV maximum, and typical input bias current of 25 nA. The two channels operate independently, and each open-collector output requires an external pull-up resistor.
Where can I download the LM393MX/NOPB datasheet PDF?
The official LM393MX/NOPB product and datasheet information is available from the Texas Instruments product page at https://www.ti.com/product/LM393-N/part-details/LM393MX/NOPB. The manufacturer datasheet is the preferred document for the complete pin description, absolute maximum ratings, electrical characteristics, typical curves, and application guidance. Third-party mirror pages may reproduce an older PDF, but the TI page should be used to confirm the current device documentation.
What is the LM393MX/NOPB?
The LM393MX/NOPB is a low-power, low-offset-voltage dual differential comparator made by Texas Instruments. According to the Texas Instruments manufacturer datasheet, each channel compares two input voltages and controls an open-collector output. The IC operates from 2 V to 36 V, provides a typical response time of 1.3 us, and comes in an 8-pin SOIC package for surface-mount industrial and general-purpose designs.
What is the supply voltage range of LM393MX/NOPB?
The LM393MX/NOPB operates from 2 V to 36 V. According to the Texas Instruments manufacturer datasheet, it can be powered from a single supply or from split supplies. This wide range allows the comparator to serve low-voltage logic systems and higher-voltage industrial control circuits, although the input and output absolute maximum ratings must remain respected during transients.
Why does LM393MX/NOPB need a pull-up resistor?
Each LM393MX/NOPB output is open collector, so it can pull the output node low but cannot actively drive it high. A pull-up resistor connected to the desired logic supply establishes the high state. According to the Texas Instruments manufacturer datasheet, the resulting rise time depends on the resistor value and total capacitance at the output, so faster logic may require a lower pull-up resistance.
What can replace the LM393MX/NOPB?
The LM393MX and LM393M/NOPB are direct same-footprint choices for an LM393MX/NOPB redesign, while the LM393 family variants such as LM393ADR and LM393DR use the same 8-pin SOIC format. According to Texas Instruments comparison information, LM393MX/NOPB is an active part with an 8-pin SOIC package. Confirm pin functions, electrical limits, temperature range, and qualification status before treating any alternative as a drop-in replacement.
Is LM393MX/NOPB the same as LM393MX?
The LM393MX/NOPB and LM393MX belong to the same LM393-N family and are listed in the 8-pin SOIC configuration, but their ordering suffixes can identify different labeling or compliance configurations. According to Texas Instruments product information, both families use the same general dual-comparator architecture. A formal replacement still requires checking the pinout, temperature grade, package dimensions, and purchasing configuration for the exact suffix.
What is the best Texas Instruments equivalent for LM393MX/NOPB?
The LM393MX is the closest same-manufacturer ordering option identified for LM393MX/NOPB because both belong to the LM393-N series and use an 8-pin SOIC package. According to the Texas Instruments product information, LM393MX/NOPB is active. Treat LM393MX as the leading alternative only after confirming that its suffix, temperature grade, labeling requirements, and electrical characteristics match the original design.
When should I choose LM393MX/NOPB over LM393M/NOPB?
Choose LM393MX/NOPB when the BOM must specifically use the LM393MX/NOPB ordering configuration or its associated labeling and compliance identity. Choose LM393M/NOPB when that suffix is approved for the product and its ordering identity matches the purchasing requirement. According to the Texas Instruments manufacturer datasheet, both are members of the same low-power, low-offset-voltage dual-comparator family, so the decision should focus on configuration rather than basic comparator function.
Is LM393MX/NOPB suitable for battery and power-supply monitoring?
Yes, LM393MX/NOPB is suitable for many battery and power-supply threshold-monitoring circuits. According to the Texas Instruments manufacturer datasheet, the device supports a 2 V to 36 V supply range, has input offset voltage as low as 2.0 mV maximum, and offers a 1.3 us response time. These characteristics support accurate threshold decisions, although the monitored signal must remain inside the specified common-mode range.
How does LM393MX/NOPB compare with LM393ADR?
The LM393MX/NOPB and LM393ADR are members of the same Texas Instruments LM393-N dual-comparator family and are available in an 8-pin SOIC package. The principal difference is the ordering and device configuration associated with each suffix rather than the basic dual open-collector function. According to Texas Instruments comparison data, both parts support low-power operation; use the exact manufacturer ordering information to confirm temperature grade, marking, and production status.
Where can I buy LM393MX/NOPB and check its lead time?
Use the Request a Quote form on this page to request LM393MX/NOPB price, stock confirmation, and current lead time. The manufacturer lists LM393MX/NOPB as active in the LM393-N family, with an 8-pin SOIC package and a 0 C to 70 C operating range. Current commercial availability and delivery scheduling should be confirmed for the exact ordering suffix and production quantity.
What is the price of LM393MX/NOPB?
Use the Request a Quote form on this page for a current LM393MX/NOPB quotation. According to the Texas Instruments product information, the part is active and is ordered as an 8-pin SOIC device with a 0 C to 70 C operating range. The quotation should reflect the requested quantity, date code, and packaging configuration, which determine commercial terms and availability.
Is LM393MX/NOPB in stock and how long is the lead time?
LM393MX/NOPB is listed as active by Texas Instruments, but current stock and lead time should be confirmed through the Request a Quote form on this page. According to the Texas Instruments product information, the device is an 8-pin SOIC comparator with a 0 C to 70 C operating range. Supply status can vary with quantity and date code, so do not base a production schedule on a generic catalog indication.
Where can I find the LM393MX/NOPB pinout?
Use the pin-description table and package drawing in the Texas Instruments LM393 manufacturer datasheet. The LM393MX/NOPB is an 8-pin SOIC device, but the public search excerpts do not reproduce a verified pin-by-pin diagram. The datasheet pin table is therefore the controlling reference for assigning input, output, supply, and ground connections during schematic capture and PCB layout.
What are the main design limitations of LM393MX/NOPB?
The principal limitations of LM393MX/NOPB are the open-collector output requirement, finite 1.3 us response time, and input common-mode restrictions that must be followed from the datasheet. According to the Texas Instruments manufacturer datasheet, the offset voltage can be as low as 2.0 mV maximum and input bias current is typically 25 nA. Add suitable pull-up resistors and verify that transient, temperature, and supply conditions remain within the electrical limits.

بيانات مرجعية هندسية لـ LM393MX/NOPB — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose LM393MX/NOPB when the design requires an active, low-power, open-collector dual comparator in an 8-pin SOIC package and the exact ordering configuration is approved by the product requirements. Its 2 V to 36 V operating range, 2.0 mV maximum offset specification, 25 nA typical input bias current, and 1.3 us response time suit threshold detection, battery supervision, power sequencing, and sensor conditioning rather than high-speed waveform comparison. LM393MX is the closest same-family ordering alternative, while LM393M/NOPB, LM393ADR, and LM393DR provide closely related LM393 configurations. LM2903DR is preferable when a wider automotive temperature grade is required. For every alternative, confirm the exact pinout, electrical limits, temperature range, qualification status, and suffix-specific production details before release. Because all options use open-collector outputs, each design still requires correctly selected pull-up resistors and protection for transients and out-of-range input conditions.

المقارنة مع البدائل

المعامل هذا المنتج LM393MX LM393M/NOPB LM393ADR LM393DR LM2903DR
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOIC-8 (D) SOIC-8 (D) SOIC-8 (D) SOIC-8 (D) SOIC-8 (D) SOIC-8 (D)
Comparator Configuration Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator Dual differential comparator
Output Type Open collector Open collector Open collector Open collector Open collector Open collector
Supply Voltage Range 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V 2 V to 36 V

أبرز الفروقات

  • Two independent comparator channels in one compact package (مقابلLM393MX)
  • Low-offset threshold detection (مقابلLM393M/NOPB)
  • Wide operating supply range (مقابلLM2903DR)

ملاحظات التصميم

Do not treat an open-collector output as a push-pull logic output. Each channel needs a pull-up resistor connected to the supply used by the receiving logic. Choose the resistor to satisfy the required rise time and sink-current limit: the output discharges the node capacitance with the pull-up resistor, so a very large resistor slows the rising edge while a very small resistor increases the current required when the output is low.

Keep the two input networks and the ground reference close to the SOIC pins. High-value dividers can be sensitive to leakage and surface contamination, particularly with a typical input bias current of 25 nA. Route sensed signals away from switching nodes, relay coils, inductors, and high-current return paths. Place the output pull-up near the receiving input or bus so that the open-collector node does not become a long antenna-like trace.

Confirm that the supply voltage remains between 2 V and 36 V during startup, shutdown, and normal operation. The 1.3 us response time is adequate for threshold and supervision functions but not for high-speed pulse or edge detection. Also verify that the common-mode voltage at both inputs stays inside the manufacturer limits throughout the operating temperature range, especially when a 2 V supply is used.

Input offset voltage can shift the apparent switching threshold. A maximum of 2.0 mV is meaningful for precise sensing, but it must be included in error budgets together with reference tolerance, resistor tolerance, input bias effects, and temperature drift. For precision thresholding, use a stable reference, suitable resistor tolerances, and an input network that does not convert leakage into excessive voltage error.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The Texas Instruments product information identifies LM393MX/NOPB as an active 8-pin SOIC device. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not present in the cited excerpts.

تم التحقق من البيانات في: 2026-11-09 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

lm393mx nopb lm393mx datasheet LM393MX/NOPB datasheet LM393MX/NOPB pinout LM393MX/NOPB specifications LM393MX/NOPB SOIC-8 LM393MX/NOPB equivalent LM393MX/NOPB replacement LM393MX/NOPB voltage comparator LM393MX/NOPB open collector LM393MX/NOPB battery monitoring LM393MX/NOPB price Texas Instruments LM393MX/NOPB

المكونات والمصطلحات ذات الصلة

Texas Instruments LM393MX/NOPB LM393MX LM393M/NOPB LM393ADR LM393DR LM2903DR LM393-N dual differential comparator comparator analog integrated circuit signal conditioning open-collector output wired-AND logic input offset voltage input bias current common-mode voltage supply voltage SOIC-8 surface mount battery monitoring power sequencing industrial limit detection sensor threshold conditioning
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر