LM393MX/NOPB - Dual Open-Collector Comparator | Texas Instruments
N.º de pieza: LM393MX/NOPB ✓ ActivoLM393MX/NOPB Descripción general
A comparator is a semiconductor circuit that compares two input voltages and changes its output when the difference between them crosses a defined threshold. The LM393 family belongs to the broader analog IC and signal-conditioning hierarchy. Its open-collector outputs can sink logic-level current and require an external pull-up resistor, making the device useful for interfacing with TTL, CMOS, DTL, ECL, and MOS logic systems.
The LM393MX/NOPB combines two independent comparators in one package. Maximum input offset voltage is 2.0 mV for the indicated family specification, while the typical input bias current is 25 nA. A response time of 1.3 us is suitable for threshold detection, supervision, and signal conversion rather than high-speed waveform comparison. The open-collector architecture also provides wired-AND behavior when multiple outputs share a pull-up resistor.
Operation from a single supply supports industrial and embedded systems with 2 V to 36 V supply capability, while split-supply operation permits input signals near ground potential. Input common-mode range, output current limits, electrical characteristics by temperature, and detailed timing behavior should be confirmed against the Texas Instruments LM393 datasheet before final circuit sign-off.
Typical uses include battery monitoring, power-supply sequencing, overvoltage detection, sensor threshold conditioning, window comparison, and conversion of analog levels into digital logic. Because the outputs are open collector, each channel requires a pull-up resistor to the appropriate logic supply. The external pull-up also determines rise time, so it should be selected with the required logic speed and bus capacitance in mind.
For PCB design, place the pull-up resistor close to the output node and keep comparator inputs away from switching-current paths and high-speed digital edges. Check input and output absolute maximum ratings against the manufacturer's datasheet, especially in automotive or industrial environments where transients and supply variation may be significant. The LM393MX/NOPB is listed as active by Texas Instruments and is ordered in the 8-pin SOIC package for industrial and general-purpose comparison applications.
Alternativas directas para LM393MX/NOPB — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con LM393MX/NOPB (mismo factor de forma y huella) — difiere en Operating Temperature Range, Package, Comparator Type, Response Time, Output Compatibility.
LM393MX
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393M/NOPB
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393ADR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393DR
✅ Sustitución directa✗ Sin stock
$0.11 / unidad
Ver hoja de datos →LM2903DR
✅ Sustitución directaConsulte el precio
Ver hoja de datos →LM393MX/NOPB Valores máximos y características eléctricas
| Comparator Type | Low-power, low-offset-voltage dual differential comparator |
| Number of Comparators | 2 independent channels |
| Tipo de salida | Open collector |
| Supply Voltage Range | 2 V to 36 V |
| Single-Supply Operation | Supported |
| Split-Supply Operation | Supported |
| Response Time | 1.3 us |
| Input Offset Voltage | 2.0 mV maximum |
| Input Bias Current | 25 nA typical |
| Corriente de alimentación | 1 mA |
| Encapsulado | SOIC (D), 8 pins |
| Package Height | 1.45 mm maximum |
| Package Width | 3.9 mm to 4.5 mm |
| Rango de temperatura de funcionamiento | 0 C to 70 C |
| Tipo de montaje | Surface mount |
| Output Compatibility | CMOS, DTL, ECL, MOS, and TTL logic |
Guía de configuración de pines de LM393MX/NOPB 3.9 mm to 4.5 mm
Configuración de pines para LM393MX/NOPB (encapsulado 3.9 mm to 4.5 mm). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para LM393MX/NOPB.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
LM393MX/NOPB es adecuado para 6 aplicacións: Battery Voltage Monitoring, Power-Supply Sequencing, Overvoltage and Undervoltage Protection, Sensor Threshold Conditioning, Industrial Limit Detection, Open-Collector Logic Interfacing.
Battery Voltage Monitoring
The LM393MX/NOPB is suitable for detecting a battery pack's transition between normal, undervoltage, and overvoltage conditions. Its 2 V to 36 V operating supply range accommodates many industrial battery systems, while offset voltage as low as 2.0 mV maximum helps separate closely spaced thresholds. Each independent comparator channel can monitor one limit, and its open-collector output can directly drive an enable, charger-state, or fault input when an appropriate pull-up is added. Because the output is open collector, the pull-up voltage defines the logic-high level and should match the monitored controller. The input signals must remain within the datasheet common-mode range, and a protected input divider should limit fault energy during charging transients.
Recomendado
Power-Supply Sequencing
LM393MX/NOPB can supervise several supply rails and generate discrete power-sequencing or power-good signals. The two independent channels allow two thresholds to be compared, while the 1.3 us response time is suitable for settling events that do not require sub-microsecond response. Each open-collector output can pull down a control node or shared wired-AND fault bus. A pull-up resistor should be placed close to the logic input being controlled to minimize bus rise time. In a multi-rail design, verify the common-mode limits, supply sequencing tolerances, and output behavior during power-off. The 2 V to 36 V operating range provides flexibility across low-voltage logic and higher-voltage industrial rails.
Recomendado
Overvoltage and Undervoltage Protection
The LM393MX/NOPB is useful for window or discrete overvoltage and undervoltage protection because it provides two independent differential comparison channels. With a 2.0 mV maximum offset specification in the indicated family description, it can resolve narrow threshold differences, while the typical 25 nA input bias current reduces error caused by high-impedance divider networks. Connect each channel to a reference and sensed voltage, then use its open-collector output to disable a downstream circuit or assert a fault signal. External pull-up resistors establish the active-high or active-low fault polarity. The input network should include appropriate limiting resistance, and transient protection should be selected so that fault conditions do not exceed the comparator's absolute maximum ratings.
Recomendado
Sensor Threshold Conditioning
LM393MX/NOPB can convert an analog sensor level into a logic event when the signal crosses a preset threshold. A reference voltage is applied to one input and the sensor signal to the other, with the two independent channels available for different sensor or threshold assignments. The 1.3 us response time is adequate for many temperature, light, pressure, and industrial level sensors, and the typical 25 nA input bias current is useful when the sensing network has high source impedance. The open-collector output can drive a pull-up-connected microcontroller input, gate, or relay-control stage. Keep the sensing node away from switching-current paths and confirm that the common-mode input range covers the complete sensor and temperature range.
Recomendado
Industrial Limit Detection
The LM393MX/NOPB fits industrial limit-detection circuits where a measurement must be translated into a high or low state for a controller. Its 2 V to 36 V operating supply range supports equipment using multiple logic levels, and its 1.3 us response time handles process variables without requiring a high-speed comparator. The two channels operate independently, allowing one part to monitor two limits or one limit in a redundant arrangement. Open-collector outputs permit wired-AND fault reporting when connected to a common pull-up node. Industrial implementations should include input filtering against motor and relay transients, maintain short ground-return paths, and verify temperature, common-mode, and output-current limits against the manufacturer datasheet.
Recomendado
Open-Collector Logic Interfacing
LM393MX/NOPB is particularly useful when an analog decision must be presented to TTL, CMOS, DTL, ECL, MOS, or other logic-family circuitry. The open-collector output can sink the required logic current, and an external pull-up resistor connects the output to the receiving system's supply voltage. This architecture also permits wired-AND behavior, allowing several comparator channels to share one pull-up node and signal a fault if any channel asserts low. The output's finite transition speed and pull-up-generated rise time must be included in interface timing. Place the pull-up close to the receiver or bus, use a resistor value appropriate for the required rise time, and check the device's output sink-current limit before adding multiple loads.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para LM393MX/NOPB — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | LM393MX | LM393M/NOPB | LM393ADR | LM393DR | LM2903DR |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) | SOIC-8 (D) |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open collector | Open collector | Open collector | Open collector | Open collector | Open collector |
| Supply Voltage Range | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V | 2 V to 36 V |
Diferenciadores clave
- Two independent comparator channels in one compact package (frente a LM393MX)
- Low-offset threshold detection (frente a LM393M/NOPB)
- Wide operating supply range (frente a LM2903DR)
Notas de diseño
Do not treat an open-collector output as a push-pull logic output. Each channel needs a pull-up resistor connected to the supply used by the receiving logic. Choose the resistor to satisfy the required rise time and sink-current limit: the output discharges the node capacitance with the pull-up resistor, so a very large resistor slows the rising edge while a very small resistor increases the current required when the output is low.
Keep the two input networks and the ground reference close to the SOIC pins. High-value dividers can be sensitive to leakage and surface contamination, particularly with a typical input bias current of 25 nA. Route sensed signals away from switching nodes, relay coils, inductors, and high-current return paths. Place the output pull-up near the receiving input or bus so that the open-collector node does not become a long antenna-like trace.
Confirm that the supply voltage remains between 2 V and 36 V during startup, shutdown, and normal operation. The 1.3 us response time is adequate for threshold and supervision functions but not for high-speed pulse or edge detection. Also verify that the common-mode voltage at both inputs stays inside the manufacturer limits throughout the operating temperature range, especially when a 2 V supply is used.
Input offset voltage can shift the apparent switching threshold. A maximum of 2.0 mV is meaningful for precise sensing, but it must be included in error budgets together with reference tolerance, resistor tolerance, input bias effects, and temperature drift. For precision thresholding, use a stable reference, suitable resistor tolerances, and an input network that does not convert leakage into excessive voltage error.
Información de cumplimiento
The Texas Instruments product information identifies LM393MX/NOPB as an active 8-pin SOIC device. Explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not present in the cited excerpts.