MC33662SEF - LIN Bus Transceiver, 100 kbps, SOIC-8 | NXP
MPN: MC33662SEF ✓ نشطMC33662SEF نظرة عامة
A LIN, or Local Interconnect Network, transceiver is an interface IC that connects a host microcontroller to a low-speed vehicle-network bus. The LIN bus hierarchy sits below more complex in-vehicle networks and is commonly used for body electronics, lighting, door modules, climate controls, seat controls, and other distributed vehicle functions. The MC33662SEF translates digital logic levels between the host processor and the physical LIN network, allowing the processor to exchange commands and sensor information with remote nodes.
The MC33662SEF is identified as a single-channel, 1/1 LIN transceiver with a maximum stated bus speed of 100 kbps. This speed suits LIN nodes that exchange relatively small control payloads rather than high-bandwidth data. The 13.5 V operating-supply figure places the device in an automotive-style electrical environment and helps engineers evaluate its relationship to vehicle battery and regulated power rails. Its interface role should be reviewed together with the MCU supply level, transceiver enable strategy, bus termination, and protection requirements of the target vehicle platform.
The 8-SOIC package is the primary assembly constraint when planning a replacement or footprint comparison. Pin assignment, exposed-pad requirements, logic thresholds, sleep behavior, bus polarity, and transceiver operating mode must all be checked before substituting another part. The SOT96 package designation associated with the MC33662 family in comparison listings should not be confused with the SOIC-8 outline identified for MC33662SEF; package dimensions and land patterns are decisive in a drop-in review.
Typical LIN applications include automotive door modules, body-control units, seat and climate-control modules, lighting controllers, sensor interfaces, and compact actuator nodes. The MC33662SEF is most appropriate when a new design needs a 100 kbps LIN physical interface and can use the specified SOIC-8 footprint. In a mixed technology vehicle, it can connect a conventional microcontroller to LIN subnets without introducing a high-speed communications transceiver.
For PCB implementation, place the transceiver close to the connector or protected LIN trace, keep the bus path away from sensitive analog and high-speed digital routing, and provide the required local decoupling. Review the manufacturer datasheet for the exact input and output pin functions, logical enable polarity, sleep-mode behavior, and external component requirements. Those details determine whether a candidate part is a true pin-to-pin replacement rather than only a similar LIN transceiver.
This product page combines the identifiable MC33662SEF device data, package and speed information, same-family replacement evidence, application guidance, and a focused engineering comparison framework. It highlights what can be confirmed for the exact ordered part and directs designers to the manufacturer datasheet for authoritative connection details, electrical limits, and implementation requirements.
بدائل مباشرة لـ MC33662SEF — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MC33662SEF (نفس عامل الشكل والبصمة) — يختلف في Package, Product Type.
MC33662BSEF
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
MC33662SEF المواصفات
| Product Type | 1/1 LIN bus transceiver |
| LIN Channel Count | 1 channel |
| Bus Interface | LIN bus |
| Maximum Stated Data Rate | 100 kbps |
| Operating Supply | 13.5 V |
| Automotive Application | Yes |
| العلبة | 8-SOIC, 0.154 in (3.90 mm) width |
| عدد الأطراف | 8 pins |
| نوع التركيب | Surface mount |
| Manufacturer | NXP Semiconductors |
| Original Manufacturer | Freescale Semiconductor |
| Device Classification | Transceiver, half |
| Sleep Mode | Supported |
دليل تكوين أطراف MC33662SEF 8-soic, 0.154 in (3.90 mm) width
تكوين الأطراف لـ MC33662SEF (حزمة 8-soic, 0.154 in (3.90 mm) width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MC33662SEF.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MC33662SEF مناسب لـ 6 التطبيقs: Automotive Door Control Module, Climate-Control Body Module, Seat and Lighting Controller, Automotive Sensor Interface, Compact Vehicle Actuator Node, Body Electronics Gateway.
Automotive Door Control Module
The MC33662SEF provides the physical interface for a LIN-connected door control node operating at up to 100 kbps. A host MCU or LIN-capable controller can use the single transceiver channel for communication with switches, latch actuators, position sensors, and related body electronics. Its stated 13.5 V operating supply fits automotive power-system environments, while the 8-SOIC package supports conventional surface-mount assembly. The design should verify logic-level compatibility, wake-up behavior, and external bus protection against the manufacturer datasheet.
موصى به
Climate-Control Body Module
A climate-control module can use the MC33662SEF as a 100 kbps LIN physical-layer endpoint for remote temperature sensors, fan commands, and actuator control. The single-channel 1/1 arrangement is appropriate when the module needs one LIN subnet interface and a separate controller handles frame timing and diagnostic behavior. The 8-SOIC outline helps preserve a conventional footprint, but the MCU interface voltage and sleep-mode logic must be confirmed before schematic release.
موصى به
Seat and Lighting Controller
The MC33662SEF is suitable for distributed seat, lighting, and switch modules that exchange low-bandwidth commands over LIN. Its stated 100 kbps rate matches the network class commonly used for body-control nodes, allowing a host processor to monitor switches and coordinate motors or lamps without relying on a higher-bandwidth bus transceiver. The 13.5 V operating supply is an important matching point, while wiring protection and automotive qualification requirements must be addressed at the system level.
موصى به
Automotive Sensor Interface
The MC33662SEF can connect a vehicle sensor or compact actuator node to a LIN bus running at up to 100 kbps. This arrangement is useful where multiple small sensors share a bus and the application needs robust wired communication over a lower-cost network. The MCU must implement the LIN protocol and diagnostic behavior because the MC33662SEF provides the physical transceiver layer. Its 8-SOIC package and single-channel architecture simplify compact module layouts.
موصى به
Compact Vehicle Actuator Node
A compact actuator node can use the MC33662SEF to receive commands from a central LIN controller and return status information at up to 100 kbps. The device's single LIN channel is well matched to a dedicated endpoint with one network connection. The design must account for the actuator's supply transients, ground-bounce conditions, connector protection, and transceiver sleep current. The manufacturer datasheet should define the logic thresholds and mode-control behavior used by the host controller.
موصى به
Body Electronics Gateway
The MC33662SEF can serve as a LIN endpoint within a body-electronics gateway that coordinates distributed vehicle accessories. At 100 kbps, it is intended for supervisory commands, switch states, and sensor readings rather than bulk data transfer. The 13.5 V stated supply and 8-SOIC assembly align with the operating environment and manufacturing style of automotive control boards. For production use, validate bus fault recovery, wake-up behavior, and transient protection with the complete wiring harness.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MC33662SEF — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | MC33662BSEF |
|---|---|---|
| Package | 8-SOIC, 0.154 in (3.90 mm) width | Package reported consistent with MC33662SEF |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Transceiver Configuration | 1/1 LIN transceiver | Reported consistent principal characteristics |
| Automotive Application | Yes | Automotive |
| Pin and Terminal Compatibility | 8-SOIC reference design | Terminals and package reported consistent |
أبرز الفروقات
- Exact orderable device with a defined automotive LIN application (مقابلMC33662BSEF)
- Single-channel LIN interface for distributed vehicle nodes (مقابلMC33662BSEF)
- Established SOIC-8 assembly footprint (مقابلMC33662BSEF)
ملاحظات التصميم
Place the MC33662SEF near the LIN connector or protected bus entry point and keep the LIN trace short and isolated from sensitive analog or high-speed digital routes. Provide local supply decoupling at the device pins using the capacitor values and layout shown in the manufacturer datasheet. The 8-SOIC footprint is not interchangeable with the legacy SOT96 designation mentioned in some comparison records, so verify land-pattern dimensions against the package drawing before PCB release.
Do not approve a replacement based only on the phrase LIN transceiver. Confirm pin numbering, logic-side signals, enable and sleep polarity, supply limits, bus output behavior, and package dimensions. The MC33662BSEF is reported as completely replaceable, but qualification and orderable-suffix differences still require review. A substitution that matches 100 kbps LIN communication but differs in wake-up or mode-control logic may not be functionally drop-in.
The LIN bus cable and connector can introduce transient energy and radiated disturbance into a compact automotive control board. Use the interface, protection, and grounding arrangement specified in the manufacturer application guidance, and keep return-current paths short. Validate radiated-emission, conducted-immunity, transient, ground-offset, and bus-fault behavior on the completed module because a compliant transceiver alone does not establish compliance of the finished product.
معلومات الامتثال
The device is identified for automotive applications, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the available product records. Verify the current environmental and quality documentation before production release.