MC33662SEF - LIN Bus Transceiver, 100 kbps, SOIC-8 | NXP
部品番号: MC33662SEF ✓ 生産中MC33662SEF 概要
A LIN, or Local Interconnect Network, transceiver is an interface IC that connects a host microcontroller to a low-speed vehicle-network bus. The LIN bus hierarchy sits below more complex in-vehicle networks and is commonly used for body electronics, lighting, door modules, climate controls, seat controls, and other distributed vehicle functions. The MC33662SEF translates digital logic levels between the host processor and the physical LIN network, allowing the processor to exchange commands and sensor information with remote nodes.
The MC33662SEF is identified as a single-channel, 1/1 LIN transceiver with a maximum stated bus speed of 100 kbps. This speed suits LIN nodes that exchange relatively small control payloads rather than high-bandwidth data. The 13.5 V operating-supply figure places the device in an automotive-style electrical environment and helps engineers evaluate its relationship to vehicle battery and regulated power rails. Its interface role should be reviewed together with the MCU supply level, transceiver enable strategy, bus termination, and protection requirements of the target vehicle platform.
The 8-SOIC package is the primary assembly constraint when planning a replacement or footprint comparison. Pin assignment, exposed-pad requirements, logic thresholds, sleep behavior, bus polarity, and transceiver operating mode must all be checked before substituting another part. The SOT96 package designation associated with the MC33662 family in comparison listings should not be confused with the SOIC-8 outline identified for MC33662SEF; package dimensions and land patterns are decisive in a drop-in review.
Typical LIN applications include automotive door modules, body-control units, seat and climate-control modules, lighting controllers, sensor interfaces, and compact actuator nodes. The MC33662SEF is most appropriate when a new design needs a 100 kbps LIN physical interface and can use the specified SOIC-8 footprint. In a mixed technology vehicle, it can connect a conventional microcontroller to LIN subnets without introducing a high-speed communications transceiver.
For PCB implementation, place the transceiver close to the connector or protected LIN trace, keep the bus path away from sensitive analog and high-speed digital routing, and provide the required local decoupling. Review the manufacturer datasheet for the exact input and output pin functions, logical enable polarity, sleep-mode behavior, and external component requirements. Those details determine whether a candidate part is a true pin-to-pin replacement rather than only a similar LIN transceiver.
This product page combines the identifiable MC33662SEF device data, package and speed information, same-family replacement evidence, application guidance, and a focused engineering comparison framework. It highlights what can be confirmed for the exact ordered part and directs designers to the manufacturer datasheet for authoritative connection details, electrical limits, and implementation requirements.
ドロップイン代替品: MC33662SEF — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: MC33662SEF (同一形状・フットプリント) — 相違点: Package, Product Type.
MC33662BSEF
✅ ドロップイン📋 参考代替品(カタログ未掲載)
MC33662SEF 仕様
| Product Type | 1/1 LIN bus transceiver |
| LIN Channel Count | 1 channel |
| Bus Interface | LIN bus |
| Maximum Stated Data Rate | 100 kbps |
| Operating Supply | 13.5 V |
| Automotive Application | Yes |
| パッケージ | 8-SOIC, 0.154 in (3.90 mm) width |
| ピン数 | 8 pins |
| 実装タイプ | Surface mount |
| Manufacturer | NXP Semiconductors |
| Original Manufacturer | Freescale Semiconductor |
| Device Classification | Transceiver, half |
| Sleep Mode | Supported |
MC33662SEF 8-soic, 0.154 in (3.90 mm) width ピン配置ガイド
MC33662SEF (8-soic, 0.154 in (3.90 mm) width パッケージ) のピン配置。 ピン番号、機能、接続図はメーカーのデータシートで定義されています。正確なフットプリントとはんだ付けのガイドラインについては、データシートを参照してください。
詳細なピン配置データはありません: MC33662SEF.
詳細は データシート をご参照ください。
主な用途
MC33662SEF の用途: 6 件s: Automotive Door Control Module, Climate-Control Body Module, Seat and Lighting Controller, Automotive Sensor Interface, Compact Vehicle Actuator Node, Body Electronics Gateway.
Automotive Door Control Module
The MC33662SEF provides the physical interface for a LIN-connected door control node operating at up to 100 kbps. A host MCU or LIN-capable controller can use the single transceiver channel for communication with switches, latch actuators, position sensors, and related body electronics. Its stated 13.5 V operating supply fits automotive power-system environments, while the 8-SOIC package supports conventional surface-mount assembly. The design should verify logic-level compatibility, wake-up behavior, and external bus protection against the manufacturer datasheet.
おすすめ
Climate-Control Body Module
A climate-control module can use the MC33662SEF as a 100 kbps LIN physical-layer endpoint for remote temperature sensors, fan commands, and actuator control. The single-channel 1/1 arrangement is appropriate when the module needs one LIN subnet interface and a separate controller handles frame timing and diagnostic behavior. The 8-SOIC outline helps preserve a conventional footprint, but the MCU interface voltage and sleep-mode logic must be confirmed before schematic release.
おすすめ
Seat and Lighting Controller
The MC33662SEF is suitable for distributed seat, lighting, and switch modules that exchange low-bandwidth commands over LIN. Its stated 100 kbps rate matches the network class commonly used for body-control nodes, allowing a host processor to monitor switches and coordinate motors or lamps without relying on a higher-bandwidth bus transceiver. The 13.5 V operating supply is an important matching point, while wiring protection and automotive qualification requirements must be addressed at the system level.
おすすめ
Automotive Sensor Interface
The MC33662SEF can connect a vehicle sensor or compact actuator node to a LIN bus running at up to 100 kbps. This arrangement is useful where multiple small sensors share a bus and the application needs robust wired communication over a lower-cost network. The MCU must implement the LIN protocol and diagnostic behavior because the MC33662SEF provides the physical transceiver layer. Its 8-SOIC package and single-channel architecture simplify compact module layouts.
おすすめ
Compact Vehicle Actuator Node
A compact actuator node can use the MC33662SEF to receive commands from a central LIN controller and return status information at up to 100 kbps. The device's single LIN channel is well matched to a dedicated endpoint with one network connection. The design must account for the actuator's supply transients, ground-bounce conditions, connector protection, and transceiver sleep current. The manufacturer datasheet should define the logic thresholds and mode-control behavior used by the host controller.
おすすめ
Body Electronics Gateway
The MC33662SEF can serve as a LIN endpoint within a body-electronics gateway that coordinates distributed vehicle accessories. At 100 kbps, it is intended for supervisory commands, switch states, and sensor readings rather than bulk data transfer. The 13.5 V stated supply and 8-SOIC assembly align with the operating environment and manufacturing style of automotive control boards. For production use, validate bus fault recovery, wake-up behavior, and transient protection with the complete wiring harness.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: MC33662SEF — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | MC33662BSEF |
|---|---|---|
| Package | 8-SOIC, 0.154 in (3.90 mm) width | Package reported consistent with MC33662SEF |
| Brand | NXP Semiconductors | NXP Semiconductors |
| Transceiver Configuration | 1/1 LIN transceiver | Reported consistent principal characteristics |
| Automotive Application | Yes | Automotive |
| Pin and Terminal Compatibility | 8-SOIC reference design | Terminals and package reported consistent |
主な差別化要因
- Exact orderable device with a defined automotive LIN application (vs MC33662BSEF)
- Single-channel LIN interface for distributed vehicle nodes (vs MC33662BSEF)
- Established SOIC-8 assembly footprint (vs MC33662BSEF)
設計ノート
Place the MC33662SEF near the LIN connector or protected bus entry point and keep the LIN trace short and isolated from sensitive analog or high-speed digital routes. Provide local supply decoupling at the device pins using the capacitor values and layout shown in the manufacturer datasheet. The 8-SOIC footprint is not interchangeable with the legacy SOT96 designation mentioned in some comparison records, so verify land-pattern dimensions against the package drawing before PCB release.
Do not approve a replacement based only on the phrase LIN transceiver. Confirm pin numbering, logic-side signals, enable and sleep polarity, supply limits, bus output behavior, and package dimensions. The MC33662BSEF is reported as completely replaceable, but qualification and orderable-suffix differences still require review. A substitution that matches 100 kbps LIN communication but differs in wake-up or mode-control logic may not be functionally drop-in.
The LIN bus cable and connector can introduce transient energy and radiated disturbance into a compact automotive control board. Use the interface, protection, and grounding arrangement specified in the manufacturer application guidance, and keep return-current paths short. Validate radiated-emission, conducted-immunity, transient, ground-offset, and bus-fault behavior on the completed module because a compliant transceiver alone does not establish compliance of the finished product.
コンプライアンス情報
The device is identified for automotive applications, but no specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration was identified in the available product records. Verify the current environmental and quality documentation before production release.