MCP3422A3-E/MC - 18-Bit Dual-Channel Delta-Sigma ADC | Microchip
MPN: MCP3422A3-E/MC ✓ نشطMCP3422A3-E/MC نظرة عامة
An analog-to-digital converter, or ADC, converts continuous analog voltages into numeric values that a microcontroller or embedded system can process. The MCP3422 belongs to the delta-sigma ADC family, where an internal modulator and digital filter shape the conversion result with high resolution and good noise performance at relatively low sample rates. This two-channel device supports differential measurement, which helps reject common-mode noise when a sensor output is referenced to a nearby analog ground.
The MCP3422 family provides up to 18 bits of resolution and integrates a 2.048 V precision reference. Differential input capability and the internal reference reduce the need for external active balancing networks. The I2C interface also reduces the number of signal connections required between the converter and a host controller. Compared with general-purpose flash-based ADCs, the architecture is better suited to instrumentation, industrial monitoring, and slowly changing sensor signals rather than high-speed waveform capture.
The A3 designation identifies the speed grade within the MCP3422 family. The related MCP3422A3T-E/MS listing identifies this performance level as approximately 3.75 samples per second, making the A3 version appropriate for temperature, pressure, load-cell, and process-control measurements where low conversion throughput is acceptable. Differential measurements can also use the device's programmable gain behavior when the signal amplitude requires additional sensitivity.
Typical applications include bridge-based pressure and load measurements, current-shunt monitoring, precision temperature sensing, laboratory instrumentation, and factory automation. The 2 mm by 3 mm DFN package supports compact analog front ends, but the small thermal pad and exposed package structure require careful PCB layout and solder assembly. The 2.7 V to 5.5 V operating range also allows the converter to share supply arrangements with both 3.3 V and 5 V embedded systems.
When laying out this device, place input filtering and reference-decoupling components close to their associated pins, route the exposed pad into a thermal and ground plane, and keep digital I2C traces away from high-impedance differential inputs. Confirm the selected conversion speed against the required latency and noise trade-off, and use the manufacturer pin-description table when assigning PCB tracks and test points.
This page combines device specifications, package details, application guidance, design notes, and a structured comparison with related MCP3422 devices. It also highlights the differences between gain grades and package options so engineers can identify a compatible replacement without confusing an 8-pin DFN part with an MSOP or SOIC variant.
بدائل مباشرة لـ MCP3422A3-E/MC — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع MCP3422A3-E/MC (نفس عامل الشكل والبصمة) — يختلف في Package, Digital Interface, Differential Input Range, Input Architecture, Automotive Qualification.
MCP3422A0-E/MC
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MCP3422A2-E/MC
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MCP3422A6-E/MC
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MCP3422A3-E/SN
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←MCP3422A3-E/MC الحدود القصوى والخصائص الكهربائية
| ADC Type | Delta-sigma ADC |
| الدقة | 18 bits |
| Number of Channels | 2 channels |
| Input Type | Differential |
| الواجهة | I2C |
| Internal Reference Voltage | 2.048 V |
| Differential Input Range | -2.048 V to +2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V |
| نطاق درجة حرارة التشغيل | -40 °C to +125 °C |
| العلبة | 8-pin DFN (2 mm x 3 mm) |
| نوع التركيب | Surface mount |
| A3 Conversion Rate | 3.75 samples per second |
| On-Board Reference | Yes, 2.048 V precision reference |
| Automotive Qualification | AEC-Q100 grade indicated for the A3 family |
دليل تكوين أطراف MCP3422A3-E/MC 8-pin dfn (2 mm x 3 mm)
تكوين الأطراف لـ MCP3422A3-E/MC (حزمة 8-pin dfn (2 mm x 3 mm)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ MCP3422A3-E/MC.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
MCP3422A3-E/MC مناسب لـ 6 التطبيقs: Load-Cell and Weighing Systems, Precision Pressure and Process Monitoring, RTD and Temperature Acquisition, Battery and Power-System Monitoring, Laboratory and Instrumentation, Environmental and IoT Sensing Nodes.
Load-Cell and Weighing Systems
The MCP3422A3-E/MC is suitable for resistive-bridge sensors whose output changes relatively slowly, such as platform load cells, force transducers, and industrial weighing modules. Its two differential input channels can acquire complementary bridge signals, helping reject common-mode voltage and reducing the effect of ground offsets in long cable runs. The 18-bit resolution preserves small changes around a mechanical zero point, while the integrated 2.048 V reference provides a stable conversion baseline. The approximately 3.75 samples-per-second A3 rate suits static load, slow ramp, and vibration-envelope measurements. In a practical instrument, connect the bridge output through RC filtering and differential input routing, then compensate in firmware for bridge imbalance and temperature drift.
موصى به
Precision Pressure and Process Monitoring
The MCP3422A3-E/MC fits pressure transmitters, differential pressure cells, and industrial process-monitoring loops where a millivolt-level sensor signal must be digitized reliably. Differential inputs support measurement of a sensor bridge or the difference between two related voltages, reducing sensitivity to common-mode noise generated by adjacent switching circuits. The converter's 18-bit resolution supports fine process-control measurements, and its integrated 2.048 V reference removes the need for a separate reference buffer on space-constrained boards. At approximately 3.75 samples per second, it is appropriate for temperature, pressure, and flow loops that change over seconds rather than milliseconds. Keep analog traces short, use a dedicated analog ground region, and decouple the supply close to the device to maintain predictable conversion accuracy.
موصى به
RTD and Temperature Acquisition
The MCP3422A3-E/MC can acquire temperature information from resistive sensors in industrial equipment, ovens, cold-chain monitoring, and thermal controllers. Its two differential channels allow one converter to handle a pair of RTD inputs, while the high nominal resolution helps preserve small temperature-related resistance changes without requiring a high-speed ADC. The integrated 2.048 V reference provides the excitation and conversion baseline for a ratiometric bridge-style measurement, and the A3 conversion rate is more than adequate for slow thermal processes. For stable readings, connect the RTD through a matched bridge and differential filters, isolate analog routing from digital clocks, and apply software linearization and ambient compensation. The compact 2 mm by 3 mm DFN package also helps when the acquisition board must fit beside the sensor connector.
موصى به
Battery and Power-System Monitoring
The MCP3422A3-E/MC is appropriate for supervisory circuits that measure battery voltage, charger status, or the voltage across a current shunt. Two differential channels can support redundant or sequential power-rail measurements, while the 2.7 V to 5.5 V supply range permits operation in low-energy embedded systems. Its 18-bit resolution can represent small changes in a slowly varying rail or shunt voltage, and the integrated reference supports stable ratiometric measurements without an external precision reference. The A3 grade's approximately 3.75 samples-per-second rate is well matched to energy-management loops. In a battery design, apply the appropriate input protection, account for the ADC input range, and keep the analog divider or shunt node away from high-current switching paths to prevent conversion errors.
موصى به
Laboratory and Instrumentation
The MCP3422A3-E/MC is useful in compact laboratory instruments that require more resolution than a basic microcontroller ADC but do not require waveform-acquisition rates. It can digitize a calibrated sensor output, potentiometer position, or differential measurement produced by an analog front end. The internal 2.048 V reference and differential inputs help simplify calibration and improve immunity to shared ground disturbances, while I2C keeps the connection to an instrument controller compact. The A3 grade provides approximately 3.75 conversions per second, making it suitable for panel meters, laboratory loggers, and calibration fixtures. Preserve measurement accuracy by using a quiet analog supply, separating analog and return currents, validating the gain configuration in firmware, and recording calibration coefficients against the manufacturer's recommended reference conditions.
موصى به
Environmental and IoT Sensing Nodes
The MCP3422A3-E/MC suits compact environmental monitors that combine a resistive or ratiometric sensor with an embedded I2C controller. Its two differential channels can read humidity, gas, soil-moisture, or light-sensor interfaces while the small 2 mm by 3 mm DFN package preserves board area. The 18-bit resolution improves the visibility of small sensor changes, and the integrated reference reduces the component count of the measurement chain. The approximately 3.75 samples-per-second conversion rate is suitable for periodic environmental sampling rather than continuous high-speed capture. Low-power designs should disable conversions between samples, use the device's low-noise analog architecture, and isolate sensitive sensor nodes from radio and DC-DC converter sections. Firmware should also reject outliers and compensate for sensor warm-up and temperature drift.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ MCP3422A3-E/MC — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
Use MCP3422A0-E/MC when the lower conversion grade is sufficient and lower operating activity is preferable. Use MCP3422A2-E/MC when the design needs the same footprint and interface but can accept the A2 timing profile. Choose MCP3422A6-E/MC when faster acquisition is more valuable than retaining the A3 speed grade. For MCP3422A3T-E/MS, confirm the package before substitution because MSOP and DFN require different PCB land patterns. No verified cross-manufacturer drop-in equivalent was established; changing vendors requires a new pinout, timing, gain, noise, and firmware review rather than a footprint-only substitution.
المقارنة مع البدائل
| المعامل | هذا المنتج | MCP3422A0-E/MC | MCP3422A2-E/MC | MCP3422A6-E/MC | MCP3422A3-E/SN |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) | 8-DFN (2x3) |
| Resolution | 18 bits | 18 bits | 18 bits | 18 bits | 18 bits |
| Number of Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Input Configuration | Differential | Differential | Differential | Differential | Differential |
| Internal Reference | 2.048 V | 2.048 V | 2.048 V | 2.048 V | 2.048 V |
| Supply Voltage Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Conversion Performance Grade | A3, approximately 3.75 samples/s | A0 lower-speed grade | A2 lower-speed grade | A6 higher-speed grade | A3, approximately 3.75 samples/s |
| Interface | I2C | I2C | I2C | I2C | I2C |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
أبرز الفروقات
- Balanced conversion speed and high resolution for low-frequency instrumentation (مقابلMCP3422A0-E/MC)
- Compact 2 mm by 3 mm implementation without sacrificing differential measurement (مقابلMCP3422A3T-E/MS)
- Integrated reference reduces external analog component count (مقابلMCP3422A6-E/MC)
- Exact A3 performance alternative for design continuity (مقابلMCP3422A2-E/MC)
ملاحظات التصميم
Keep the two differential analog inputs symmetrical and route them away from the I2C clock and data lines. Place input RC filters close to the converter pins, with the resistor nearer the ADC than the capacitor, so injected noise is attenuated before reaching the input. For a bridge sensor, route the two channels as a closely matched pair to reduce conversion of common-mode noise into differential error.
Decouple the supply at the device with the capacitance recommended by the manufacturer datasheet and keep the connection to the package pin short. If a shared DC-DC converter supplies the analog section, place the analog decoupling before the sensitive sensor connections and keep high-current switching loops on the opposite side of the board. Verify the 2.7 V to 5.5 V operating range at the ADC pins under worst-case supply ripple and load conditions.
Estimated: at a 3.3 V supply, 5.5 V analog input, and 2 mA average device current, the rough converter input-path power is 11 mW; actual device dissipation depends on internal architecture and operating mode and must be confirmed from the datasheet. Because the DFN is only 2 mm by 3 mm, provide the manufacturer-recommended exposed-pad copper area and consider thermal coupling to surrounding components when the board operates at elevated ambient temperature.
Do not substitute the MCP3422A3T-E/MS into an -E/MC board without checking the footprint; the latter uses an 8-MSOP package rather than the 8-pin DFN. Likewise, changing among A0, A2, A3, and A6 grades can alter conversion latency, noise behavior, and valid operating modes. Review the gain table, sample timing, acquisition timing, and digital-filter settling requirements in firmware after any substitution.
معلومات الامتثال
The related MCP3422A3T-E/MS distributor listing identifies the A3 family as automotive AEC-Q100 grade. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the exact -E/MC ordering code should be confirmed on the manufacturer product page.